My BMW had ASC/ABS and Brake pads light on ... I checked and one sensor from brake pads was broken, then I changed the sensor but still had a ASC/ABS and hand Brake led on......If I leave the car without battery one night, the led will go off , but will come on again randomly.China OBD2
Auto Repair
China OBD2 Diagnostic Tools
Porsche PIWIS III Disable/Enable Hidden Functions for Porsche Macan
Lots of small optional PCM features can be activated with Porsche PIWIS III. Obviously, these features must be installed by the factory - you can use PIWIS to see what installed but not activated.Here is a short list of such options:- navigation
- logbook
- voice control
- sports chrono
- satellite radio
- USB
- Bluetooth
- Europe/NAmerica/SAmerica/Asia/MiddleEast/Russia/China/etc map
- PCC
- Telephone
Activation is performed by entering 16 digit hex code into PIWIS, which is then sent to PCM ECU in a single UDS CAN message. This code is derived from VIN and feature you are trying to enable. Given that you can buy these codes easily from various online sites, it's obvious that algorithm has been successfully reverse engineered
Here is an example of what they would do, these numbers are arbitrary, so do not use them in your own car.
Left Front original coding 414, they would add 20 to make it 434
Right Front original coding 416, they would add 20 to make it 436
Left Rear original coding 418, they would add 20 to make it 438
Right Rear original coding 414, they would add 20 to make it 434.
This is basically the logic behind it and these numbers do not mean anything, so do not input them into the car, I have no idea what your factory settings are as each car may be slightly different, they are set at the factory based upon many different parameters.
Also do this at your own risk, as I have no clue on how this will affect your warranty or the service life of the air suspension.
In my opinion, the car actually would look better if you lower the front by 10mm more than the rear, because of the shape of the wheel arches, sometimes the Macan looks as if it is squatting in the back.
Also 20mm is less than an inch and to be honest, it will not even look like you have lowered the car.Good to know:
1.PIWIS III / PIWIS II will allow you to drop your Macan and turn on and off various factory features. It won't do a tune or change the algorithm that controls the valves if you still want them to respond to the buttons. To do that you have to hack the various controllers in the car, or the ECU. While this is standard practise in a lot of the hacker community on common GM, Ford and other ECUs, it is notoriously difficult to do for the Siemens SDI system in late model Porsches.2.PIWIS II is replaced by PIWIS III,PIWIS III is more expensive than PIWIS II, but it can cover newer Porsche cars [Paramera (971) 2018, Caynenne (92A) 2018, Macan (95B) 2018, Macan (95B) 2018, 911 (991) 2018] and have more user-friendly features.
https://blog.uobdii.com
BMW 3 Series 2008 New Key Adding by Yanhua Mini ACDP via OBD
In this instruction,yanhua mini acdp tech will show you the guide on how to use Yanhua Mini ACDP add new key for BMW 3 series 2008 by OBD.More BMW key Programmer please check here BMW Car Key Programmer
Procedures:
Connect Yanhua ACDP Programmer to BMW 3 series OBD portInsert the working key into the key slotRun ACDP app on mobile phone,and select "BMW"-->"CAS3/CAS3+"-->"OBD mode"-->"IMMO"Step 1:Read CAS Data Reading EEPROM dataIt will prompt you to extract the key and wait for about 5 secondsThen tap "Yes" to continue,it prompt you immo data reading successfullyNow save the data "CAS3_ORGKEYxxxx.bin",then click "OK" to continueStep 2:Learn/Disable Key Check the BAV adapter connection and prepare a blank keyNow select the immo data file you save in the step 1Choose the way to program key,select "add key with key"If ask you the key type "smart key" or "not smart key"Insert the blank key,then click "OK" to start new key programmingNow programming successfullyNow save the data file that would be used in step3Insert the original working key into the car key slotStep 3:Update CAS Data It will start updating CAS dataChoose the key data the generated in step 2Choose the way to program key:add key with keyUpdating data successfullyNow you can test new key on BMW 3 seriesMore information about Yanhua ACDP,please check here:
https://www.uobdii.com/wholesale/yanhua-mini-acdp-programming-master.html
How to Use Autel IM608 Generic OBD II Function?
Autel MaxiIM 608,A
fast-access option for OBD II/EOBD vehicle diagnosis is available on
the Vehicle Menu screen. This option presents a quick way to check for
DTCs,isolate the cause of an illuminated malfunction indicator lamp
(MIL), check monitor status prior to emissions certification testing,
verify repairs, and perform a number of other services that are
emissions-related. The OBD direct access option is also used for testing
OBD II/EOBD compliant vehicles that are not included in the Diagnostics
database.Functions of the diagnostics toolbar buttons at
the top of the screen are the same as those available for specific
vehicle diagnostics.
Autel IM608 General Procedure
To access the OBD II/EOBD diagnostics functions
1. Tap the Diagnostics application button from the MaxiIM Job Menu.
The Vehicle Menu displays.
2. Tap the EOBD button. There are two options to establish communication with the vehicle.Auto Scan - when this option is selected the diagnostic tool attempts to
establish communication using each protocol in order to determine which
one the vehicle is broadcasting on.Protocol - when this option is
selected the screen opens a submenu of various protocols. A
communication protocol is a standardized way of data communication
between an ECM and a diagnostic tool. Global OBD may use several
different communication protocols.
3. Select a specific protocol under the Protocol option. Wait for the OBD II Diagnostic Menu to appear.
NOTE
Tapping the button displayed beside the function name opens a bubble with additional function information.
4. Select a function option to continue.
DTC & FFD
I/M Readiness
Live Data
On-Board Monitor
Component Test
Vehicle Information
Vehicle Status
https://www.uobdii.com/wholesale/autel-maxiim-im608.html
How to Use Launch X431 V Program Key for Dodge RAM
Launch X431 V is verified to add two new keys for Dodge Ram successfully.I've logged in here I got to boot Launch X431 V up. I did a system scan
to see what modules it's equipped. We're gonna enter into the wireless
control module that will go hop in the car hopefully.Enter special function.Enter "Program Ignition Keys or Key Fobs".Performing this function may change the state of the vehicle, please exercise caution.This function is to be used when programming a new ignition key or
reprogramming an existing. It will program the win functionality along
with the RKE functions. Ignition should be in run position while running
this function.Okay, we put in a pin.Please verify that is the correct PIN for this vehicle before
continuing. Warning! Entering the incorrect PIN 3 times will cause the
WCM/Win to enter anti-scan lockout.Place un-programmed ignition key into the ignition, turn the key to the run position and continue.Authenticating the PIN.Programming, please wait...Programming of ignition FOBIK was successfully.
Click Yes. And get window message " Place un-programmed ignition key
into the ignition, turn the key to the run position and continue. "Programming of ignition FOBIK was successfully.
Click on "Cancel".Communicating, please wait...I called my friend, and he says not all Chrysler have the PM RFH module,
questions me whether or not the vehicle had remote start.
These are the other key fobs the new ones.
We could use this one and see if the remote start works. And it does, so it's good.
Then we spill it stick it in turn it on, security light on and security light out.Job is done.Launch X431 V8 is excellent, help me save hundreds of dollars.
https://www.uobdii.com/wholesale/launch-x431-v-8-inch-tablet-wifi-bluetooth-diagnostic-tool.html
Honda HON66 Key Cutting by Alpha Key Machine
Here keycuttingmachine.org show you guide on how to use Alpha key cutting machine to cut key for Honda Accord.
Another option for Honda HON66 key cutting is 2M2 Key cutting machine
Procedures:
3 Ways to enter Honda Accord Key Data
1.Manufacturer,Model,Year
2.Key Blank Number
3.ID Number
1.Manufacturer,Model,Year
Click "Automobile" button and select "Honda"-->"Accord"-->"2010-0"-->"K001-M999,N001-N7" to enter key data.
2.Search by Key Blank Number
Click "Search" button,input "HON66"-->"13416-{6-6}"
3.Search by ID NumberFix a new key blank on the tip level of Side BClick "Cut" button to start cutting (Close the shield)Start cuttingRepeat work for the other side,after cutting done.
Open the shield to get the new key (clean shavings)
https://www.uobdii.com/wholesale/alpha-automatic-key-cutting-machine.html
Article from:
https://www.keycuttingmachine.org/honda-accord-key-cutting-by-alpha-key-cutting-machine/
Honda HON66 Key Cutting by Alpha Key Machine
Here keycuttingmachine.org show you guide on how to use Alpha key cutting machine to cut key for Honda Accord.
Another option for Honda HON66 key cutting is 2M2 Key cutting machine
Procedures:
3 Ways to enter Honda Accord Key Data
1.Manufacturer,Model,Year
2.Key Blank Number
3.ID Number1.Manufacturer,Model,Year
Click "Automobile" button and select "Honda"-->"Accord"-->"2010-0"-->"K001-M999,N001-N7" to enter key data.2.Search by Key Blank Number
Click "Search" button,input "HON66"-->"13416-{6-6}"3.Search by ID NumberFix a new key blank on the tip level of Side BClick "Cut" button to start cutting (Close the shield)Start cuttingRepeat work for the other side,after cutting done.
Open the shield to get the new key (clean shavings)
https://www.uobdii.com/wholesale/alpha-automatic-key-cutting-machine.htmlArticle from:
https://www.keycuttingmachine.org/honda-accord-key-cutting-by-alpha-key-cutting-machine/
How to Use Yanhua Mini ACDP Clone BMW ECU DME
Yanhua Mini ACDP BMW ECU Clone update:
- Read and write Dflash / Pflash for BMW DME (N13,N20,N63,S63,N55,B38 etc), then perform DME clone.
- Read and write the data without removing DME shell and punching.
- More ECU types will be added one by one.
Choose "BMW".Then ECU clone.Then DME type, any of N13 N20 N63 S63 N55 B38Function Menu:
Identify
Read /write DFLASH
Read/write PFLASHFor the following operation, please follow the on-screen instruction.
When Yanhua ACDP engineer have time, we will make video and share with you.
Volvo 88890300 Vocom TechTool PTT Software Installation Guide
Volvo Premium Tech Tool software has released to V2.03. The newest
V2.03.85 is verified working. Here is the instruction on installing PTT2.03 software.
Software version: V2.03.85
This software can be purchased in uobd2, price is 230usd.
Hardware:
The PTT V2.03 software must be loaded with Volvo 88890300 Vocom interface Volvo Vida Dice 2015A Software
Truck makers support:
Volvo/Renault/UD/Mack EURO4, EURO5, EURO 6 system
Language:
English, French, Spanish, German, Italian, Russian, Hungarian, Dutch,
Danish, Chinese, Norwegian, Polish, Turkish, Czech, Swedish, Japanese,
Thai
Operating system:
Windows 7 professional or ultimate
How to install Volvo Premium Tech Tool V2.03.85 software?
NOTE: After you pay the software, we will provide the software
download link. Software requires activation. Please provide the
TeamViewer ID and password to activate.
- Download all files, copy to usb-hdd.
- Unzip Acronis Boot 2014.part1.rar (need win.rar 5.0 above version)
- Burn Acronis Boot 2014.iso into CD Disc
- Unzip Tech Tool 2.03.85 (With APCI+ Update!)_Final.part01.rar, password: E29A11A8EE81DD9D1606BD83BBA26559, will get Tech Tool 2.03.85 (With APCI+ Update!)_Final.tib
- Insert acronic boot CD, boot laptop
- Recovery -> choose Tech Tool 2.03.85 (With APCI+ Update!)_Final.tib-> recovery to laptop harddisk
- Reboot PC, now you will get ptt2.03 with new win7 system , then go to install driver
- Copy TechToolCoreDevelopmentContent.rar and VCADSProDevelopmentContent.rar to desktop
- Send us Teamviewer ID password, our foreign engineer will active it
UOBDII Official Blog All rights reserved How to install Volvo 88890300 Vocom TechTool PTT2.03
Orange 5 ECU Programmer Softwaer Installation Guide
This is where your text starts. You can click here and start typing. Porro quisquam est qui dolorem ipsum quia dolor sit amet consectetur adipisci velit sed quia non numquam eius modi tempora incidunt ut labore et dolore magnam aliquam quaerat.
How to Use VVDI Prog Read & Write BMW CAS4 Data without Soldering
It is necessary to remove and solder for BMW CAS4 data reading,it will
cause data damaged/loss.So here give the solution without removing and
soldering during you use VVDI prog Programmer to reading data from BMW CAS4.
What You Need?
BMW CAS4 Clip Adapter
Xhorse VVDI Prog
BMW CAS4 Data Reading Socket can prevent data loss, specialized for VVDI PROG Programmer
BMW CAS4-5M48H-1N35H, easy to operation, no need disassembling, no need welding, it is a powerful data reading tool.CAS4 clip adapter includes adapter cable (for vvdi pro), clip A and clip B.
Before using clip A and clip B, please use one blade to remove the glue
on the contact surface to prevent poor contact between the probe and the
circuit board.Read BMW CAS4 data wiring diagram
Note:
This auxiliary clip reads CAS4 data without welding, but it lengthens
the length of the wiring harness. Some types of CAS require multiple
attempts to read out. It is recommended to try 3-5 times (the data will not get lost). If you can't read the data after repeat attempts, please read the data in the traditional method.
SVCI V2020 Diagnostic Tool Customer Feedback
Here collect the customer feedback on SVCI 2020 diagnostic tool.
Question: What can do scvi2020 that not can do fvdi 2014?
Answer: support new cars : Renault , FIAT , VW .... , VVDI2 include , better tag key tool to prepare specials keys ...
For the price , you can bought it ( 230€ )Question: Can SVCI V2020 work normally when the network is connecting?
Answer: No need to connect the network. If the network is connecting when using SVCI, it won't damage the machine.Question: Is SVCI FVDI V2020 available with multi language?
Answer: yes, you can reset the language in the car model list.
Also, the svci 2020 software has language list.Question: Any computer operation system requirements for svci 2010?
Answer: win7, 8 , 10 are all okay.
Question: SVCI V2020 is 12 months activation or lifetime?
Answer: No need activation.
Question: Does SVCI V2020 have button batteries?
Answer: No, it doesn't. Without battery, the machine won't lock and easy to ship.
Question: can SVCI V2020 correct odometer for Fiat?
Answer: Yes, it can cover Fiat up to 2015 year.
Question: Can SVCI V2020 support Audi a5 2011 bcm2 component protection?
Answer: Yes, it can.
Question: Can SVCI V2020 support audi a5 2011 bcm2 synchronization?
Answer: No. it doesn't support the online function.
Question: Does SVCI V2020 have J2534?
Answer: No.
Question: Is SVCI V2020 compatible with the AVDI software?
Answer: No. It can't work with other machine, the software is bound together with the serial number.
Question: Does SVCI V2020 have key programming function?
Answer: yes.
Question: Can svci 2020 support the special functions of VAG, BMW, Benz, such as mileage correction and key learning?
Answer: yes, basically up to 2014 year.SVCI 2020 Diagnostic Tool
How to Use Vident iEasy310 Read and Clear DTCs
This instruction show you the overview on how to use Vident iEasy310 to read & clear DTCs.
Vident Scanner Tool
Read Codes
Read Codes menu lets you read stored codes, pending codes and permanent
does found in the control unit. Typical menu options include:
- ● Stored Codes
- ● Pending Codes
- ● Permanent Codes
- ● Press the Erase hot key to erase codes from home screen.
- ● Traditional way: select Erase Codes from the diagnostic menu.
Comparion Yanhua ACDP & CGDI BMW for BMW Key Programming
All auto locksmith,especially for BMW key programming know that Yanhua Mini ACDP programmer and CGDI BMW programmer both performing good on BMW CAS1-CAS4+,FEM/BDC key programming.So here UOBD2 engine show you the difference between them.
Features/Tools
Yanhua Mini ACDP BMW
CGDI BMW
Image
Highlight
No need to remove chip!
No need soldering!
No need to cut the line!
No need to lift the pin!
OBD key program!
Run faster!
Test a lot = Safety!
Workable interface
Mobile with Android or iOS
PC or Laptop
Connection
Wifi connection to a mobile
Wired connection to a PC
Update
Free and online update https://yanhuaminiacdp.blogspot.com/
Free and online update in https://www.cgdisupport.com/
Tokens
No need tokens
No need tokens
Note: It's necessary to buy
Tokens if it's CGDI-MB.
Method
OBD
OBD
Key programming
CAS1: Yes
CAS2: Yes
CAS3: Yes
CAS3+: Yes
CAS4: Yes
CAS4+: Yes
FEM/BDC: Yes
CAS1: Yes
CAS2: Yes
CAS3: Yes
CAS3+: Yes
CAS4: Yes
CAS4+: Yes
FEM/BDC: Yes
Odometer correction
Yes
Yes
F series coding
Yes
Yes
EGS ISN reading
Yes
Yes
Activation/Adapter
ACDP needs adapters to work with.
You should buy different adapters for various modules:
CAS1-4+ immo;
FEM/BDC immo & dashboard;
FRM footwell module (0L15Y 3M25J);
35080, 35160DO WT Eeprom.
And you should have another adapter to read ISN;
adapter to read DME ISN (when all keys are lost);
adapter to renew key.Btw, you can get a Mini ACDP FULL kit.
CGDI doesn't need adapter to work with.
But you need another programmer to read modules, need a cable to read DME ISN from MSV and MSD
And you should get authorization for some functions:
BWM FEM/BDC Authorization
In short,
If you are not equipped with soldering knowledge & rich experience and don't have another tool to read modules, Yanhua ACDP can be a good helper.
For personal use, you're advised to have a Mini ACDP main unit and the adapter for your BMW.
For auto repair, have a Yanhua Mini ACDP FULL kit = have all for BMW key making and module programming.
https://www.uobdii.com
How to Use Autek iKey820 Do All Key Lost Programing for Ford Explorer 2015
This instruction show you guide on how to use Autek iKey820 to perform all key lost programming for Ford Explorer 2015.Car: 2015 Ford Explorer
Key: ALL keys lost
Purpose: Program a new key when all keys lost
Key programming tool: Autek iKey820
Steps:
Step 1: select the car model in Autek ikey820
Ford - by vehicle - Explorer - 2015 - keyless
Step 2: read the key qty with Autek
loading database...turn ignition offread key qtytotal keyless: 2
Step 3: add keyless using Autek ikey820
add keylessput the new keyless into slot and turn ignition oncominicating....(wait for 10 min around)success!
Autek ikey820 programmer managed to program a new key to Explorer 15'.For more information about iKey820 programmer,please visit iKey820 blog:
https://autek-ikey820.blogspot.com/
How to Use Vident iLink400 to Perform Auto Scan and Control Unit Selection?
This instruction show you guide on how to perform auto scan and control unit selection by Vident iLink400 When you have completed the identification of vehicle by Vident iLink400, a menu for selecting systems to test displays. Menu options typically are
- ● Auto Scan
- ● Control Unit
- https://blog.uobdii.com
Auto Scan performs an automatic system test to determine which control modules are installed on the vehicle and obtain diagnostic trouble codes (DTCs) overview.
1. Select Auto Scan from the menu and press OK to start.2. When auto scan finishes, a menu with a list of installed controllers together with their DTC overview displays.3. If there is diagnostic trouble code(s) detected in a control unit, press the function key corresponding with Display DTC on the screen to view details of code information, and press the function key Quick Erase to clear them.
4. Select the system you would like to test, and press the OK key. When the scan tool has established connection with the vehicle, the Function Menu displays.Control Unit
Control Unit screen displays all controllers available to this specific vehicle manufacturer.
1. Select Control Unit from the menu and press the OK key. A controller menu displays.2. Select the system you would like to test. When the scan tool has established connection with the vehicle, the Function Menu displays.Vident iLink400:
https://www.uobdii.com/wholesale/vident-ilink400-scan-tool-single-maker.html
Autel IM608 Read and Clear Diagnostic Trouble Codes
This instruction focus on how to use Autel IM608 to diagnose your vhicle,it show you read and clear diagnostic trouble codes.Now,Autel company released their Autel APB112 key simulator used with Autel IM608 and Autel IM508.
Autel IM608 Read & Clear DTCs:
Connect IM608 to vehicle,then enter menu to select diagnosis,and select Auto Scan to identify vehicle.
This function retrieves and displays the DTCs from the vehicle's control
system. The Read Codes screen varies for each vehicle being tested. On
some vehicles, freeze frame data can also be retrieved for viewing. The
sample Read Codes screen displays as below:
1 Autel MaxiIM608
Diagnostics Toolbar Buttons - see Table 4-2 Operation Toolbar Buttons
on page 38 for detailed descriptions of the operations for each button.
2Main Section
Code Column - displays the retrieved codes from the vehicle.
Status Column - indicates the status of the retrieved codes.
Description Column - detailed descriptions for the retrieved codes.
Snowflake Icon - only displays when freeze frame data is available for
viewing; selecting this icon will display a data screen, which looks and
behaves similar to the Read Codes screen.
3.Functional Button
Help - tap to view fault code information, including fault
description,condition for fault identification, and driver information.
Freeze frame - tap to view the freeze frame data.
Search - tap to search related fault code information on Google.
ESC - tap to return to the previous screen or exit the function.
Erase Codes
After reading the retrieved codes from the vehicle and certain repairs
have been carried out, you can decide to erase the codes from the
vehicle using this function. Before performing this function, make sure
the vehicle's ignition key is in the ON (RUN) position with the engine
off.
To erase codes
1Tap Erase Codes from the Function Menu.
2A warning message displays to advice of data loss if this function is completed.
a) Tap Yes to continue. A confirming screen displays when the operation is successfully done.
b) Tap No to exit.
3Tap ESC on the confirming screen to exit Erase Codes.
4Perform the Read Codes function again to check if codes have been erased successfully.https://www.uobdii.com/wholesale/autel-maxiim-im608.html
How to Uuse Yanhua Mini ACDP View BMW VIN?
Yanhua Mini ACDP update: Both IOS & Android users can view the vehicle info by VIN before going to program. Please upgrade your app from App Store.If you are beginner of Yanhua Mini ACDP,please watch this video guide:
https://youtu.be/xXt2jlAOLuc
Purpose: In order to confirm whether Yanhua Mini ACDP can program the user's key.
Such as:
- When you only know the car model and year, this software will help confirm the BMW IMMO is BMW CAS1-CAS4+or FEM/BDC.
- If all keys lost, it requires to read out the engine ISN code, but the user doesn't know the ECU model, then this software will help. Which is helpful for both users and dealers.
Part 1. For IOS user, you can follow the next procedure to view the vehicle info by VIN:
2.Select "App store".
3.Vehicle information.
4.Option: "From image" or "from clipboard", then click on "Query".
5.BMW vehicle info in details.
Part 2. For Android user, you can follow the next procedure to view the VIN.
How to update XTOOL PS2 GDS Gasoline Diagnostic Tool
This instruction show you the guide on how to update XTOOL PS2 GDS gasoline diagnostic tool.
How to update XTOOL PS2 GDS?
1) go to www.xtooltech.com and login in to user center with User Name and password.
2) Select "Download Center" option under "Navigation" tab
3) Enter Download Center program, download the "Update Tool"4) Then download the software you need to update5) Save the update software to be downloaded to a certain folder
6) Open and run Xtool "Update Tool-V* exe" setup on the desktop7) Follow the system prompt until the update tool installation is completed
8) Then remove the SD card from the Xtool PS2 truck diagnostic tool to the SD card reader and then connect it to the computer.
9) Open the Xtool Update Tool on the desktop when the SD card has successfully connected with your computer10) Click the browse button to select the folder where you going to put the software winrar files.
Click Confirm button and it will reads your PS2 serial number and the software.11) Select the software to be updated and click the Update button to update12) Wait until PS2 GDS software update is completed.
https://www.uobdii.com/wholesale/xtool-sd100-volle-obd2-code-reader.html
How to Use VVDI Super Chip & Mini Key Tool Clone Ford Mazda 8C
Here uobd2 show you the test report on VVDI super chip and VVDI Mini Key programmer to clone Ford Mazda 8C.
Compatibility:
VVDI2 v6.5.0 or newer version
VVDI KEY TOOL
VVDI MINI KEY TOOL
Procedures:
Put the original car key into the coil for identification.
Tap "Transponder Clone".Tap "Read Transponder".Select "Ford/Mazda 8C clone".Start Clone.https://www.uobdii.com/wholesale/xhorse-vvdi-super-chip.html
How to Use Foxwell NT530 to identify Vehicle VIN?
Here UOBD2 show you the guide on how to use Foxwell NT530 to identify vehicle identify number.How to use the Foxwell NT530 scanner to identify the specifications of the vehicle under test.The vehicle identification information presented is provided by the ECM of the vehicle being tested.Therefore, certain attributes of the test vehicle must be entered into the scan tool to ensure the datadisplays correctly. The vehicle identification sequence is menu driven, you simply follow the screen prompts and make a series of choices. Each selection you make advances you to the next screen.Exact procedures may vary somewhat by vehicle. It typically identifies a vehicle by any of thefollowing means:SmartVIN
Manual selection Foxwell NT530 Smart VIN Mode:
Smart VIN allows to identify a vehicle by automatically reading the vehicle identification number (VIN).
To identify a vehicle by SmartVIN:
1. Scroll with arrow keys to highlight the vehicle application from main menu and press ENTER.2. Select SmartVIN from the menu, and press the ENTER key.3. The scan tool starts to communicate with the vehicle and read the Vehicle Specification or VIN
Code automatically.4. Answer YES if the Vehicle Specification or VIN code is correct and a menu of controller selection
To identify a vehicle by manual vehicle selection:
CGDI Prog Latest Update on FEM/BDC Operation Notes
This article is to share the newest info of CGDI Prog BMW MSV80 Key Programmer. Include latest update info, FEM/ BDC operation notes.CGDI BMW Earth-shaking Update (June 11th, 2019)
1.Add BMW E-series iDrive Coding2.Add BMW Diagnosis and support BMW E/ F/ G series DTC reading and clearing.
Note: CGDI prog BMW diagnostic function can free open and upgrade
Learn more update info as below
CGDI Prog BMW V2.6.0 Update (March 5th, 2019)
1Added: EWS1-3 key matching function
2The E-code is modified to modify the VO code function, and the VO code
can be added or deleted directly by the selection method, and the
operation is simpler.
3The BMW data modification adds support for both N13 and N55 engine data.Free download link: https://www.cg100iii.com/download/CGDI_Setup_V2.6.0.zipBMW FEM/ BDC Operation Notes
FEM/BDC installation locationChips Operation location Display
95128 IC location95256 IC locationKey learning position
Article from:https://www.cgdisupport.com
VXDIAG VCX SE BMW Diagnostic Tool Reviews
Here is a mini post on VXDIAG SE BMW Diagnostic Tool Reviews
VXDIAG VCX SE BMW Function List
1.ECU Upgrade Programming coding,change vehicle configuration VO,import vehicle FSC activation code
2.Matching control unit sets code,changes vehicle configuration and activation code,deletes hidden function
3.Import/Export Data
4.Flash programming of Control Unit
5.ECU version upgrade/downgrade,ECU repair after ISSS programming Failure
6.Manual input parameter reading module,reset fault software/hardware Number
7.Vehicle Diagnosis,Delete Fault code,read vehicle data
8.Brush Hiding function,circuit parts drawing query,accessories query,etc.How to Connect VXDIAG VCX SE Between BMW & PC?
Connect VXDIAG VCX SE BMW to BMW vehicle obd port directly,or you also
can connect it by connector,then connect VXDIAG VCX SE BMW to PC by
connector cable.https://www.cgdisupport.com
TOPDON ArtiPad I:How to Feedback Diagnostic Logs?
TOPDON ArtiPad I have diagnostic logs feedback function,you can feedback the your diagnostic logs to TOPDON engineer.This item allows you to feedback your diagnostic problems to us for analysis and
troubleshooting.
Tap "Feedback", a pop-up message will appear:Tap "CONFIRM" to choose the vehicle diagnostic record page.A). Tap the desired vehicle to enter the TOPDON ArtiPad I Diagnostic Tool diagnostic log selection page.Select the check box and tap "Submit". A screen similar to the following will
appear:
Choose the failure type and fill in the detailed failure description in the blank text
box and telephone or email address. After inputting, tap "Submit Result" to send
it to us.B). Tap "History", the diagnostic logs marked with different color
indicate the process status of the diagnostic feedback. Green/Red/Blue
means the diagnostic feedback is fixed/pending/in process respectively.For more details about TOPDON ArtiPad I Diagnostic Tool,please check here:
https://www.uobdii.com/wholesale/topdon-artipad-i-diagnostic-tool.html
Autel MaxiIM608 Test on Dodge Smart Key PIN Code
This test report feedback from our customer real test project,he use this new product Autel MaxiIM608 to read PIN code for Dodge smart key.https://youtu.be/dgyDl9TODas
Operation Procedures:
Connect Autel IM608 to vehicle,then enter menu to select "Dodge"Select "Smart Mode"Turn the ignition on
If it is old pre 2006 model,please give priority selection to "Manual Selection" or "System Selection"!Establishing vehicle communicationSelect "knob-style smart card"Switch the ignition off and then on again,make sure the engine off.Establishing vehicle communication...Switch the ignition off and then on again,make sure the engine off.Establishing vehicle communication...Then you will get the PIN code:8095
Yanhua ACDP Program New Key for VW Passat MMC All Keys Lost
This article show you the procedures on how to use Yanhua Mini ACDP programmer to program new keys for VW Passat MMC all key lost programming.More Yanhua Mini ACDP post,please check here:Yanhua Mini ACDPPreparations:
1). Yanhua ACDP basic module
2). VW MQB/MMC Instrument Module6 + authorization
3.Software installation:
Yanhua ACDP Software Installation Download Guide for Iphone IOS
Yanhua ACDP Software Installation Download Guide for Android
Step 1: Download, install, settings
* Take Android Phone for example.
1). Browse https://www.acdpmaster.com (Yanhua ACDP official site), click on "Resource download". Donwload "ACDP Android APP", use my phone to scan the QR code.2). Get the link: https://www. pgyer.com/acdp , click on
it to download. Click the icon in the top right corner showed in the
picture and open it in the corresponding browser.3). If you can't see the icon shown as following image 1, tap "Mine",
then "System settings", then "App and resource update" , then " Resource
file update" and "Resource fix" (image 2), finally, you get to normal
menu (image 3)4). Bind your ACDP to the computer & register the account.
Any question, just tap "Manual" for instructions.Step 2. Perform VW MQB MMC mileage correction
Tap "VW" and get options:
MQB Platform Instrument
Passat MMC Meter (2015- )
Touareg (2011 -)1) MQB Platform Instrument with ACDP:
Instrument with NEC35xx (Continental /VDO)Adjust mileageAuto mode and Advanced modeTap "Auto mode" then get option " Adjust mileage".Tap " advanced mode" and get options: reading mileage, adjust mileage, backup data, recover data etc.2) Passat MMC meter (2015 -) with ACDP:
NEC D70F3525 + 95320Tap "Help" for wiring diagramGo on......
As you can see, you will feel easy to use Yanhua ACDP to perform MQB Platform Instrument and Passat MMC meter (2015 -).MQB VAG Programmer
CK360 Easy Check Tester Identify VW MQB-A and MQB-B Key
CK360 Easy Check
Remote Tester is a new Remote Key Tester for Frequency 315Mhz-868Mhz
& Key Chip & Battery 3 in 1, also support Mercedes infrared key
detection and Intelligent signal detection,best choice for technicians
and repair shop.And here OBD2 will show you how to use it to detect VW
MQB keys,include MQB-A and MQB-B.
Note:VVDI Mini Key Tool,Tango and Handy Baby 2 can not identify MQB-B key,but CK360 tester can!
CK360 Tester Identify VW MQB-A and MQB-B Key:
Power on CK360 Easy Check tester, then select key identification menu and put the key on the coil.
Press power buttonThen CK360 will start key identification,please waitNow it show the key information:
49+ type
ID:C60A1E3F
MQB-BAnd press back button,then put another key on the coilPress power button to start identification
Show the key information:
48 type
ID:0AB0E06A
MAB-ADone!More detail about CK360 Remote Tester,please check here:
https://www.uobdii.com/wholesale/ck360-easy-check-remote-key-tester.html
How to Use SEC-E9 Machine Cut Tubular key?
In this article keycuttingmachine will show you how to use SEC-E9 machine to cut tubular key,hope it helps!what is a tubular key?
Tubular keys are short keys with a hollow shaft most often used to
open vending machines to retrieve coins and cash. A universal tubular
key is one that is cut to fit a set of machines so that there is not a
separate key for each machine.
How to do tubular key cutting?
First you should have a key cutting machine for tubular keys
Tubular keys can be cut with SEC-E9 key machine.
Second you need a tubular key clamp
Source: https://www.uobdii.com/wholesale/tubular-key-clamps-for-sec-e9-key-cutting-machine.html
This is the tubular clamp tested ok with the SEC-E9 machine
Third, here is the tubular key list done by SEC-E9Car Brand
Model
Year
IC Card
AGA
AGA
0-0
8647
AGA
AGA 12 CSS2
0-0
8648
AGA
AGA 42
0-0
8649
AGA
AGA 39
0-0
8650
AGA
AGA 37
0-0
8651
AGA
AGA
0-0
8652
AGA
AGA
0-0
8653
AGA
AGA
0-0
8654
AGA
AGA
0-0
8655
AGA
AGA
0-0
7096
Beaver
Beaver
0-0
6559
Bilma
Bilma
0-0
8608
Bumil
Bumil
0-0
6558
Chicago
Chicago
0-0
6543
Dynaconsult
Dynaconsult
0-0
6556
Fort
Fort
0-0
6557
Fort
Fort
0-0
6549
Lowe&Fletcher
Lowe&Fletcher
0-0
6551
LYF
LYF
0-0
8606
LYF
LYF
0-0
8607
Meroni
Meroni
0-0
6546
R.O.C.
R.O.C
0-0
6550
R.O.C.
R.O.C
0-0
6552
R.O.C.
R.O.C
0-0
6553
Ronis
Ronis
0-0
6554
SAG
SAG
0-0
8656
Sentry
Sentry
0-0
6555
Fourth, SEC-E9 and tubular key test report
Tubular key cutting done with SEC-E9 key cutting machine:source:
https://www.uobdii.com/wholesale/sec-e9-cnc-automated-key-cutting-machine.html
CGDI MB Benz W164 All Key Lost Programming EIS Data Collection
For traditional method for Benz EIS data collection,it will take you
about several hours.It is inefficient,so here I share the guide on how
to solve Benz EIS data collect inefficiently,here I take Benz W164 as
example.
Preparations:
CGDI Benz Prog
CGDI Benz AC Adapter
And for the Benz key programming you can reference this video guide:
https://youtu.be/IFZk4ytJusI
Procedures:
Run CGDI MB Monster software and select "Wiring Diagram",then check the wire harness diagramFollow the wire diagram to build wire harness connectionSelect "EIS" option at left menu bar,then click "Read EIS data"After reading EIS data,click "Compute Password" at left menu bar
Chose "Copy key without key",and click "Collect Data".
Then select "Platform mode(Quick collect)" and click "OK" to start data collection.Note:Here need CGDI MB AC AdapterPlease insert the simulation key within 1 minutes,if you have inserted,please pull out and try again.
(Please turn the quick collect adapter switch to the Platform position.Turn the key to ignition ON position)It will take you about 6 minutes to collect data,please wait...
Note:By traditional method,you need spend hoursAfter data collection completing,save the data on your laptopThen click "Upload Data" button to upload the data you save just now for password caculationUpload data successfully,please click "Query Reqults" buttons to queryCalculation successfullyDone!
https://cgdi.over-blog.com/
How to Connect Yanhua ACDP to Your Mobile Phone
Here comes the guide on how to connect Yanhua ACDP to mobile phone.If is necessary for fresh man on first time user to get it.And for more article about Yanhua Mini,please check here:Yanhua Mini ACDP Tech
Here is a Youtube guide on how to use Yanhua Mini ACDP:
https://youtu.be/xXt2jlAOLuc
Procedures:
1、Open the Bluetooth and connect the WiFi;2、Open the ACDP on your phone and click setting as the following icon;Click "Initial use settings"3、Following the directions: press and hold the "SET" button on the ACDP
device for about 7s till the device's buzzer sounds, then release the
"SET" button. Then click "Next";4、Choose the device;5、Enter the password of WiFi, then click "Start configuration";6、Bond the device;
7、Bonded successful as the following. Article from Yanhua Mini Tech Blog:
https://yanhuaminiacdp.blogspot.com/2018/06/how-to-connect-yanhua-acdp-to-your.html
Launch X431 CRP429C Smart & Manual Diagnostic Guide
Here obd2 share the guide on how to use Launch X431 CRP429C smart & manual diagnosis function.
Launch CRP429C Smart Diagnosis:
After connection, turn the ignition key on and the system enters auto-detect mode.
Note: To detect more and accurate VINs, a stable network connection is highly recommended for this function.
CAUTION: Don't connect or disconnect any test equipment with ignition on or engine running.
A. Once the system successfully obtains the VIN (Vehicle Identification
Number) information of the currently identified vehicle, it will
continue scanning the vehicle systems. After the scanning is complete, a
diagnostic report will be automatically generated and sent to your
email box (if bound).
B. If the tool failed to access the VIN information, the screen will display as below:Input the VIN, and tap "OK", the system will automatically identify the vehicle
model. If the vehicle VIN is successfully decoded, it will perform autodiagnosis
until a diagnostic report is automatically output. Otherwise it will
enter manual diagnosis mode.
Notes:
• The most recognizable location for this number is in the top left corner on the
vehicle's dashboard. Other locations include the driver's door or post, and the
firewall under the hood.
• In general, vehicle identification numbers are standardized - all contain 17
characters. VIN characters may be capital letters A through Z and numbers
1 through 0; however, the letters I, O and Q are never used in order to avoid
mistakes of misreading. No signs or spaces are allowed in the VIN.Here is video guide on how to use Launch X431 CRP429 to diagnose for BMW
https://youtu.be/Gpy27mwxsh4
Launch CRP429C Manual Diagnosis
If the tool can not obtain the VIN information, you can also perform vehicle
diagnosis manually. In this mode, you need to execute the menu-driven
command and then follow the on-screen instruction to proceed.
Notes:
• Before diagnosing, please make sure the diagnostic program corresponding to certain vehicle model has been installed on your CRP429C.
• For vehicles manufactured by different vendors, it is possible that it has different
diagnostic menus. For details, please follow the instructions on the
screen to proceed.Refer to the flowchart illustrated as below to
diagnose a vehicle manually:Take Demo as an example to demonstrate how to diagnose a vehicle.
1). Select diagnostic software version: Tap the "DEMO" to go to Step 2.2). Select test item: Select the desired test item to proceed.More information about Launch CRP429C,please check here:
https://www.uobdii.com/wholesale/launch-x431-crp429c-auto-diagnostic-tool.html
How to Use CGDI MB Prog to Read/Clear/Write Mercedes Benz NEC chips
This mini post show a test report on CGDI Mercedes programmer read,clear,write a NEC chip.And for more CGDI MB programmer test case,please check here:CGDI Benz Test Cases
Note:Download CGDI software here:CGDI BMW BENZ Software Download
Procedures:
step 1 dismantle the key and desolder the NEC chip
step 2 clean the pcb and nec chip before welding back on the board
step 3 identify the nec chip and weld onto the nec board
step 4 select the nec adapter and corresponding chip type
step 5 read key/chip
step 6 reset
step 7 if you have key files already, open/writesuccess!
step 8 read key/chip to confirm the success of key writing
Done!
CGDI MB is able to read and write NEC chips!
VVDI MB 4.7.0 New Version Update Information
Here is newest VVDI MB Programmer Tool 4.7.0 Update information,and you can download and update it to this version.Released notes:1. This update no need update the firmware
2.Password calculation for ALL KEY LOST:
Support W164/W251(-2009), W221 calculate password when all key lost:
a. Support W164/W251(-2009) get key password with slow method (All KEY LOST, 25minutes-1.5hour)
b. Support W221 get key password with VVDIMB Power Adapter (All KEY LOST, no need re-insert IR, 15minutes)
c. Support W221 get key password with slow method (All KEY LOST, 25minutes-1.5hour)EIS (FBS3) list: all keys lost
VVDIMB support all key lost EIS type (FBS3) as listed below
W166, W197, W212, W218, W246,W172, W204, W207,W216
W164, W251 (-2009)
W164, W251 (2009-)
W169, W209, W211
W202, W208, W210
W203, W463, W639
W639(2009-)W906
W221 VVDI MB car list: all keys lost
VVDI MERCEDES version 4.7.0 supports the following models all keys lost and can program new keys without soldering:
W166 W197 W212 W218 W246
W172 W204 W207
W216
W164 W251 (-2009)
W164 W251 (2009-)
W221
W169 W209 W211
W202 W208 W210 W203 W463 W639
W639 (2009-)
W906
Test: Tested successfully by one of our customers
VVDI MB V4.7.0 confirmed MB W221 AKL All Keys Lost tested successfully by one of a prominent customers in Libya
This perhaps could be the 1st W221 In the world � to get a set of working keys without having EIS replacedUOBDII Official Blog All rights reserved VVDI MB 4.7.0 download with FULL list of EIS (FBS3) all keys lost
BMW E/F Scanner Read BMW CAS1-CAS3+ ISN Code Operation Guide
Here I want to share the guide on how to use BMW E/F scanner II to read out BMW CAS1-CAS3+ ISN code.And for more information please visit BMW E/F Scanner blog BMW E/F Scanner
Interface:
V2018.12 BMW E/F Scanner II Full Version (Recommend)
2013.07V E/F SCANNER For BMWThe BMW Explorer program has a possibility of reading a code of synchronization of ISN (all versions of CAS1 CAS2 CAS3 CAS3+).
Go to the CAS control unit, "Additional functions", "Reading ISN"
In the opened window ISN will be displayed.
If the machine is equipped with the EWS3 system where 2 bytes of the
constant part and the change are used, it will be displayed in the
window 2 bytes of ISN DME (the upper 3 windows will be empty), if
necessary they can be changed.If the machine uses the EWS4 system, then 16 bytes of constant synchronization are used and there is no variable part.
Also after 2006, CAS3 uses an anti-theft code for EGS
If there is an EWS3 system in the car, then this code is the same
with the engine control unit, if the machine already has an EWS4 system,
then EGS uses separate 2 bytes
The program is in place of the engine ISN, it will display the gearbox code .. as in the picture below
UOBDII All rights reserved How to Use BMW E/F Scanner Read BMW ISN Code for CAS1-3+
How to Solve Hyundai & Kia GDS VCI "CRC Error"
Recently,some customers ask the solution for their Hyundai & Kia GDS VCI "CRC" Error.So here UOBD2 share the procedure to solve this problem.
And for more auto diagnostic toolTrouble Descriptions:
Installing Hyundai GDS (Global Diagnostic System) software on Win 7 laptop, when come to Hyundai master setup wizard installation step, the system reported an error:"CRC error: The file C:/gvci/ocx/install/dotnetfx-eng.exe doesn't match
the file in the setup's.cab file. The medium from which you are running
the setup may be corrupted; contact your software vendor."Error screen
Possible reason:
1. Operating system issue
2. Improper installation steps
3. Software damaged
Solution:
Please follow the video or blog guide (below) to install GDS program. If
the Hyundai master setup can be well installed, but others cannot, then
send the specific file name that cannot be installed to obd365 customer
service. We will resend the file.We recommend users to choose U-Disk format software rather than CD software. U-Disk format GDS V2.14 software HDD is easier to install.
FVDI 2015 2016 Device Locked Solution
Here UOBD2 give out the solution to solve FVDI 2015 2016 locked error,hope it helps!
And check here for newest FVDI 2018
https://www.yanhuaacdp.com/
The symptoms show as below:
1.FVDI device can not work
2.Green led light of FVDI unit is off
3 .Red-green led of software dongle(red dongle) blink.Here UOBD2 engineer give the solution:
1.If your FVDI device has not yet been locked,please update the Quick
Loader to v7.0 as soon as possible.After updating the Quick Loader,you
can run the FVDI correctly.Quick Loader v7.0 Download:
https://mega.nz/#!WAglGaTB!t-JvU38sWLrw4CEmpidu0TZzkNbhGGsLweAbYOrb-Yw2.If you FVDI has been locked,you need to send the main unit to FLY
factory for repairing.And you need to pay $50 for unlock service and
shipping cost.3.And if you would like to send the device back to factory for
repairing,you would like to choose pay for extra money to get the Newest 2018 version FVDI (never locked version)
FVDI 2018 2015 FVID2 Installation Step by Step Guide
And there is the last choice to repair this problem by yourself,but you need to try it at all your risk.We don't take responsibility for the result!!!
This solution is share on DK forum by the member.1.) FVDI V2015 or higher with softdog versions:
If the pc cannot detecting any fvdi's then the LPC1788 processor was
erased ( the Quickloader v6.3 will erase the LPC processor ).
always erasing are the following two address: 0x00000000-0x00047FFF or 0x00000000-0x0007FFFF(click to enlarge)
After the FVDI died because there are no has a BOOT sector and the some firmware rows.
2.) if you cannot bought any FVDI's from FLY Company, then the pc will
go to internet then always erasing all FVDI LPC processors by FLY server
!!!!!
3.) I solved all algorithms to fvdi firmware encrypting/decrypting and now i looking the 8bytes key to v2015 version.
UOBDII All rights reserved How to Solve FVDI 2015 2016 Locked Error
How to renew/ virgin used Toyota smart key by CN900 MINI?
Do you know it's easy to reuse an old matched Toyota smart key? Below
you will know: How to renew/ reprogram/ virgin a used Toyota smart key
by CN900 MINI key programmer?
Smart CN900 Mini Tech STEPS:
CN900 MINI renew Toyota smart key with 74 chip
Power on CN900 MINI, it will show main menu including "Read & Copy", "Test Frequency", "Special" and "Setup".Choose "Special" function then "Smart Key".Follow the instruction: Put the used Toyota smart key into the transponder area (the coil as picture).Click "Clear Byte" and "Yes" to confirm.Wait a minute and don't move the key, the original key data will be erased.In this way, you use CN900 MINI to renew and virgin an old used Toyota smart key successfully! Now a new working Toyota smart key with blank key chip is ready!
Source:How to renew/ virgin used Toyota smart key by CN900 MINI?
How to Update & Active/Add Tokens for Autek IKey820 Programmer
This article show a guide on how to update,active/add tokens for Autek IKey820 Programmer.
Preparations:
1Autek IKey820 Key Programmer
2PC with Win10/Win8/Win7/XP
3USB cable
4 Autek IKey820 Update Tool V1.5Install Update Tool on Your PC
If the update tool "Autek IKey820 Update Tool V1.2" is already installed
on your PC before,just skip this step.If not,you need to install it.
Run "Autek Ikey820 Update Tool v1.5.exe"Note:The update v1.2 need installation,but for v1.5 you can run it directly
Autek IKey820
Update Tool contains three parts including update,active and message from top to bottomUpdate Autek IKey820 Key Programmer:
Take the following steps to update Autek IKey820 device:
1.Connect IKey820 to PC via USB cable
2.Open Autek IKey820 update tool on your PC(Your PC need to connect on Internet)
3.Select the device in list and input the SN (usually completed automatically)
4.Click Update button to start updating,wait until the updating completed.There is something you need to notice in each step.
1) The device should display "USB SD DISK MODE" when connected to PC
through USB cable, if not, please unplug the USB cable and plug again.
Do not unplug the USB cable or exit from USB SD DISK MODE.
2) If AUTEK IKEY 820 Update Tool is not installed, please install it first, see detail in chapter 2.
3) The DISK and SN should display automatically if the device is
connected to PC. If the DISK has no device to select, please unplug the
USB cable and plug again. If the DISK has been selected, but SN is
empty, please unplug the USB cable and plug again. If it's still the
same, please input SN yourself. The SN should start with "A-".
4) It may take several minutes to update, it depends on the speed of your internet.If there is any problem, it will display on message area, check according to the message and try again.Here are the pages for updating. The SN is just an example, you should use your own SN.
Check SN and DISK before updating.Wait until update successfullyUpdate successfullyActivate/Add Token
Activation means add tokens to your device. If your device runs out of
tokens or you want to increase the number of tokens, you can use AUTEK
IKey 820 Update Tool to increase tokens.
Take the following steps to activate AUTEK IKey820 device:
1) Supply power to the AUTEK IKey820 device through USB/12V DC adapter/OBD.
2) Go to the ACTIVATE menu, you will see a page with steps to activate
your device and the REQ CODE which is need in AUTEK IKey820 Update Tool
to get the ANS CODE.
3) Open AUTEK IKey820 Update Tool in your PC.
4) Input the REQ CODE to the AUTEK IKey820 Update Tool and click ACTIVATE button, then you will get the ANS CODE
5) Press OK button on the device and there display the page to input ANS CODE
6) Input the ANS CODE you get in the AUTEK IKEey820 Update Tool. There are two different
7) Press OK button and the page will show the result, SUCCESS or FAILED.
8) You can check your tokens in the ABOUT menu if you activate your device successfully.Here are the pictures to activate the device. All the SN、REQ CODE and ANS CODE are examples, just ignore them.
Select the ACTIVE menuThe ACTIVE pageOpen Autek IKey820 Update Tool and input the REQ CODEGet the ANS CODEInput ANS CodeConfirm the ANS CODE you inputSucceed means active successfullyCheck the token in About page
Article from:https://blog.uobdii.com/autek-ikey820-updating-and-activation-guide/
How to Use Digimaster 3 to Decode Mercedes Benz Audio?
When the vehicle audio was power off because of battery damage, the audio will start the anti-theft system automatically-UOBDII.com remind you. So here I want to share you how to use Yanhua Digimaster 3 to decode audio for Mercedes Benz.Digimaster III
can calculate the audio code out or initialize it, as the following
picture shows, Digimaster 3 has the function of " Audio decoding" ,
after click it, you will find it supports decoding audio for Alfa, Audi,
Benz, BMW, Ford, gm, Honda, Lexus, mazda, Mitsubishi, Peugeot, Porsche,
Renault, Toyota, Volvo, Volkswagen and more.2. Audio Code Management
Step 1: Select Benz to decode, and de-solder the corresponding chip according to the software prompts. Click "Next" to begin decoding.
Step 2: remember the code in the pop-up dialogue box, click "Next", the code was written in the chip.
Step 3: Solder the chip back to the board, and then use this new code to decode the audio.3 Address Code
These models only need to short-circuit some welding spot to reset the code, the software will give a specific method.
UOBDII All rights reserved Mercedes Benz audio decoding using Digimaster III at November 29, 2018 Email ThisBlogThis!Share to TwitterShare to FacebookShare to Pinterest
How to Solve OBDSTAR X300M Security Verification Failed Trouble
When used the OBDStar X300M to do odometer correction function on OPEL Astra 2010, it come out the error "Security Verification Failed",How to solve the X300M security verification failure ?
When it fails to communicate or program, please operate as below:
1.Connecting x300m - Starting it-Pressing option-Pressing Data Logging-Pressing on-Pressing ESC - Back to the main menu.
2.When it fails to program, power off the machine please.
3.Pull our TF card where there is a LOG file.
4.Send us the LOG file and the engineer would study the data and figure out the reason.
From OBDSTAR Tools Technical Official Blog, post Solution to OBDStar X300M Security Verification Failure
How to Solve XTOOL PS2 Error "failed to download mcu.bin to the vci"
Provide solution to the xtool ps2 heavy duty trucks error " failed to download mcu.bin to the vci".Solution:
you have wired and wireless communication
please turn off wired connectionPlease follow the guide on how to connect Xtool PS2.The obd connectorThe GDS VCI readerConnect the OBD connector to the VCIfix them firmlyFollow the connection diagramPlug the obd connector to the car.The indictor turns red.Turn on the Xtool PS2 scannerBoth the scanner indicator and VCI indicator turn green, which means they are working normally.Finally, the function menu display, you are ready to perform:
Diagnose, immobilizer, mileage adjustment, TPS, maintenance reset,
electronic park brake and more incl. ansmission, Steering angle, Tire
pressure loss alarm (activated) and other common special functions.www.xtooleshop.com
Article from:https://xtool-tool.over-blog.com/2018/11/how-to-solve-xtool-ps2-error-failed-to-
VVDI Prog and Xprog is Best Choice for Fresh Man
If you are a beginner of VVDI Programmer, you don't need the adapters, if you need to read eeproms, get a second programmer like Xprog 5.55.And for many auto locksmiths,it is important to choose a suitable programmer,here i put it here:
https://www.uobdii.com/wholesale/auto-key-programmer/
Why another programmer? Is not good with eep?
Xprog is cheaper then a vvdiprog adapter.
vvdi prog is good for reading proccesors.
Some have had problems reading eeproms.
This might be solved now that there is a adapter.
If your vvdiprog fails, at any reading or programming, you will have a backup.
It also helps as a confirmation to solve some reading writing problems.
All my collegues have at least few laptops, w7 32 w7 64 and xp.
And xprog, upa, tl866, willem, orange5
Xprog, is a great tool, and comes with many adapters.
Some even sell a xprog clamp adapter, to make i even more handy to use.
The picture posted, is 17euro adapter to use on xprog.
UOBDII All rights reserved Why vvdi prog + Xprog is needed for a beginner?
Car Key Programmer:Automotive Locksmith Handheld Choice!
The following parts list the most popular hand-held car auto key programmer for all makes which best for professional locksmiths. They are SBB Pro2,Smart CN900 Mini, CK-100 and Original X-100+. SBB Pro2 V48.88 Programmer:Now SBB PRO2 Key Programmer Updated to V48.88 Version.support new cars
to 2017.12. like for Acura 2017, Chevrolet 2017,Buick 2017, Cadillac,
GMC 2017, Ford 2017,Dodge 2017,Toyota 2017...CK-100 Auto Key Programmer
- Newest generation SBB, compared with Silca Sbb, CK-100 auto key programmer newly add some models and even covers up to 2014. CK100 is available with 3 kinds of version, V99.99, V45.02 and v45.06.
- CK100 V99.99 can support Lexus RX350 07-09, SBB can't; CK100 V99.99 covers Lexus SC430 02-10, SBB only cover 02-06; CK100 V99.99 can do Corolla (CAN) from 2009 to 2012, SBB up to 09.
- CK100 make key by simply plug 16pin cable with OBD diagnostic socket, no need connect with computer. It can only communicate with the standard OBDII protocol vehicles. If your car is not standard 16pin connecter and not standard OBDII protocol, use T300.
- CK100 has 1024 tokens, after use it up, go to change a chip by following the seller's instruction.
CN900 Mini is the replacement of CN900 Key Programmer that can easily hand-held, which can easily update online as CN900.
- Smart CN900 Mini Transponder Key Programmer
- Support Online update
- Various types of vehicle anti-the fault detection, matching detection
- Portable Super long standby
- support four kinds of frequency 850/900/1800/1900MHZ
- Support 11/12/13/33/T5/4C/4D/42/46/48/72G chip copy.
- GSM/GPRS SIM
- USB2.0, Bluetooth4.0
Yanhua Mini ACDP Programmer:
XTOOL X100 Pad2 Read Peugeot 206 BSI Pin Code Test Report
This post will share you with the process on how XTOOL X100 Pad2 Pro read Peugeot 206 BSI pin code.
Use Tools:
Xtool X100 Pad2
Xtool EEPROM adapter
Connect X100 Pad2, eeprom adapter and bsi 95160 CPU chipSelect Read Pin CodeSelect EEPROM adapterMake sure the eeprom adapter is connected and powered on, the status indicator turns onselect car brand: Peugeot->206->BSI 95160select V1 or V2If have communication failed error, select another option or try againSave dataSuccessfully read Peugeot 206 BSI pin code by XTOOL X100 Pad2!Article from XTOOL
JLR Key Programmer
OtoSys IM100 Program Key for Volvo 2010-2016
AURO Otosys IM100 is verified to work with VOLVO immobilizer from the year 2010 to 2016.It's second to Lonsdor K518ise universal key programming tool that support VOLVO.
https://www.obd360.com
Step 1: learn keys
AURO Otosys im100 tested with Volvo immo...
Otosys IM100 Volvo car list:
Volvo S60, S80, V40, V60, V70, XC60, XC70
semi-smart keys 2010-2016
Keyless CAN systemAuro IM100 begins to program new semi-smartkeys to Volvo when all keys are lostIf you want to continue to performing this function, there must be one key!
The original key, if cleared successfully, needs to be learned again
Please verify the type of the key first
Ignition off
Learned keys: 2
Step 2: decrypt the immo & clear all keys
The immobilizer unit is to be decrypted, which may last a few hours.
Please make sure that the ignition is turned off
You can exit this process at any time and continue from the interruption point in the next operation
Decrypting the immobilizer unit...
The procedure will take 0-8 hours due to the difference between vehicles.
You'd better manually close the center-control LCD, lamp, etc. Toreduce the power consumption
It doesn't matter whether the door is opened or closed
You can exit this process at any time and continue from the interruption point in the next operationDecrytion successOtosys im100 is reading security data
Don't disconnect the OBD connectionCopy CEM security data successfullyAll key cleared! Learned keys: 0
Step 3: learn keys
Key learning successIgnition off OBDSTAR
Remove the key from the key slotLearned keys: 4
UOBDII All rights reserved How to Use OtoSys IM100 to Program Key for Volvo 2010-2016
How to solve can't find erase password vvdi mb for eis w204
Recently,OBD2 customers feedback VVDI MB error "can't find erase password",so here OBD360 engine share the method to solve this problem.Q: I would like to use VVDI MB tool to renew eis A204 545 13 08 because the esl is damaged, I unlocked the ESL now I need the renew for can personalized.
I can't find erase password for renew this one.A: You don't need to renew eis
just make password calculation from eis
then save eis data with key pw !
after u unlock esl nec chip just load vvdi mb eis data and
take this eis data with pw you just saved and just make a click on "auto
tp clear and personalize"
THATS IT!
Mercedes Benz EIS Trouble Repair Guide
Q: I do not know this procedure. After I need write eis data in ESL ?
A: yes mate just write ur eis data included key pw in esl nec !
**important** make a click on "auto clear tp and personalize"
THEN
write esl!
Q: I can't write.
I have error ? writing data failed ?.
I can use ESL emulator ?
A: Yes you can use elv emulator.UOBDII All rights reserved (Solved) Can't find erase password vvdi mb for eis w204
How to use Defu 368A key machine makes double sided flat keys?
Defu 368A is a very cheap machine, but does cut most keys well with clamp addons for tibbe etc.
DOES NOT DO "all keys lost"
Ok for doing double sided flat keys buy a universal key clamp and cut it up as in picture 1. (universal clamp won't do these keys)
drill 2.5 mm holes for clamp screws and use 3mm tap to run threads picture 2.
cut some shims from the supplied steel shims picture 3.
Pictures 4 and 5 perfect working key
brilliant machine for the money.XTOOL
FYI, Aliexpress or ebay "universal key clamp" should get you started.First test here all good work perfectly.Xhorse iKeycutter XC-Mini
For Defu 368A vertical key machine, you can go for:
https://www.uobdii.com/wholesale/368a-key-cutting-duplicated-machine-200w.html
Article from:Defu 368A vertical key machine makes double sided flat keys perfectly
XTOOL X100 Pad2 BMW Key Programming Feedback
Recently, one customer got his new XTOOL X100 Pad2
but he is sad to find that this pad can't work! He uses this pad2 to do
BMW Key programming but fail. What happen? Let us find out why and
solve this problem.
Here attach an image to express his situation:Customer: This weekend I tried a Q7 2006 to diagnose the pneumatic
shock absorbers the aircraft supports only 5 marked so Jaguar, land
rover, Benz and another brand. And my BMW 3 series E91 for DPF system
(the fap) because I have the light FAP lit nothing it does not work.
Today I tried to program a key on a Golf 2000 gasoline and I can not,
I try to make a BMW e46 it does not work either. I would like to have
the procedure to follow !!! Please, thank you in advance
https://www.obd360.com
Engineer suggest customer change the menu from "F chassis and E chassis" to "CAS 1-3"While customer still can't do BMW key program after using the "CAS
1-3". And it appears a "Fail to communicate" and a CAS 1-3 using note:
Here are some tips to use XTOOL X100 Pad2:
- Choose the right menu or change the menu when you meet problem programming.
- Update the device to the latest version software.
- If the X100 Pad2 still can't work after update, you could tap the "Help" on the device to test the device so that the engineer could give you more detail solution.
If you have any problem when using XTOOL, please contact us.https://blog.uobdii.com
OBDSTAR H110 Customers Feedback: Work perfect
OBDSTAR H110 VAG key program & KM change Feedback, most users test it works perfectly.
- Dash Touran 10/2014 ok
- Skoda Fabia 12/2016 Mileage change works.
- OBDSTAR H110 good tool i have made a key for vw polo and vento working fine and for km also good.
- VW Sharan 2015 km change ok
- MK7 Golf Yes
- Audi A4 2014 Key program ok
- Skoda Fabia 12/2016 Mileage change works.
- VW Sharan 2015 km change ok
- Т5 - 2014. Ok
Т6 - 2017. Ok
Fabia MQB 1016. Ok
Golf 2015 1.4. MQB Ok
- support lost keys for VW group as long as the IMMO is not higher than 4th generation.
- Passat B6 2008 cdc km correction okay.
- Skoda Superb 2010 immo area read okay.
T5 2012 immo area read okay.
- Sharan 2014 color display
eeprom read okay
immo area read okay
km correction okay.
Best place to buy obdstar H110 from:
You can buy from this shop:
https://www.obdstartool.com/wholesale/obdstar-h110-vag-i-c-for-mqb.html
Vident iSmart900 Manually Locate a Required Control System
This article show you to how use Vident iSmart900 to locate a required control system manually for testing through a series of choices.Simply follow the menu driven procedure, and make proper selection each time; the program will guide you to the diagnostic function menu after a few choices you've made.
To select a system for testing:
1. Select Control Unit from the menu and a controller menu displays.
2. Select the system you would like to test. When the scanner has
established connection with the vehicle, the Function Menu displays.
source:https://www.uobdii.com/wholesale/vident-ismart900-automotive-diagnostic-analysis-system.html
Vident Tech Article from:Vident iSmart900 Manually Locate a Required Control System
How to Solve XTOOL X100 Pad2 Data Load Fail
One XTOOL X100 PAD2 users turned to us that when he tried to tap the car models of X100 PAD2, the error will appear with the note that "fail to load data". The version of his xtool x100 pad2 app is V3.1.5.
The error shows as below:Solution:
- Reset XTOOL X100 Pad2 to factory settings (the reset button is in the setting)
- delete the file call "XTOOL"in the nand flash
- Reinstall the XTOOL X100 Pad2 app
https://mega.nz/#!VKAEHDDD!jejp460R0AANnr_S__q7cFIazW1pIQ_Ja_PNcOSmyRM
Article from:How to Deal with XTOOL X100 Pad2 Fail to Load Data
OBDSTAR X300 DP Plus Clone ECU for GM Opel Bosch BCM
This article show a guide on how to use OBDSTAR X300 DP Plus to
clone GM Opel Bosch BCM.You can copy the original ECU data,and then
write the data into another same ECU hardware via X300 DP Plus,so that
it can achieve the same function as the original ECU.Let's jump right
in!Procedure:
Select "ECU Clone"==>GMGM V30.01,and tap "OK"Select "Auto" and tap "OK"It prompt with the information "This function is available by
connecting the server,please ensure the Internet connection is normal"
Tap "OK" to continueSelect "Read EEPROM",and click "OK"Enter a filename to saveFile saved successSelect "Read FLASH"Enter a filename to saveClick "Write EEPROM"Select the data file you saved beforeLogging system...
Restoring EEPROM...
Successful data recoverySelect "Write FLASH"There are certain risks in operating this function.Does it continue?
Remember:During operation,make sure that the vehicle is fully powered and do not disconnect the device.Tap "OK" to continueSelect the FLASH file you saved before,then tap "OK" to continueLogging system...
Restoring FLASH...
Successful data recoveryDone!
Src:https://www.obdstartool.com/wholesale/obdstar-x300-pad2-full-version.html
From OBDSTAR Tools Technical Official Blog, post OBDSTAR X300 DP Plus Do GM Opel Bosch BCM Clone
FVDI J2534 download and install on win7 8 10
FVDI J2534
features in Ford Mazda IDS diagnosis and online module
programming, meanwhile it is tested OK to work with Ford IDS V110, Mazda
IDS V108, Toyota TIS V13.00,
Honda HDS V3.102, Land Rover/Jaguar SDD2 V153, Nissan CONSULT III
plus R2R V80.11. It is fullly compatible with SAE J2534-1 and partly
compatible with SAE J2534-2.
It is better than many J2534 interfaces.
FVDI J2534 Interface package:
The USB is for communication with the computer, the CD is packed with driver.Compatible software for J2534:
Ford IDS V110
Mazda IDS V108
Toyota TIS V13.00
Honda HDS V3.102
Land Rover/Jaguar SDD2 V153
Nissan CONSULT III plus R2R V80.11FVDI J2534 software & driver Installation on win7:
USB communication
OS: Win7(64bit), Win8, win10
CPU: Pentium 3/1GHZ~ Pentium4/1.8GHZ or above
Memory(RAM): 256M ~ 512M or above
HDD: 40G ~60G or above
Display: 800×600 ~ 1024×768 or above
USB interface: One or moreNote: The compatible software can't be installed in the same computer.1.Browse https://flyobd.com/shop/download-center/, register a member and login to download the compatible software that you need i. Ford IDS.
- Copy the driver in the packed CD and paste it to the computer.
- Install the driver and then FVDI J2534 software.
Double-click the "IDS-110.01_Full.exe" to start installation
Select language, and click "next" buttonWait a while, and the following windows will pop out, click "Yes", then click "next"Select "i accept the terms of the license agreement", and then click "next", and then
click "next", and then click "install". The installation process will take some time, please
wait patiently.Reboot your computer after installation2): Install the FVDI J2534 software
Open compact Disc and find FVDI-J2534 software and double-click the
"FVDI_J2534_Ford_Setup.exe" softwareSelect Setup Language and Click "Ok".It will install SVCI Based software list, Click "next" directly, and then Click "next" all the
time until it jump a window "Select Setup Language", which is selected the device
driver's installation language.Install the device driver, and click "Next" all the time until install Shield wizard complete,
and then click "finish".When you open FVDI J2534 for ford software after installation, an error window will pop
out. That means you have not connect FVDI J2534 equipment with your computer, as
show in the below. connect your device with computer, and the FVDI J2534 software will
be opened normally.When you put FVDI J2534 equipment to connect the computer and open the software,
it will pop below error message, it means you do not connected vehicle ECU module and
the ECU voltage cannot less than 8 volts. After using the OBD interface of FVDI J2534 to
connect the ECU, and the software can be opened normally and put into use.Note: Cannot open the IDS software on the desktop directly, it is recommended to delete
FVDI J2534 download and install on win7 8 10
FVDI J2534
features in Ford Mazda IDS diagnosis and online module
programming, meanwhile it is tested OK to work with Ford IDS V110, Mazda
IDS V108, Toyota TIS V13.00,
Honda HDS V3.102, Land Rover/Jaguar SDD2 V153, Nissan CONSULT III
plus R2R V80.11. It is fullly compatible with SAE J2534-1 and partly
compatible with SAE J2534-2.
It is better than many J2534 interfaces.
FVDI J2534 Interface package:
The USB is for communication with the computer, the CD is packed with driver.Compatible software for J2534:
Ford IDS V110
Mazda IDS V108
Toyota TIS V13.00
Honda HDS V3.102
Land Rover/Jaguar SDD2 V153
Nissan CONSULT III plus R2R V80.11FVDI J2534 software & driver Installation on win7:
USB communication
OS: Win7(64bit), Win8, win10
CPU: Pentium 3/1GHZ~ Pentium4/1.8GHZ or above
Memory(RAM): 256M ~ 512M or above
HDD: 40G ~60G or above
Display: 800×600 ~ 1024×768 or above
USB interface: One or moreNote: The compatible software can't be installed in the same computer.1.Browse https://flyobd.com/shop/download-center/, register a member and login to download the compatible software that you need i. Ford IDS.
- Copy the driver in the packed CD and paste it to the computer.
- Install the driver and then FVDI J2534 software.
Double-click the "IDS-110.01_Full.exe" to start installation
Select language, and click "next" buttonWait a while, and the following windows will pop out, click "Yes", then click "next"Select "i accept the terms of the license agreement", and then click "next", and then
click "next", and then click "install". The installation process will take some time, please
wait patiently.Reboot your computer after installation2): Install the FVDI J2534 software
Open compact Disc and find FVDI-J2534 software and double-click the
"FVDI_J2534_Ford_Setup.exe" softwareSelect Setup Language and Click "Ok".It will install SVCI Based software list, Click "next" directly, and then Click "next" all the
time until it jump a window "Select Setup Language", which is selected the device
driver's installation language.Install the device driver, and click "Next" all the time until install Shield wizard complete,
and then click "finish".When you open FVDI J2534 for ford software after installation, an error window will pop
out. That means you have not connect FVDI J2534 equipment with your computer, as
show in the below. connect your device with computer, and the FVDI J2534 software will
be opened normally.When you put FVDI J2534 equipment to connect the computer and open the software,
it will pop below error message, it means you do not connected vehicle ECU module and
the ECU voltage cannot less than 8 volts. After using the OBD interface of FVDI J2534 to
connect the ECU, and the software can be opened normally and put into use.Note: Cannot open the IDS software on the desktop directly, it is recommended to delete
the IDS software shortcut on the desktop.Source: https://www.uobdii.com/wholesale/fvdi-j2534.html
VVDI MB Tool All Key Lost Programming for Benz W210
our dream comes true! !! Mercedes Benz W210 all keys lost has solution, that is the newest version VVDI MB V4.1.0 plus one Power Adapter. This post goes for the details and instructions.VVDI2 Programmer
Let's start with VVDI MB V4.1.0 newest update:
2018-07-13
*** Require firmware V4.0.0
************************************************************************
===== BENZ V4.1.0 =====
1.This update no need update the firmware
2.Password calculation: Support calculate password for W202/W208/W210(KLine) EIS
a.No more need MCU's de/soldering, very safe and quickl
b.Support add key and lost all key for password calculation
c.The procedure require about 25-30 minutes
d.The procedure need MB Power Adapter support
e.The procedure should work on the bench, not on car
3.Bugfix for load motorola EEPROM dump file in EIS window
4.Bugfix for activate BE key
5.Bugfix for read EIS W209
6.BugfixHow to make key for W210 all key lost using VVDI MB?
2. Images + words instruction:
Connection of VVDI MB and power adapter:Password calculation in 4 steps:What is the purpose of this MB power adapter?
1.Mercedes-Benz power adapter can be used in the FB3 system all lost and gateway simulation, works: class C, E, CL, CLK, MK, GL, GLK and other models.
2.Use the Mercedes-Benz power adapter to collect W210 W204, W207 all lost, only need 18 minutes. If
you don't use the Mercedes-Benz power adapter, it will take about 150
minutes. VVDI MB power connector will help you save nearly 2 hours.
3.Use VVDI MB Tool power adapter to collect W210 W216, W164, 2009 + all lost, do not need to plug the infrared adapter. If without the Mercedes-Benz power adapter needs to plug 500 times, this adapter help you operate easily.
4.Support gateway simulator function, without the gateway, you can get access to W210,W164, W164 2009 +, W209, W211 (need to use dedicated linear beam cable) directly by OBD way.VVDI Key Tool https://www.keycuttingmachine.org
How to Solve XTOOL X100 Pad2 Data Load Fail
One XTOOL X100 PAD2 users turned to us that when he tried to tap the car models of X100 PAD2, the error will appear with the note that "fail to load data". The version of his xtool x100 pad2 app is V3.1.5.
The error shows as below:Solution:
- Reset XTOOL X100 Pad2 to factory settings (the reset button is in the setting)
- delete the file call "XTOOL"in the nand flash
- Reinstall the XTOOL X100 Pad2 app
Article from:How to Deal with XTOOL X100 Pad2 Fail to Load Data
Different Between OBDSTAR H108 and F108?
Some customers sent email to ask me about different between OBDSTAR H108 and OBDSTAR F108,so here obdstar engineer give the comparison below:
OBDSTAR H108 is update version of OBDSTAR F108,it can do more PSA vehicle model and newest year models.
obdstar H108 and obdstar F108+ comparison table
obdstar H108 obdstar F108+
Image
Price $235 free shipping $135 free shipping
PEUGEOT Yes Yes
CITROEN Yes Yes
DS Yes Yes
K-line old cars Yes Doesn't work with the older cars especially the ones before 2008 year.
Canbus newer cars Yes Yes, some users tested it working with 2017 car models
OBD Key programming Yes Yes
OBD Pin code reading Yes,read Pin code when all keys lost Yes
Cluster calibration Yes, much better than F108+ Covers Less vehicles than H108
Language English English
Update Online update via TF card for 1 year free Online update via TF card for 1 year free
Warranty 1 year 1 yearobdstar H108 wins obdstar F108+ in:
PSA Support List Automatic
IdentificationRead
PincodeRead
EEPROMWrite
EEPROMRead
FLASHCluster Calibrate
SIEMENS D76F0018+95160 K LINE(BSI-E0X-00/BSI-F0X-00) √ √ √ √ × √
SIEMENS 1L00M+95128-95256CAN(BSI-SOX-00) √ √ √ √ √ √
CONTINENTAL SC667050+95256 CAN(BSI-Q0X-00) √ √ √ √ √ √
JC easyCAN4+29LV400BB+95128 CAN (BSI2004-HOX) √ √ √ √ √ √
JC easyCAN4F1M-32+95128 CAN (BSI04EV-K0X) √ √ √ √ √ √
JC SPC560B60+95128 CAN (BSI04EV2-KEX) √ √ √ √ √ ×
VALEO 2M48H+24C128 CAN (BSIEV-X0X-00) √ √ √ √ √ √
VALEO 4L00M+95128-25128CAN(BSI2004-POX-00) √ √ √ √ √ √
VALEO SC667152+95256 CAN (BSI-NOX) √ √ √ √ √ √Article from:https://blog.obdstartool.com
XTOOL PS90,XTOOL PS80 and AutoProPad,Which is Better?
Xtool PS90, PS80, AutoProPad and AutoProPad Lite are almost the same and different in some aspects.1.Functionality:
Xtool PS90,XTOOL PS80 and the AutoProPad/Lite:All Units have the same functionality incl.
diagnosis on a wide range of car models, special functions (eeprom, ecu
reset, GAS, Hang, light, ostbms, EPB, TPS, TPMSRESET), EPS for American
/ Asian / China-made/ European cars, Immobilizer for many cars, mileage
adjustment, service light reset etc.
The king would be the PS90 because of the hardware and its ports.2.Coverage:
There are 3 firmware 1.PS90>>2.PS80>>3.autopropad all
three have the same coverage. The lite came out in February to have a
lower cost tablet. That tablet comes with less coverage, no camera, no
kc100.
3.Update:
Frequently Free update online
Firstly browse official site https://www.xtooltech.com, click on "Service & support", then "Update Notice" (Most are PS90) as well as "Download update tools".
It's second year and no upgrade fees have been collected as of yet.
Xtool Company have tried their best to make the tool better.
4.Price:
The price has difference between Xtool PS90/80 from china and the US.
Xtool PS90 (China) sales for about 1300USD free shipping, shipped by DHL.
Like: www.uobdii.com/wholesale/xtool-ps90-diagnostic-tool.html
Xtool PS90 amazon: 1300USD
Xtool PS90 aliexpress: 1300USD
5.Language
English and Chinese Regardless, Xtool tools especially PS90 is a great machine to have, saves a lot of AD tokens, I'm happy with it.
UOBDII All rights reserved Xtool PS90 VS PS80 VS AutoProPad / Lite
Jaguar XJ Check Engine Light On Repair Guide
A 2006 Jaguar XJ sedan with a mileage of approximately 110,000 km and a
3.0 L V6 engine. The car was inspected and repaired due to the engine
failure light.JLR SDD Mangoose
Another issue:
Jaguar XK / XKR ( X150 ) Passenger seat recline Repair
Troubleshooting:After the vehicle is picked up, the test is verified to be faulty, the
ignition switch is turned on, the engine is started, the engine is
started smoothly, and the engine fault light on the instrument panel is
lit, and the fault phenomenon does exist. Connect the fault detector and
retrieve the fault code. The fault code is "B2139 Data mismatch
(received data does not match expected data)", which means that the
password does not match; "P0171-00 System too lean (bankl)", The meaning
is that the cylinder group 1 is too lean; "P0174-00 System too lean
(bank2)", which means that the cylinder group 2 is too lean; "U1262 SCP
01850" Communications bus fault", which means SCP U1850) bus
Communication failed.
Analysis of the fault code shows that the fault codes associated with
the fault phenomenon are P0171 and P0174. The relevant data stream is
read. The data flow shows that the long-term fuel correction values of
cylinder groups 1 and 2 at idle are 20.3%, the short-term fuel
correction value of cylinder group 1 is 3.91%, and the short-term fuel
correction value of cylinder group 2 is 5.47%. . However, when the
accelerator pedal is depressed, the engine speed is increased. As the
engine speed increases, the long-term fuel correction values of the
cylinder groups 1 and 2 gradually return to normal, but the short-term
fuel correction value of the cylinder group 2 is always larger than that
of the cylinder group 1.According to the above inspection results, combined with the maintenance
experience, it is considered that there is a high possibility of
leakage in the engine intake line. Considering that the short-term fuel
correction value of the cylinder group 2 is always larger than that of
the cylinder group 1, it is suspected that there may be a leak in the
intake line on the side of the cylinder group 2. Then, the intake line
on the side of the cylinder group 2 is inspected, and it is found that
there is a leak in the intake switching valve on the side of the
cylinder group 2. However, according to the maintenance experience, the
leakage of the pipeline on this side does not make the long-term fuel
correction value of the whole system significantly higher.Next, the maintenance personnel inspected the activated carbon canister
solenoid valve and found that the activated carbon canister solenoid
valve was still open at idle speed. Disconnect the pipe connected to the
activated carbon canister at the throttle valve, and grasp the
interface on the throttle side by hand to observe the change of the
long-term fuel correction value of the cylinder groups 1 and 2 at the
idle speed, and find the long-term fuel of the cylinder groups 1 and 2.
The correction value has changed to 18.8%. Although it has improved
better than the previous test results, the air leakage fault has not
been completely eliminated.Check the various ports of the pipeline between the air filter and the
intake manifold, no air leakage, and check the brake vacuum tube, the
crankcase forced ventilation line, the fuel pressure regulating valve
vacuum line and the activated carbon canister solenoid valve vacuum
tube. Road, no abnormalities. Troubleshooting is deadlocked.After careful consideration, the fault apparently has air that has not
been counted in, causing the system to correct the amount of fuel
injected. The maintenance personnel again inspect the intake line again.
When the air cleaner was removed and the intake line between the
throttle and the throttle was inspected, it was found that the back of
the intake pipe was aged and cracked.
Troubleshooting: Replace the intake line and cylinder group 2 intake switching valve, commissioning, troubleshooting.
Crack JLR SDD V151 free download on Win7 8 10 - No pass
How to use EUCLEIA TabScan S7 Reset EPB for Audi A8 2011
Here comes the guide on how to reset EPB for Audi A8 2011 by EUCLEIA TabScan S7.Hope it helps!
Vehicle Information:
Audi A8 2011
Manufacturer:Audi AG Neckarsulm
VIN:WAURGB4H3CN0****
Type:A8L 3.0 TFSI quattro
Products for Operation:
EUCLEIA TabScan S7
EUCLEIA TabScan S8
Procedures:Connect EUCLEIA TabScan S7 to vehicle and enter the "Service" menu to select "EPB Reset"Select "Audi"-->"A8"Select "A8(D3)"
Select "Replacement of brake pads"According to notes to release handbrake, then click "Yes", at this time
the rear brake pump motor will be heard for a few seconds to be
retracted. After the retraction is completed, install the new brake pad
according to the notification, then click "ok".The brake pump is released,please wait...
Lease replace brake pad for the two rear wheels!At this time rear brake pump will ring for few seconds, after the branch pump is released , click ok.Replace brake pad success!
All operation completed, quite system,
press electrical handbrake button to make handbrake work, reset EPB completed.
Please exit the system,turn off and then turn on the ignition switch,completed.
Notes:
Please do remember release the handbrake once Reset EPB.
Article from EUCLEIA TabScan S7 S8 Tech,How to use EUCLEIA TabScan S7 Reset EPB for Audi A8 2011
How to Use Vident iLink400 to Read I/M Readiness Status Data?
Vident iLink400 I/M Readiness option allows to view a snapshot of the operations for the emission system on OBDII/EOBD vehicles.I/M Readiness is a useful function used to check if all monitors are OK
or N/A. The vehicle's computer performs tests on the emission system
during normal driving conditions. After a specific amount of drive time
(each monitor has specific driving conditions and time required), the
computer's monitors decide if the vehicles emission system is working
correctly.
When the monitor's status is:
OK - vehicle was driven enough to complete the monitor.
INC (Incomplete) - vehicle was not driven enough to complete the monitor.
N/A (Not Applicable) - vehicle does not support that monitor.
There are two types of I/M Readiness tests:
Since DTCs Cleared - shows status of the monitors since the DTCs were
last cleared.This Drive Cycle - shows status of monitors since the start
of the current drive cycle.
There are two ways to retrieve I/M Readiness Status data:
One-click VIDENT iLink 400 I/M readiness key
Typical way: select I/M Readiness from Diagnostic Menu
To retrieve I/M Readiness Status data by one-click I/M readiness key:
1. Press the One-Click I/M Readiness Key on the keypad and the following screen displays.2. Colored LED and build-in beeper provide both visual and audible
reminders for emission check and DTCs. Below is the interpretation of
the LED and build-in beeper.
When the LED is :
$ Green - Indicates that engine systems are "OK" and working properly
(the number of Monitors equipped with the vehicle which have run and
performed their self-diagnostic testing is in the allowed range. MIL is
off. ).No stored and pending DTCs exist. The vehicle is ready for an
Emissions Test.
$ Yellow - The tool finds a possible problem. It indicates the following two conditions:
(1) Pending DTCs exist. Please check the I/M Readiness test result screen and use the
Read Codes function to view detailed codes information.
(2) Some of the vehicle's emission monitors have not working properly. If the I/M
Readiness screen shows no DTC (including pending DTC), but the Yellow LED is
still illuminated, it indicate a "Monitor Has Not Run" status.
$Red- Indicates some problems exist with one or more of the vehicle's
system, and the vehicle is not ready for an Emissions Test. As well
there are DTCs found. The MIL lamp on the vehicle's instrument panel
will light steady. The problem that is causing the illumination of Red
LED should be fixed before an Emissions Test or driving the vehicle
further.The built-in beeper works with the colored LED simultaneous, as an assistance to reflect the I/M Readiness test results:
Green - two long beeps.
Yellow - short, long, short beeps.
Red - four short beeps.
To retrieve I/M Readiness Status data :
1. Scroll with UP/DOWN key to highlight I/M Readiness from Diagnostic
Menu and press the OK key. If vehicle supports both types of monitors, a
screen for monitor type selection displays.
Select a monitor type and press the OK key.
2. If the vehicle is tested supports both types of monitors, following screen displays.3. Depending on readiness test, one of these 2 screens will be present.
Use the up and down arrow keys to scroll through data. Press the ESC key
to exit.or
Source from VIDENT,How to Use Vident iLink400 to Read I/M Readiness Status Data?
Different Between OBDSTAR H108 and F108?
Some customers sent email to ask me about different between OBDSTAR H108 and OBDSTAR F108,so here obdstar engineer give the comparison below:
OBDSTAR H108 is update version of OBDSTAR F108,it can do more PSA vehicle model and newest year models.
obdstar H108 and obdstar F108+ comparison table
obdstar H108 obdstar F108+
Image
Price $235 free shipping $135 free shipping
PEUGEOT Yes Yes
CITROEN Yes Yes
DS Yes Yes
K-line old cars Yes Doesn't work with the older cars especially the ones before 2008 year.
Canbus newer cars Yes Yes, some users tested it working with 2017 car models
OBD Key programming Yes Yes
OBD Pin code reading Yes,read Pin code when all keys lost Yes
Cluster calibration Yes, much better than F108+ Covers Less vehicles than H108
Language English English
Update Online update via TF card for 1 year free Online update via TF card for 1 year free
Warranty 1 year 1 yearobdstar H108 wins obdstar F108+ in:
PSA Support List Automatic
IdentificationRead
PincodeRead
EEPROMWrite
EEPROMRead
FLASHCluster Calibrate
SIEMENS D76F0018+95160 K LINE(BSI-E0X-00/BSI-F0X-00) √ √ √ √ × √
SIEMENS 1L00M+95128-95256CAN(BSI-SOX-00) √ √ √ √ √ √
CONTINENTAL SC667050+95256 CAN(BSI-Q0X-00) √ √ √ √ √ √
JC easyCAN4+29LV400BB+95128 CAN (BSI2004-HOX) √ √ √ √ √ √
JC easyCAN4F1M-32+95128 CAN (BSI04EV-K0X) √ √ √ √ √ √
JC SPC560B60+95128 CAN (BSI04EV2-KEX) √ √ √ √ √ ×
VALEO 2M48H+24C128 CAN (BSIEV-X0X-00) √ √ √ √ √ √
VALEO 4L00M+95128-25128CAN(BSI2004-POX-00) √ √ √ √ √ √
VALEO SC667152+95256 CAN (BSI-NOX) √ √ √ √ √ √Article from:https://blog.obdstartool.com
How to Register and Active Lonsdor JLR IMMO
Recently,Lonsdor company launch their newest product:Lonsdor JLR IMMO,special for JLR and Ranger Rover key programming.It's
designed to program car keys and applicable to above 95% of Jaguar and
LandRover models currently (VPW protocols of Jaguar's old model is
unsupported).(1) Please enter the site: https://u.lonsdor.com/jlrimmo/login① LoginUser who've bound Lonsdor product: input account, password and verification code to login.
auto key cutting machine
User who doesn't bind Lonsdor product: click【Register】and follow prompt messages to complete registration, then log in.② Bind device: after login succeed, check system prompts when device
boots. Input the device No. & registration code as per the prompts,
and set device password. Click 【Submit】to bind device.(2) After bind device successfully, enter the site: https://u.lonsdor.com① Click JLR-IMMO button, click【Get activation code】, confirm that device
No. shown on the webpage is consistent with actual device No.
Click【Submit】to get activation code.② Input device No. on webpage to the device to activate it.Article from: https://lonsdor-k518.blogspot.com/2018/07/how-to-register-and-active-lonsdor-jlr.html
How to Replace Battery for Autel PowerScan PS100?
Autel PS100 is a powerful electrical system diagnosis tool.Featuring AVOmeter, test light, built-in flashlight, short circuit
indicator, relay/component tester, continuity tester and bad ground
indicator, the PowerScan is truly the ultimate in power and
affordability, allowing users to check circuitry in one single step.Autel Tool
How to Replace Battery for Autel PowerScan PS100?
Remove the worn switch with a pry tool. Be careful when applying force.
Make sure to install the switch straight and press until flush with casing.It is recommended when buying you get two. This will fix your tool
now and give you a spare so you won‟t experience any down time in the
future.
src:https://www.uobdii.com/wholesale/autel-powerscan-ps100-electrical-system-diagnostic-tool.html
CGDI BMW Prog Program BMW F Series
This article show a guide on how to program BMW F Series by CGDI BMW Prog.
Procedures:
Open the doors and meters,connect CGDI BMW to vehicle by OBD.
Then run the BMW CGDI software and select "BMW F Series Program"Data was read successfully,display relevant module informationHere take FEM-Body programming as a example,click "Program"Please ensure that the battery has enough power and click "Yes"Make sure the VIN is correct
Support modificationProgramming,please be patientVerity FLASH correctly and program successfully
Src:https://www.cgdishop.com/wholesale/cgdi-prog-bmw-msv80-car-key-programmer.html
Article from:How to Program BMW F-Series by CGDI BMW
OBDSTAR X300 PAD2 Correct Odometer for Benz W169
Today Leo showed us how to use obdstar X300 DP Plus to
program mileage on Benz A169, please note, what he used is a testing
kit, in the real test, you need only use the OBDII cable to connect the
machine and the OBD port of the Benz instead of dismantle the dashboard.OBDSTAR X300 DP Plus
- Connection.
- Tap "Cluster calibration".
- Tap "Benz".
- Initial communication failed, please confirm that the diagnostic line is connected normally.
- Communicating successfully.
- Enter A series -> W169
- Switch ignition on.
- Reading mileage.
- Current mileage 8015KM.
- Please input the mileage of the adjustment.
- The dashboard will automatically turn off and on, means the machine is communicating with it.
From OBDSTAR , post OBDSTAR X300 DP Plus program mileage on Benz W169
BMW AK90+ II and AK90+ Programmer,which is better?
BMW AK90+ II compares BMW AK90+: both are the best BMW EWS key programmer; BMW AK90+ II update: add the key info reading function for new F series CAS4/CAS4+/and new Porsche, also the key renew functions for BMW CAS1-4.
Part 1: BMW AK90+ II Vs. BMW AK90+: the Differences
- BMW AK90+ IIUpdate:
New BMW F series CAS4/CAS4+/ new Porsche: adds key information identification function.Automobile fix
- The package: not the same
AK90+ with 10 pin cable (image 2).You can see the package includes one piece of AK90+ II Host, AK90+ II 6 Pin Cable, AK90+ II Chip data to read specific seat, AK90+ II software CD-ROM, AK90+ II USB communication cable etc.auto key cuttingAK90+ package includes AK90+ Host, 10 Pin Cable, AK90-Chip data to read specific seat, AK90 V3.19 software CD-ROM, AK90+ USB communication cable.Part 2: BMW AK90+ II Vs. BMW AK90+: the Similarities
- Best BMW EWS key programmer:
- functions : Same
- Directly reading data dumps from MCU which marked
1D47J,2D47J,0D46J,2L86D without removing MCU from circuit board,easy to
do yourself.
2. With the help of software you can change VIN,Mileage and renew, lock or unlock keys as well.
3. Programming original chips "EML 10030A" for making keys .
4. Identifying keys for all EWS ,showing VIN, key No. and mileage .
- Way:Same
- Language: English, Chinese
- OS:WinXP, Win7
Conclusion:
AK90+ II wins in functions.
AK90+ wins in Price (35USD only)
Article from:https://www.keycuttingmachine.org/bmw-ak90-ii-genupdate-version-of-bmw-ak90good-choice/
OBDSTAR X300 DP plus VS X300 DP VS Lonsdor k518ise
Post topic: obdstar X300 DP plus VS X300 DP VS Lonsdor k518ise in the software functions, vehicle coverage, features, hardware etc. And followed with obdstar X300 DP plus A package Vs B package Vs C package. Finally ends with obdstar X300 DP plus features & real pictures.
Part 1: obdstar X300 DP plus VS X300 DP VS Lonsdor k518ise
Software function Content OBDSTAR X300 DP Plus Lonsdor K518ISE OBDSTAR X300 DP Price $1699-$1999 (A package -C package) free shipping $1199 free shipping $829 free shipping Immobilizer system Key/Remote programming Yes Yes Yes EEPROM Yes Yes Yes Key Renew Yes Yes Odometer Correction VW Yes Yes Yes Porsche Yes Yes Yes Jaguar Yes Yes Yes Land rover Yes Yes Yes Mazda Yes Yes Yes Audi Yes Yes Yes Renault Yes Yes Yes Hummer Yes Yes No Hyundai Yes Yes Yes Kia Yes Yes Yes Besturn Yes Yes Yes Skoda Yes Yes Seat Yes Yes Benz Yes Yes Bentley Yes Yes Lincoln Yes Yes Chrysler Yes Yes GM Yes Yes Infiniti Yes Yes Mitsubishi Yes Yes Nissan Yes Yes Ssangyong Yes Yes Subaru Yes Yes Suzuki Yes Yes GreatWall Yes Yes Geely Yes Yes Fiat Yes Yes Citroen Yes Yes MG Yes Yes Rowe Yes Yes Baoteng Yes No Peugeot Yes Yes Opel Yes Yes Volvo Yes Yes Smart Yes Yes Alfa Romeo Yes No Ferrari Yes Yes Diagnostic Full system diagnostic Yes Diagnosis (Japanese and Korean Series) Special Functions Service reset Yes Manual remote control Yes Yes ABS bleeding Yes Yes Battery matching Yes Yes ECU programming Yes No EPB Yes Yes Throttle programming Yes Yes Airbag reset Yes Yes TPMS reset Yes Yes Steering angle reset Yes Yes OBDII Yes Yes DPF Regen Yes Yes Injector coding Yes Yes Suspension Yes NO Gear learning Yes Yes CVT learning Yes Yes Steering angle repair Yes ECU Clone Yes Switch activation Yes Hardware Test Frequency/ Yes Remote Tester Anti-theft Induction coil Yes P001 programmer unit Yes C001 circuit board Yes C002 circuit board Yes W001 data cable Yes W002 data cable Yes W003 data cable Yes Toyota smart key emulators Yes YesPart 2: obdstar X300 DP plus obdstar X300 DP plus A package Vs B package Vs C package
24C64
2014-key
programming. BMW (Standard) BMW (Advanced) √ √ √ Add FEM/BDC
key programming,
ISN code
reading etc. Volvo √ √ √ The other European cars √ √ √ Asian cars Hyundai /Kia (Standard) Hyundai /Kia (Advanced) √ √ √ Add 47/8A/46 smart
key pin code
reading Toyota /Lexus (Standard) Toyota /Lexus (Advanced) √ √ √ For Middle
east cars,
it adds H chip all
keys lost(Immo
box reset) The Asian cars √ √ √ North American cars Ford(Standard) Ford (Advanced) √ √ √ Add Ford after
2015 key
programming
functions,I.E:
Mobdeo,Edge,
Taurus,Escort,
EVEREST,
Explorer,F-150
SVT Raptor,
Mustang,
Lincoln MKZ,
MKCand
Continental
2015 - etc. GM(Standard) GM(Advanced) √ √ √ The other American &
Chinese cars √ √ √ Can perform
BMC pin code
reaing on these
cars: -2017
Lacrosse,Lacrosse,
Trax,Envision, GL8,
MALIBU,
AVEO,Excelle before
2015,Cruze etc. Cluster Calibration All cars cluster calibration √ √ 4-system diagnosis Engine,
Transmission,
ABS, airbag reset OBDII Diagnosis Full functions diagnosis √ Full-system
all-cars
diagnosis Special function Oil service reset √ Reset the Oil Service
Light on Manual remote setting Some cars onl
supports manual
remote setting. ABS bleeding √ After replace the
ABS pump and
related components. Battery matching √ After the battery
is changed, you need
to match the battery. ECU programming √ The car with EPB replace brake pads √ Electronic
Parking Brake
release Throttle programming √ Used to clear
the learning
value after
cleaning the
throttle,
otherwise it
will cause high
idle speed. Airbag reset √ Used to clear
airbag ECU
collision data
after a vehicle
collision,
otherwise the
ECU cannot be
reused TPMS reset √ Used for reset
after tire pressure
alarm Steering angle reset √ Replacement of
data lost after
steering angle
change or power off OBDII Engine √ Used to diagnose
the car with
OBD protocol. DPF Regeneration √ Diesel Particulate
Filter Operational Injector coding √ Used to match and
code the injector
after replacement Suspension match √ Used to match and
set the suspension
after adjusting. Gear learning √ Used to learn
the crankshaft
position sensor
after power
off (only the
domestic vehicle
equipped with
the Delphi
system has this
function) CVT learning √ Used to reset the
learning value
after maintenance
of CVT transmission EEPROM √ Read and write the
eeprom;read 8-pin
IC chip password
and reset some
models anti-theft Key Renew √ Renew the used
keys to solve
the problem that
used keys
cannot be matched
to other models Steering angle repair √ Used for the repair
of lost data
of vehicle steering
angle sensor ECU Clone √ Used for copying the
program
when replacing the
new/second-hand
computer. Switch activation √ Hardware P001 Programmer unit √ √ √ C001 circuit board √ √ √ C002 circuit board √ √ √ W001 data cable √ √ √ W002 data cable √ √ √ W003 data cable √ √ √ Toyota smart key emulators √ √ √ Remote Tester √ √ √ Anti-theft Induction coil √ √ √ Used to test if the
coil can send
out the transmit
signal.
Part 3: obdstar X300 DP plus features & real pictures.
Hardware Advantages:
- Built-in VCI box
- 8-inch touch screen
- Chargedirectly via OBD interface
- Practical and high-end gift box
- Industrial design with silicone case
- Back bracket design:prop on the steering wheel or stand on the table
- With 4 Toyota simulation keys (the fifth is coming soon)
Simulated key 1 applies to the vehicle with 94/D4 type of smart key;
Simulated key 2 applies to the vehicle with 98 type of smart key;
Simulated key 3 applies to the vehicle with 88/A8 type of smart key;
Simulated key 4 applies to the vehicle with A9 type of smart key;
8. P001 programmer: EEPROM adapter + RFID adapter+ Key Renew adapter
- Add the clip of reading SOP 8PIN EEPROM
10. C001/C002 circuit board to read and write chip data with welding
Image 1: C001 circuit board is compatible with old NO. 3 and 4 circuit boards, applying to EEPROM chip dismantling and reading, Tianjin FAW and VIZHI immobilizer coil initialization and other functions.
Image 2: C002 circuit board is connected by W001, W002 or W003 without welding the chip.
- IMMO induction coil to detect the key induction coil failure of the vehicle.
12. Add wiring harness of ECU reading by OBD (for ECU cloning and switch activation)
ECU Programming/Cloning
ECU cloning means copy ECU, that is the OBDSTAR X300 DP Plus copies the data from the original car ECU, then write it into another same ECU hardware, so that it can achieve the same function as the original ECU.
When you want to change the new ECU or the second ECU, if you use X300 DP Plus to clone via OBD, you won't need to go to the 4s store to do the online programming or dismantle ECU to weld, read & write.
ECU clone Pros :
No need to go to 4S shop, convenient, fast and save money.
Simplify the operating steps, even the amateur can also operate.
No need to dismantle and weld the ECU to read & write, it is zero risk to clone ECU via OBD with the X300 DP Plus.
Switch activation function
Nowadays, many car models' accessory power supply of the dashboard or audio equipment needs to be activated to enter the boot status through the related module CAN.
However, when the car technician maintains the dashboard / audio equipment, the main unit is out of the CANBUS network so it maybe won't boot. X300 DP plus" switch activation function" can emulate the CANBUS communication to active the power supply of dashboard / Audio so that it can enter the boot status, then it will test and verify the dashboard and the Audio, also the technician can save money avoiding to purchase many the boot platform and cables of kinds of car models
13. Adds the "Help" functionincluding the testable car models, update notice, special features, help instruction, wiring diagram etc.
Testable car models: The user can read the testable car models and year.
Update notice: The user can read all of the update content.
Features: The user can read all of the special features and the functions that only X300 DP Plus supports.
Help instruction: Built-in the guide and instruction for each car model or function.
Wiring diagram: Built-in ECU wiring diagram, more intuitive and convenient.
Pictures mean a lot:
obdstar DP plus accessories:
OBDSTAR X300 DP Plus Package:
www.uobdii.com
UOBDII All rights reserved OBDSTAR X300 DP plus VS X300 DP VS Lonsdor k518ise
How to fix Carprog Clone LIB File Problem
Here is the working solution on Carprog clone "LIB file problem"
by re-flashing Mcu ARM AT91SAM7S256 step by step.
OBD Tech
Problem:
Any work solution for carprog v8.21 clone?
"Lib file problem. delete LIB file and make Update>-Internet"Solution:
Yes, reprogram ARM with any jtag programmer.Reflash Carprog MCU ARM by Jtag:
We need the stuff:
1- AT91SAM7S256.bin
2- Jtag programmer
3- Jtag software
We need to prepare the Carprog to connect to Jtag programmer but first the
flash need to be erased, the Jtag function in mcu is disabled, you can't connect
to the mcu before erase the flash. Remove the AT88SC eeprom from the board,
please note where is the pin 1 in eeprom before remove:Carefully lift the pin 55 (reset) of the mcu and solder a wire and secure it
with a small amount of silicone (you don't want to broke the pin in the
process).
Connect the Carprog (with the pin 55 disconnected) to the 12v
supply, wait about 10 seconds and connect the wire from pin 55 to Vcc (3.3V) in
Carprog:Wait from 5 to 10 seconds after connect the 12v supply, the flash content
will be erased and the Jtag option of the Mcu will be enabled now. If not work
leave connected for about 3 to 5 minutes. Disconnect the 12v supply from CarProg full and remove the pin 55 wire from vcc. The pin 55 must remain
disconnected until the programming process is done.
Ok, that's it. I make it; and you try on you risk.
Article from:https://carprog-carprog.blogspot.com/2016/10/how-to-fix-carprog-clone-lib-file.html
How to Use CGDI Coding for BMW F Series
This is a mini guide on how to use CGDI BMW Programmer to coding for BMW F-series.CGDI Connect OBD and click BMW F series codingChoose ECU info
Note: this function needs to connect the internet, please confirm the network is smooth, click ECU infoAfter reading ECU successfully, click on 3. FEM_BODYSelect Backup coding and choose yesNote: Coding succeed, this file is the save route Click coding Coding successfully
Src:https://www.cgdishop.com/wholesale/cgdi-prog-bmw-msv80-car-key-programmer.html
Newest OBDSTAR X300 DP Plus ECU Clone Function
Recently,OBDSTAR company have released their newest product called OBDSTAR X300 DP Plus(OBDSTAR X300 DP PAD2).It can clone ECU,so here i will introduce this function in detail.
OBDSTAR X300 Plus ECU Clone Function:ECU Clone
1. ECU Clone, means ECU duplication.
The
device copies all the data from the original vehicle ECU, and then
writes all data copied into ECU with the same hardware to realize the
same ECU function with the original vehicle.2. Clone directly when replacing a new or a used ECU!
Without
online matching in 4S store or removal of ECU bonding wire for reading
and writing! Directly write without dismantling OBD!3. Three features for ECU Clone:
A. Free of 4S online:
break monopoly from 4S, benefiting automobile maintenance industry
B. Simplified operation procedures: realize foolproof operation
C. Non-dismantling with zero risks: read and write data without dismantling ECU
src:https://www.uobdii.com/wholesale/obdstar-x300-dp-pad2-key-master-plus-full-configuration.html
Which Range Rover Key Programmer is Best for You?
It is necessary for auto locksmith to get a useful Range Rover key programmer.So here China OBD want to share some powerful device work on Range Rover keys programming.
Mart Tool Key Programmer
Mart Tool is designed to add new keys and program new keys when all keys
lost for Land Rover and Jaguar KVM keys with Number FK72 HPLA.
JLR SDD Multi Function Tool
New Arrival JLR SDD/ TOYOTA/ VOLVO Diagnostic/Programming/Matching Key
Multi Function Tool.Support JLR / TOYOTA / VOLVO . powerful , portable
,convenient and multi-language.For diagnostic , programming and matching
key , SDD+ can directly match the account of original VCM diagnostic
tool.
JLR SDD2 V149 Diagnose and Programming Tool
JLR SDD2 Support Landrover and Jaguar diagnostics, vehicle
reprogramming, immo and smart key functions, which work on both Land
Rover & Jaguar. JLR SDD Coded Access Password is able to used
together with any JLR Diagnostic tool with SDD software. It is used for
vehicle parameter programming. This offer comes with 100 times / tokens,
after used up, you need pay again for use.
How to Use CGDI Coding for BMW F Series
This is a mini guide on how to use CGDI BMW Programmer to coding for BMW F-series.
CGDI Connect OBD and click BMW F series coding
Choose ECU info
Note: this function needs to connect the internet, please confirm the network is smooth, click ECU infoAfter reading ECU successfully, click on 3. FEM_BODYSelect Backup coding and choose yes Note: Coding succeed, this file is the save route Click coding Coding successfully
https://www.cgdishop.com/wholesale/cgdi-prog-bmw-msv80-car-key-programmer.html
How to Use CGDI Coding for BMW F Series
This is a mini guide on how to use CGDI BMW Programmer to coding for BMW F-series.CGDI
Connect OBD and click BMW F series coding
Choose ECU info
Note: this function needs to connect the internet, please confirm the network is smooth, click ECU infoAfter reading ECU successfully, click on 3. FEM_BODYSelect Backup coding and choose yesNote: Coding succeed, this file is the save routeClick codingCoding successfully
Src:https://www.cgdishop.com/wholesale/cgdi-prog-bmw-msv80-car-key-programmer.html
CGDI MB Do All Keys Lost Programming for Benz W166
Mercedes Benz W166 all keys lost and program new keys, CGDI MB Pro is good choice, here share user manual with pictures.
CG Pro 9S12
Guide:
Select Lock(EIS)Click on "Read EIS data" then "Computer password"Click on "Copy key without key" then "Collect Data".CG100 ProgrammerPrepare to collect data, please wait...Please insert the simulation key into the lock in 30 seconds.CGDI MB programmer is collecting data.Data acquisition succeed, save it by default.Click on "Upload data" then open the data you saved.Upload data successfully.Click on "Query password"Wait for 2 minutes, query password succeed.Click on "Lock (EIS)" then CGDI MB display password, copy it.Click on "Paste password"https://handybaby.spruz.com/Article from:https://blog.cgdishop.com/how-to-use-cgdi-mb-do-all-keys-lost-programming-for-benz-w166/
New Mondeo Mileage Adjustment by OBDSTAR 300M Notice
There are three types of instruments for New Mondeo: big screen, small screen, dual screen. OBDSTAR X300M Odometer Corrector is currently supporting
calibration big screen and small screen, if you enter the wrong
type,the instrument will be black, after power on, then it can be
restored again.
Big Screen of New Mondeo-Supported by OBDSTAR X300M
Small Screen of New Mondeo-Supported by OBDSTAR X300M
Dual Screen of New Mondeo-Not Supported by OBDSTAR X300M,
Factory Still Developing!!!
From OBDSTAR Tools Technical Official Blog, post Notice to adjust mileage for New Mondeo BY OBDSTAR 300M
Xhorse VVDI Prog, Xprog and R280 Read BMW cas4 5M48H
Reading BMW cas4 5M48H, the optional working programmers are Xhorse VVDI Prog, Xprog 5.5, Xprog 5.6, Xprog 5.7, R280 plus and Smok, etc.Option 1: VVDI Pro read cas4 5M48H
Xhorse VVDI Pro can read and write 5M48H.
Here how to read 5M48H using Xhorse VVDI Prog.Procedure:
Video demo: https://www.youtube.com/watch?v=ZWrQdha-OO8&feature=youtu.be
Open VVDI Pro software, select type, manufacture and model as MC9S12XEP100)Click "Wiring Diagram"
Maximize wiring diagram: right click and select "zoom window", then pull down window.
Follow the wiring diagram to connect CAS to the VVDI Pro.Start to connect the cable.Car Key Programming Guide
The left zone is done, next is to do the right zone.In this wiring diagram, it only need to remove one 0 ohm resistor to
read out data, but one CAS ECU structure is different another one, some
needs remove more electronic parts; we will show how to do in the other
videos.Next is to remove this 0 ohm resistor.Wiring is done, 0 ohm resistor is removedPlug adapter into VVDI Pro.Close wiring diagram.Select "New" - " Read"
You see it is reading data very fast.
Reading data successfully, click "Save"Next is to check data.
Open the data, drag the mouse to check, okay, data is all read out, close it.Option 2: XPROG-M V5.55, XPROG-M V5.70 and XPROG-M V5.60
Compared with XPROG-M lower version, XPROG-M V5.55, XPROG-M V5.70 and
XPROG-M V5.60 add adaptor for 5M48H P-Flash, and already tested
successfully by many ECU tunners.Option 3: R280 Plus CAS4+ BDM programmer for MC9S12XEP100 chip (5M48H/1N35H)
Top 5 features:
- R280 Plus, a powerful Motorola microcontroller dedicated programmer, supports the latest BMW Motorola MC9S12XEP100 chip (5M48H/1N35H).
- It supports automatically search mileage address and display the mileage
- Remove the chip, directly input the number of kilometers, the data is visible and can be arbitrarily edited, it allows user to arbitrarily read and write /P-FLASH D-FLASH data.
- The latest generation of processor programmer.
- Using the latest software and hardware, hardware security level is high.
Powerful R280 Plus Update: Support for the upgrading of programming tools, to provide 24 hours of technical support, product 1 years warranty free upgrade.Powerful R280 Plus microcontroller dedicated BMW Motorola programmer supports following models:
BMW 1 series - F20, F21 chassis - 2016 years ago
BMW X1 series - E84 chassis - 2016 years ago
BMW 3 series - F30, F31 and F35 chassis - 2016 years ago
BMW X3 series - F25 chassis - 2016 years ago
BMW 5 series - F10, F11 and F18 chassis - 2016 years ago
BMW X5 series - F15 chassis - 2016 years ago
BMW 6 series - DMEM/F12 F13 chassis - 2016 years ago
BMW X6 series - F16 chassis - 2016 years ago
BMW 7 series - F01, F02, F03, F04 chassis - 2016 years ago
BMW GT series - F07 chassis - 2016 years ago
BMW CAS and CAS4 (0K50E/2K79X/0L01Y/0L15Y/1L15Y, etc.).
BMW EWS4 (2L86D).
EZS (1J35D/2J74Y/4J74Y/0L02M/1L02M/3K85K/3K91D/1L85D/1L59W/3L40K/4L40K, etc.).
Support for a variety of SRS computers
(9H91F/0K13J/0K75F/0L85D/0J38M/1E62H/1K79X/5H55W, etc.).
Support M35080 series quick wipe, read and write (35080/35080-V6/35080-VP/080D0WQ/160D0WQ/35160, etc.).
FLASH 0K50E online write.Have an overview on R280 Plus Software Display:
https://blog.uobdii.com/read-bmw-cas4-5m48h-by-xhorse-vvdi-prog-xprog-5-5-5-6-5-7-and-r280-plus/
OBDSTAR H108 to Calibrate Citroen Cluster via OBD
Used OBDSTAR H108 to do Citroen cluster calibration via OBD perfectly and easily, what I need to do is do what the screen display tells me to do.
OBDSTAR X300M Mileage Programmer
Plug OBDSTAR H108 to the Citroen BSI. OBDSTARSelect"Cluster Calibrate".CitroenSelect "BSI".Auto selectIf auto select failed, select "manual select".Select "JC BSIO4EV-KOX".Switch ignition onSelect "Read EEPROM".Please enter a filename to save, press the "ENT" button.Operation successPress the "ENT".Read Flash...Press the "ENT" button.Read Flash success.Press "ENT".Press "ENT".Press "ENT".Input a new value.Success.Done.
Perfectly, I am very happy with this OBDSTAR H108, it doesn't let me down. I highly recommend it.
https://www.keycuttingmachine.org
CGDI MB to Program Key for Benz
Attach some pictures on how to use CGDI Benz Prog on Benz step by step incl. lock (EIS), read/write key, generate EE, computer password, etc.
for more about CGDI,visit our official website:
CGDI Shop Here we go.
CGDI Prog on Benz: lock (EIS)CGDI Prog on Benz: read/write keyCGDI Prog on Benz: generate EECGDI Prog on Benz: computer password CGDI Benz key pro for sale:
https://www.cgdishop.com/wholesale/cgdi-prog-mb-benz-car-key-programmer.html
how to use OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32
Recently,OBDSTAR engineer share video guide on how to use OBDSTAR H100 program dealer key for VW Polo 2013 NEC 24C32.Here OBDSTAR share it for customers.
Procedures:
Connect OBDSTEAR H110 to vehicle by OBD port.
Power on the device.
Select "VEHICLE"Select "IMMOBILISER"Select"VW/AUDI/SKODA/SEAT"Select "VW/ADUI/SKODA/SEAT V33.25"Select "VW"Read security code4 Generation ImmoNEC+24C32 ICMMake Ordinary Dealer Key.Reading data ...
Please connect RFID with diagnostic devicePlease put the new key in RFID adapter.Reading data ...
Generating dealer key...When you find the LED light on the RFID adapter flash on 3 time,the OBDSTAR H110 Programmer will prompt you "Make Dealer key success"
Attention Please:
If you find the warning massage with "Communication Breakdown".Please check below conditions:
1.Ignition Switch is turned on
2.Mainline is connected
3.Battery has power
4.Is Equipped with this ....
OBDSTAR X300 DP PAD Programmer
From OBDSTAR Tools Technical Official Blog, post OBDSTAR H110 Program Key for VW Polo 2013 NEC 24C32
SEC-E9 Key Cutting Machine cut Chevy DWO4 car key+ Schlage home key
Choose correct space. In this case it is 8.Click "Menu" then "Info" at bottom bar to get key blank information.
Click "Decode", follow the screen guide, use stopper to put the original key correctly on clamp.Click "Decode" to start decoding.After that put the new Chevy DWO4R key blank on clamp, click "Cut" then set cutting speed.
Then replace the new blank key blade to cut.
Top 5 Auto Key Cutting Machine for Automotive Locksmith
Here are 5 auto automotive key cutting machine for auto locksmith.
1. Built-in Database, can easily find key information
2. Support Multi-languages:
Portuguese/Spanish/French/Germany/Czech/Arabic/Turkish/Dutch/Polish/Bulgarian/Norway/Slovakia/Italian/English/Chinese
(Turkish and Russian will be released in the future)
The way to change language:
Please provide us with the serial number and wait us to authorize the
language you want, then you can use the Update Tool to choose the
language.
3. Update Online Lifetime
4. 3-Axis Precision Ball Screw Transmission
5. Cross Rail
6. All Aluminum Machine Body
7. Single machine with both Tracer/Cutter
8. Standardly include clamps M1/M2, M3 needs to buy alone
9. Support Sided/Track/Dimple/Tibbe keys
10. Some Dimple/Tibbe keys need optional clampssrc:https://www.uobdii.com/wholesale/ikeycutter-condor-xc-mini.html
SEC-E9 CNC Automated Key Cutting Machine
1. Can directly search key bitting number by key code for some keys. No need to search from Instacode
2. Can cut a new key by bitting number, when original key is lost.
3. Support 10 languages including English, Spanish,French,German,Italian,Korean,Portuguese,Russian, Turkish, Czech.
4. Can cut veritcal milling, flat milling, internal milling and external milling.
5. Can cut automobile keys,motorcycle keys ,dimple keys, tubular keys, and single-sided standard keys.
6. Can cut Tibbe keys and LDV keys
7. Auxiliary Clamp is available
8. CE Approved
9. Work on Car, Truck, Motorcycle, House Key, Dimple & Tubular Keys
10. Update Online for Free
Automatic V8/X6 Key Cutting Machine with Dust Cover
1. It can be used with the key keyless condition, lightweight and
portable, battery-powered DC electrical impulse is very suitable to go
out to work.
2. Mainly used have the key with keyless lost data with the key. When
there is a key, simply follow the steps to enter the number or read key
teeth tooth number, you can make a new key. When a key is lost, just
follow the prompts, enter the appropriate number of head lock, you can
make a new key.
3. It is also can according your requirement ,through the intelligent
choice to make key tooth depth. Easy to use, suitable for a variety of
automotive lock key.
4. USB cable data transfer, compatible with a variety of key database
5. Quick change guide pin and cutter
6. Modular design, easy maintenance (Quick Change Module)
7. English menu. Configuration:
one PCS English manual ( Electronic files ).
one PCS 2.5mm dedicated mills. two PCS Dedicated probe 2. Spare belt.
one PCS USB data cable and one set Electrical impulse
8. Multi-language support: English ,Italian,Portuguese,Spanish
368A Key Cutting Duplicated Machine
1. Multi functional practical machine, equipped with horizontal feeding movable handle
2. Multifunctional steel fixture, can copy various hollowness type,wave
type,cylindrical key and key for multi lock and composite bead keys and
some car keys,such as BMW,HONDA,Volkswagen car keys
3. Fixture with dark key duplication service pitch line and cylinder type key assembly function (multifunctional clamp)
4. With hardened ball bearing slide mechanism.
JINGJI L2 Vertical Key Cutting Machine
1. Callibration system indicated by LED light make sprecisely cutting
2. Cutter speed regulated to 8500rpm
3. Straight line slide carriage makes cutting smooth and effortless
4. Cutting depth locking mechanism makes accurate result
5. Rmovable jaw with two grooves makes cutting more convenient
6. Vertical movement backwards makes more space to install clamp
7. Spring loaded tracer point make sperfect depth alignment
8. Structured with aluminum alloyed casting technique
9. Armrest support makes the cutting forward stable and smooth
CGDI Shop
More info about key cutting machine,please visit:Key cutting Machine
OBDSTAR X300M Adjust Mileage for Hyundai Mistra
OBDSTAR X300M is
ideal mileage adjustment tool for Hyundai Mistra 2017, because it
complete new kilometer adjustment via OBD without dismantling the
cluster.
Related Products
OBDSTAR X300 DP PAD Tablet
OBDSTAR X300 Pro3 Key Master
As you can see on the Hyundai Mistra 2017 dashboard, the old value is 20685KM.I will connect OBDSTAR X300M to the Hyundai via OBD2 cable, power on
it and go to the menu "Cluster calibration", you can see the car makes
option, choose "Hyundai".Hyundai V30.70.Loading...Initializing...Authorizing...As you can see, this is Hyundai supported list, choose " Mistra".Select "Kilometer".Communicating...X300M reads out the old mileage: 20685 kilometer, then you can see the dashboard info.Input the new value 10650KMCommunicating...Adjustment complete. You can see the dashboard display 10650KM.Done!
It's amazing to use OBDSTAR X300M to adjust mileage on Hyundai, it's
so easy even the user is not professional. I highly recommend it,
everyone can own one because it is cheap about 300USD.Like:
https://www.obdstartool.com/wholesale/obdstar-x300m-special-for-odometer-adjustment-and-obdii.html
$319 free shipping.
From OBDSTAR, post How to use OBDSTAR X300M to adjust Hyundai Mistra kilometer?
Review on OBDSTAR X300 PRO3 Key Master
At that time I was hesitated to purchase OBDATAR X300 PRO3 or SKP-900 key programmer
to program smart key for my Ford car. Now I'm glad for my choice to
X300 PRO3, of course I do not have bad reviews on SKP-900, it is also a
powerful and professional diagnostic tool, but I think X300 PRO3 more suitable for me.
OBDSTAR H108 X300 PRO3 key master by OBDSTAR Company features with the immobilizer
key programming function of SKP900, as well as new function such as
Odometer adjustment, EEPROM/PIC and OBDII. This car key programmer I
got from uobdii.com charged US$485, compared to skp-900 who would charge more expensive. And as far as I know uobdii 9th Anniversary Free Shipping is under the way, at the outset I took a little money for Shipping.
Well, why do I say that this key programming tool suitable for me? I use X300 pro3 to successfully correct odometer of my car for odometer value is high enough to put up with. Several days ago, my best friend borrowed to reset oil service,
he said it was easy to operate and he wanted to buy one too. I am
happy my OBDATAR X300 PRO3 helps to solve his trouble. I have owned
this hand-held key programmer for 3 months, and become a little expert
with it.
Here I also share with you how to update software for OBDSTAR X300 Pro3 Key Master
At first, you should download the update tool and diagnostic software on
www.obdstar.com, then double click the application to install.
Step1: When Update Tool installation complete, click the update tool icon on the desktop to start it.
Step2: Then click source menu, choose the program you want to update, click confirm
Step3: click and select all the software then click "update"
Step4: wait for several minutes until updating finished.
Final Statement: these are all my experience when using X300 Pro3,
there is no suspicion of selling, please purchase according to your own
needs and wishes.
OBDSTAR X300M
www.obdstartool.com
Xhorse VVDI2, VVDI Prog, VVDI MB tool Reviews
Xhorse electronics vvdi reviews here, incl xhorse the best:
VVDI mercedes review
VVDI Prog programmer review
VVDI2 programmer review
CGDIShop
- cost-effective and powerful
vvdi mb can renew elv without soldering the nec while the other
should sold out and not make via obd2, vvdi mb can renew EIS no need
token even its bga eis , while others cannot , with small budget can
program bga key with 6 minutes while with others you need 5 thousands
dollars to do , more over for w204 all key lost no body in the world can
do it while they are working on it with vvdi- 204 all keys lost ok
For 204 all keys lost one solution is to buy eis with key tested and ok- W203 password calculation via IR
I read pass W203 IR OK- W203 W220 read password ok
W203: EIS/EZS A203.545.05.08 - MCU ??? -read PSW IR - OK
W203: EIS/EZS A203.545.05.08 - MCU 1J35D - read PSW - OK
W220: EIS/EZS A215.545.02.08 - MCU ??? -read PSW IR - OK
- support older ESL
old ESL(motorola) are supported read through K-line yet......look in ESL menu, there are some possibility...for me are all older ESL from 202, 203, 208,209,201,211 and so...then
when in the adapter are socket for the 28-pin HC05E6 motorola, then are
this supported too...
the emulator is too for all this OLD type of ESL...- renew this namber 7G tronic 003 446 0310
Can renew this namber 7G tronic 003 446 0310
i have renewed 10 pcs of this part number, all success- made a key to W203
I have made a key for W203.
Works great but the remote controle opens only the drivers door.- Exchange W204 ESL without renew EIS
Exchange W204 ESL without renew EIS. In ESL Tools, write EIS with
password(Select Auto clear TP and personalized) tested and work ok- w204 w207 w212 all key lost work
All key lost:
W204 work
W207 work
W212 work
- read/write Fiat 9s12dg256b mcu without problem
Yesterday i read/write mcu 9s12dg256b from fiat bcm with vvdi Prog WITHOUT Problem- VVDI Prog secured very well
I work's on opel astra h cim with hc912 mcu,
ford dashboard hc912, and with hc908az60
secured very well.- 080dowq erasing works perfect
Now I tried 080dowq erasing, and it works perfect.- R/W ok with CIM Opel Astra H
3L40K - Read ID (0113) ok, Rean EEP (ok) Read Flash (ok)
1L59W- Read ID (0115) ok, Read EEP (NOT) Read Flash (NOT).Ps. 3L40K - Just that flash is smaller than It should be.
Read-it with smok, and You will understand what I am saying.- 50/50 chance to Porsche BCM
I have tried to read Porsche BCM with 9S12 5M48H dated 2013 MCU but
could not do it because VVDI Prog did not detected chip ID. Always get
ID: FFFF
While Porsche BCM with MCU 9S12 2M25J dated 2014 have read without problems- 209 flash ok
I received the vvdi prog and tested eis
209 with st12 eeprom flash ok- vvdi prog read ok with W221
for w221 ism with ST10F269 read by vvdi prog OK with micromax diagram
for write it didn't erase automatically you have to erase it before, then all OK .- ok with D70F3571
vvdi prog 4.5.1 D70F3571 read ok
- no issues with BSI 307 2002
BSI 307 2002 912DG128 - 3K91D
EEP (read and write) - OK
FLASh 4.000Mhz (read and write) -OK - Orange5 clone (DO NOT write flash)
Identical files Vvdi prog and Orange5, same EEP and FLASH.
Incircuit BSI photo of Orange5
.- vvdiprog + eeprom adapter without issues
works fine with eeprom adapter
does not work with test clip tried to different ones,
maybe i should try other one, if there is any higher quality,
or maybe because of cable length it doesnot work
- good at EZS, CAS2, CAS3, CAS3+ ...
this programmer can read write EZS, cas2, cas3, cas3+, read other motorolas safe without any problems or damages
- work OK on BMW CAS4 F10 2014
Today tested: CAS4 with Motorola 1N35H mask from F10 2014!
d/p-flash BACKUP - ok
Crack chip security - ok
read/write p/d-flash - ok
Locked - ok
Works without heating the chip. Only removed 4 elements from the board, and after operations resoldered them back.
i have desoldered 4 elements from the board: transistor, capacitator, resistor and cristal/quartz.- vvdi prog not working?:
- VVDI PROG CANNOT READ 68HC805 FOR IMMO MAZDA 323- It cannot read hcx05 at all.- Cannot support read pin code for psa and old chrysler
VVDI2 BMW:- CAS1 bmw read eeprom by obd
i did yesterday CAS1 bmw read eeprom by obd and got key info and cutting code- bmw ews direct by obd
vvdi2 bmw can make key in bmw ews direct by obd or need read ews dump by programmer then make key- program new keys to bmw e90 2008 USA
i have a vvdi2 with vag and bmw authroization
have to programmed new keys in bmw (bmw e90 2008 USA year), without keyless go
in original key inside transponder pcf7953 315mhz
My hint for you: Chinese keys work only transponder but remote need
to remove cas and do it on bench on tango or xhorse vvdi, but obd method
need always original for better chance chip is 7945 or 7953 which is 46
family good luck- support MED17/EDC17 dump tool
Xhorse vvdi2 v1.2.1 adds support for MED17/EDC17 dump tool, support
clone ECU(Menu->Special Function->MED17/EDC17 dump tool)
But sadly only work for Condor key cutting machine users
my vvdi 2 is full not basic.but function for edc17 only for condor cutter user.no for all vvdi2 full user
vvdi mb bga have the token system, if you have condor cutter 1 token in 1 day for free if you don't have you need pay
it is differentVVDI2 AUDI:- do Control head on A6
Vvdi2 able to do Control head on A6
need Transponder Sokymat Crypto 8E - Audi ID8E precoded by Component Security.
If you want to add remote key: 4F0837220AK, 4F0837220R, 4F0 837 220 - and others.- key learn for Audi A4 RB8 crypto (2004+)
VVDI2 key learn procedure for Audi A4 RB8 crypto (2004+) option:
Just read the pin and cs from ecu.
Make backup from cluster, and the cluster configuration.
Then make a dealer key, and learn it with pin.- Audi A7 2012 km done
Audi A7 2012 km done by reading config by obd then read eeprom by Programmer --- ok!- Audi S8 spare key job done
Did one Audi S8 done successfully, spare key job- add keys to AUdi a4 2009 BCM2
AUdi a4 2009 BCM2 key added successfully in 2 minuts.- Audi Q5 add keys, read bcm2
I did Audi Q5 add key ok, read BCM2 by OBD ok, read BCM2 by bdm ok.
Passat B6 all key lost by eep ok.- Audi A3 8P 434 not working
Remote programmer test remote for Audi A3 8P 434, not working.
Not file for Golf 5 434.
Test remote generator Ibiza 6J "1k0 .... N" 434 working.- Audi A4 2008 not working
VAG remote key adaptation does not connect to many old cars but
usually works fine with newer "dealer keys". However, Audi A4 2008 did
not connect to car (BCM or BFM). Key programming ok.
On a side note: A4 2008 do not have BCM, models 2009 + has BCM.VVDI 2 & others:- Peugeot 308 2008 BSI JC pin extracted
Peugeot 308 2008 BSI JC pin extracted OK. Key learn failed - first
key OK, second key failed. Tried several times. Job finished with other
device.- Passat B6 read code and add keys
Passat B6 read Code from confort module (95320) & added key ok!- 0D69J file identified
BENZ a class 0D69J file identified ok, but write transponder not work- Passat B7 failed
Passat B7 Read Code from confort (95320) & add key by obd --- Failed, (i made by transponder tool option)
VVDI Key Tool
UOBDII All rights reserved Xhorse vvdi review of VVDI2, VVDI Prog, VVDI MB
Auro OtoSys IM100 immobilizer system application
Auro OtoSys IM100
IMMO application requires a data link to the IMMO ele ctronic control
system of the test vehicle for diagnosis via OBD II connection. The
application retrieves vehicle IMMO information and performs IMMO related
functions,including Key Learning, Remote Control Learning, Remote
Control Add, etc.There are two options available when accessing the IMMO section:
1. Smart Mode - accesses to a function menu where each function is
configured as a smart guide system.
2. Expert Mode - accesses to a function menu where each function is
separated from each other.After a mode is selected and the tablet establishes communication with the
vehicle, the corresponding function menu or selection menu displays.
Smart Mode
The Smart Mode provides guided functions with step-by-step instructions.
Once the test vehicle is identified, a vehicle profile will display, select Yes to
continue.auto key program
The tablet will access the vehicle IMMO ECU to read IMMO related
information. Press OK to continue. Then the vehicle key status will display.Read the vehicle key status carefully and press OK to display the function
menu.The functions vary by IMMO parts, please follow the onscreen instructions to
select the correct IMMO part.
Automotive Key Programmer
src:https://www.uobdii.com/wholesale/auro-otosys-im100-key-programming-tool.html
How to use Kess V2 to disable DPF for Mercedes Sprinter 315 Biturbo
This article show the guide on how to use Kess v2 ECU programmer to disable DPF for Mercedes sprinter 315 biturbo
What is DPF?
A diesel particulate filter (or DPF) is a device designed to remove diesel
particulate matter or soot from the exhaust gas of a diesel engine.
What is DPF removal?
From February 2014 the inspection of the exhaust system carried out during
the MoT test will include a visual check for the presence of a DPF. A
missing DPF, where one was fitted when the vehicle was built, will result in an
MoT failure.
DPF off Mercedes with Kess v2, any success?
Yes, look here:
DPF off Mercedes Sprinter 315 biturbo with Kess v2 master
Any other solutions of Mercedes DPF
off?
Yes, download Professional DPF+EGR Remover 3.0:
(also done with Ktag
or Kess)
https://mega.nz/#F!zV1USZZL!X2mHnpX3Xc09sqYXlOAVgw
Mercedes ECU listed: EDC16C31, Delphi DCM3.4, EDC16C31 Vito and Type2,
EDC16CP36, EDC16C3, EDC16C31(2011+)EDC17CP10,M55 Error fixer
Professional DPF Remover 3.0 Car List:
Alfa : EDC16C39 Type1 and Type2
Audi : EDC16UX,EDC16CP3 / 34, EDC16U31, EDC17CP14, Siemens PPD v1.1, V1.2,
V1.3, EDC17CP44,EDC17C46,EDC17CP04, EDC16C34-4
BMW : EDC16C31 - 35, EDC16C31 (1MB), EDC17CP02,EDC16CP35, EDC16C31New,
EDC16C35,EDC17CP45 EDC17C41
Chrysler : EDC16CP31
Chevrolet : EDC16C39Citroen : EDC15C2, EDC16C34, EDC17C10, SID807
Fiat : EDC16C39(Ducato), EDC16C39 JTD, MJD 6F3, 6F3 Doblo, EDC16C39 Generic,
SID803A, Marelli 8F2, Marelli 8F3,
Ford : EDC16C34,EDC16C34-2, EDC16C34-2.29, EDC16C34-5, SID 206, SID807,
SID803MPC, SID803A, SID206(SMAX type), SID206 Kuga, EDC16C34 Picasso Type,
EDC16C3-9.18
Lancia : EDC16C39Honda : EDC16C31, EDC17CP06, EDC16C31(Advanced)
Hyundai / KIA : EDC16C39-D373, KIA EDC16C39 Type2,
Hyundai EDC16C39 Caren, EDC16C39 SantaFE, EDC17C08
Iveco : EDC16C39
Isuzu : Denso, Transtron DMax
Jaguar : SID204, EDC17CP11
Jeep : EDC16U1, EDC16CP31, EDC17C49
LandRover : EDC16C39-
Ford, SID208
Mazda : Denso 3-8 all series, EDC16C3,Denso CX7 Type with Adblue,
EDC16C34
Mercedes : EDC16C31, Delphi DCM3.4, EDC16C31 Vito and Type2, EDC16CP36,
EDC16C3, EDC16C31(2011+) EDC17CP10,M55 Error fixer
Mini Cooper : EDC16C35
Mitsubishi : Denso (Full 2 types supported), EDC16CP39
Nissan : Denso,EDC16C36, EDC16CP33 Type1 and Type2, SID305
Opel-Vauxhall : Denso,Denso Signum,EDC16C39, EDC16C9, EDC17C18 - C19, Marelli
MJET 75-90cv, Z16DT Marelli, Denso Signum, Z16DTC, Z19DT
Peugeout : EDC16C34, EDC15C2, SID803 MPC,Delphi DCM3.5, SID803A, Delphi
DCM3.4
Porsche : EDC17CP44
Range Rover : EDC17CP11
Renault : EDC16C3 Type1 and Type2,EDC16C32, SID305,EDC16C11
Saab : EDC16C39,EDC16C9
Skoda : EDC17CP14, PCR2.1, Octavia19
Bosch,EDC17U01,EDC17CP20,EDC16CP44,EDC17U01
Seat : Siemens PPD V1.2, PCR 2.1,, EDC17U01,EDC17CP20,EDC16CP44
Subaru : Denso
Suzuki : EDC16C3 Type1 and Type2, EDC16C39
Toyota : EDC17CP07
Volvo : EDC16C31 Type1 and Type2,SID803MPC,EDC16C34, SID803A Type1 and
Type2, EDC17CP22
VW : EDC16CP34, EDC16U31,,EDC17CP14, PCR2.1, EDC16CP34-4,
EDC17U01,EDC17CP20,EDC16CP44 EDC17CP46,EDC17CP52,EDC17P24, EDC17CP44,
EDC17CP54
All : EDC16 - EDC17 ECU's automatic DPF switch finder item * : Some EDC16
and all EDC17 ECU's solutions are using internal switches.
Which BMW key programmer is best for you?
BMW key lost or need a clone? which BMW key programmer to use?
When you plan to buy a BMW key programmer online, have you wonder which
key programmer do I know? Have you ask yourself or your friends like
this "among these BMW key programmer supplied by the seller, which one should I buy"?
In the following parts, I will list some BMW key programmers, and generally tell you their similarities and differences.
CGDI BMW
1.High technical tool which mainly support Auto diagnose, programming and security maintenance 3 in 1.
2.Support Key Programming for BMW CAS1/CAS2/CAS3, and Support Key Matching and All key lost for CAS4 /CAS 4+;
3. Support BMW Key Programming with OBD Functions
4. Software response fast, short time programming, and new breakthrough in operation safety and technical support.
5. Supported Languages: English, Chinese
6. Certification: CCC,CE,GS, CCC,CE,GS,ISO
7. Warranty:1 year
8. Free Update Online on official website https://www.cgprogcar.com/?langid=en, when you receive the device, please download software on official website too.
9. Newly Add BMW FEM/EDC Function for free
https://www.cgdishop.com
AK90 Key Programmer AK90+ For All BMW EWS
Newest AK90 BMW KEY-PROG V3.19 is a safe and effecitive key match tool
for BMW EWS system. It covers EWS2.1/EWS2.2/EWS3/EWS3.3/EWS4/EWS4.4,can
read all EWS key information from 1995-2005.
Newest version:V3.19AK90 Functions:
1. Directly reading data dumps from MCU which marked 1D47J , 2D47J ,
0D46J ,2L86D without removing MCU from circuit board , easy to do
yourself.
2. With the help of software you can renew , lock or unlock keys as well.
3. Programming original chips "EML 10030A" for making keys .
4. Identifying keys for all EWS and CAS , showing VIN , key No. It can change VIN, can change mileage in ews.
BMW CAS AK300 AK300+ V1.5 Key Maker
AK300+ BMW CAS Key Maker (Support in 2002 -2009 years) especially for
BMW CAS system key programmer.Support new BMW CAS,CAS2,CAS3,CAS3+.
Automatic analysis CAS data,easy to match keys.
AK300 highlights in features and functions:
Highlights:
Language: English, Chinese
Operation System: Windows XP
Car Coverage: BMW 2002 -2009 Year
Firmware Version: 1.16
Software Version: 1.50
Support new BMW CAS,CAS2,CAS3,CAS3+. Automatic analysis CAS data
AK300+ Features:
1 BMW CAS supports a diagnosis of communication directly through the OBD port or through the CAN BUS port security to read and write data EEPROM;
2 automatic analysis CAS data, automatically displays the BMW keys to
use quantity; key tooth number; remote control frequency; CAS with the
DME synchronization ID; keys scrapped the state, etc.;
3 supports key scrapped or restart using the old key; this technology unmatched global technology;
4 supporting the rehabilitation of CAS computer (due to transfer table is damaged or programming lock);
5 supports the new 2002-2009 BMW CAS; CAS2; CAS3; CAS3+
6 support the horse CAS; CAS 2; CAS 3; CAS 3 + BMW and BMW remote key.
7.support E65/E66/E87/E60/E61/E90/E91/E92/E93/E71/E71 HiTag2 V3.1 Programmer
HiTag2 v.3.1 programmer is universal key programmer, with additional
options of key programming from dump and PIN extraction. Just insert
blank key or appropriate transponder you need to program. Device detects
transponder type and will do everything automatically.
Language: English
Functions:
1.BMW (CAS1/2/3/3 +) at 912/9S12 immo + remote control, editing, KM,
VIN, reading data from the key, read / write eeprom of the transponder,
reading data from remote
2.AUDI (Kessy) on 93C66 immo + remote, read PIN, edit VIN number and immo
3.VW (Kessy) on 93C86 immo + remote, read PIN, edit VIN number and immo
4.PORSCHE (Kessy) on 93C86 immo + remote, read PIN, edit VIN number and immo
5.BENTLEY (Kessy) on 93C86 immo + remote, read PIN, edit VIN number and immo
6.CHRYSLER (State) on the 95040/95080 immo + remote, read PIN, VIN Edition
7.LAND ROVER (EWSх) to immo 9S12, editing VIN
8.NISSAN (NATS) at 95,080 immo
9.OPEL (CIM) in the 9S12 immo + remote, read PIN, VIN Edition
10.RENAULT (UCH) on 93C66 immo + remote, read PIN, VIN Edition
11.SAAB (CIM) for the 93LC66 immo + pilot edition of the VIN
Features:
1. Latest versions of HiTag2 transponders are fully supported.
2. Widest range of supported cars, using HiTag2 protocol.
3. Deep research work, has allowed us to make device, as much as
possible correctly adding keys in the car, without damage to its
functionality!
4. Correct BMW keys programming - RADIO REMOTE is working.
If you want to know more about BMW key programmer,you can visit our online shop uobdii.com auto key programmer
UOBDII All rights reserved Which BMW key programmer do I know
How to Update CGDI BMW Software?
CGDI Prog BMW MSV80 key programmer is able to update firmware and software on the official site: www.cgprogcar.com. Below parts incl. CGDI Prog Firmware and software update instruction.This post show the guide on how to update CGDI BMW software.
Step 1. Receive message " There is a new version", click on "OK"Step 2. Click on "Setting", then "Check for updates", waiting until the next dialog box appears.Step 3. Checking local file.Step 4. Detects a new file, click "Yes" to update.Auto Key Cutter
Step 5. Downloading file.Step 6. Finish loading software.Step 7. CGDI programmer software update successfully. Ready to use the newest software.Done.
CGDI Prog
OBDSTAR X300 DP VS XTOOL X100 PAD2 comparison table
In order to make you clear the difference between new arrival OBDSTAR X300 DP and XTOOL X100 PAD2, here uobdii.com give you a comparison table as below:
OBDSTAR X300 DP
XTOOL X100 PAD2
OBDSTAR X300 DP
XTOOL X-100 PAD 2
Operating System
Android 5.1
Android 4.4
CPU
Samsung Exynos4418 A9 industrial-grade processor
Rockchip civil-grade processor
Storage space
FLASH 16G
FLASH 16G
RAM
2G
1G
Battery
7400mAh
4000mAh
Resolution
1280*800
1024*768
Screen size
7 inch
8 inch
HDMI
Available
Available
Communication
Wire/Bluetooth
Only wire available
WIFI
Available
Available
Dimension
215*147*30
240*177*24
Shell
Three proofing and industrial-grade shell with rubber coating
Civil-grade
One key upgrade
Available
Available
One key enter
Available
None
Database
Built-in database
Optional, pay extra
Technical support
Expert service team
Pincode inquiry
7*24 hours automatic inquiry is available for most pin code
Manual inquiry
Fault diagnosis
All systems diagnosis are included
Only basic disgnosis for four systems
Conclusion:
OBDSTAR X300 DP is
superior to XTOOL X100 PAD 2 in many aspects, such as faster CPU, bigger
RAM, long lasting battery and higher resolution.
OBDSTAR X300 DP has Bluetooth and One Key Enter functions while XTOOL X100 PAD 2 cannot support.
OBDSTAR X300M
https://www.obdstartool.com/wholesale/obdstar-x300m-special-for-odometer-adjustment-and-obdii.html
For OBDSTAR X300 DP it's no need to inquiry pin code, but XTOOL X100 PAD 2 need inquiry manually.
And most important is
that XTOOL X100 PAD 2 can only allow you to diagnose the basic four
systems, but with OBDSTAR X300 DP you can diagnose all systems!
OBDSTAR X300 DP full package
Immobilizer+ odometer
adjustment+ EEPROM/PIC adapter+ OBDII+ ABS+ TPS+ SRS reset+ TPMS(low
tire)reset+ Steering angle reset+ CVT learning/Value reset+ EPB+
Oil/service reset+ Battery matching+ Diagnosis for Japanese and Korean
serials (extra bonus function)
Article form OBDSTAR Blog : OBDSTAR X300 DP VS XTOOL X100 PAD2 comparison table
Launch Easydiag 3.0 Update Version of Launch Easydiag 2.0
Recently,Launch X431 co.Ltd released their new product Launch Easydiag 3.0 plus,the update version of Launch Easydiag 2.0.Launch Easydiag 3.0 Description:
Launch EasyDiag3.0 is an integrated service platform based on automotive
diagnostic solutions. Key features include automotive diagnostics,
operational data query, vehicle maintenance, data and information
sharing. The client communicates with the vehicle using a Bluetooth
connector (DBScar connector).
Here UOBD2 make a compare between Launch Easydiag 3.0 and 2.0
LAUNCH Easydiag 3.0 Plus
LAUNCH Easydiag 2.0 Plus
Image
Price
$165 with 2
free car software
$180 with
2 free car software
Bluetooth
√
√
Android
√
√
IOS
√
√
Function
Read and
clear codes
√
view enhanced
live data
√
Systems
Engine
√
√
ABS
√
√
SRS
√
√
Transmission
√
√
more
√
√
Coverage
Asian makes
√
√
European makes
√
√
North American
makes
√
√
Customizable software
2 free vechicles
software+DEMO+EOBD
2 free vechicles
software+DEMO+EOBD
Update
Online for 1-year free
Online for 1-year free
Language
Multi-language available
Multi-language available
CARPROG Full ECU Chip Tunning Feedback
This post collects all of available customer feedback on CARPROG Full ECU Chip Tunning. Hope it helps!
- CARPROG works with both solution, odb and welding to read the EPROM.
CARPROG full v7.28 with everything and explained in the software, and it comes with several
connectivity number. As selecting a function that we want to use it tells us what connectors used.
It is even illustrated with photos very nice.Car Key programemr
2.
For me, it's not bad to begin with, the basic equipment (hot air station, flux pen, soldering iron with a fine tip) ismandatory to exploit
3.
Beginners opt for CARPROG.It offers a lot of opportunity, it does not cover all but a good party. Simple handling,intuitive app. it is polivalent dash, immo, radio ..
4.
I used to virginiser of BSI, I also managed to modify a 2002 vehicle en dash (just to test, Idelivered as it was before)
I also managed to lire OF 5p08 (95p08) and write off properties not bad for beginners, less effective than XPROG or UPA but easier to use.
good flash
5.
Question: You have a merchant recommend? a Chinese version is it the case?
Reply:https://www.uobdii.com/wholesale/carprog-full.html
They are well and have a very proper customer relationshipQuestion: You mean the clone or the original? Because the budget is not the same ... And the clone functionality level, we can estimate how many percent compared to the original (if quantifiable)? Gadget or good tool to start?Reply: It is 40% of the original on the radio codes ok but the dashboard there is not any lack of image the rest is a very fragile CARPROG use it after several silliness more communication with the interface, it must be used with a PC without internet with a stable and xp ca va ...
Super good tools began frankly I'm very happy easy to use but it's still the lolll brol as a tool that makes
https://blog.uobdii.comseveral operations:
-airbag
-code radio
-Immo
-counter
-ecu opel
-some ePROM
-some mcu
(A tool that helps you one day is priceless ...)This article from:https://carprog-carprog.blogspot.com
OBDSTAR X300 DP PAD OBDII Diagnosis Function
This is an OBDSTAR X300 DP PAD Programmer user manual, from vci connection to auto obdii diagnosis. The most details for you all, especially for newbies.
obdstar x300 pro3 key master
VCI connector connection
- Locate vehicle's DLC socket. The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized 16‐cavity connector where diagnostic code readers interface with the vehicle's on‐board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver's side for most vehicles. If Data Link Connector is not located under dashboard, a label should be there telling location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. If the DLC cannot be found, refer to the vehicle's service manual for the location.
- Plug the VCI diagnostic connector into the vehicle's DLC socket (It is suggested to use the OBD 2 extension cable to connect VCI connector and DLC socket.). For non‐16PIN DLC socket, please select the corresponding non‐16 pin connector adapter, then plug the non‐16pin end
1.Enter Key Master to set System setting, and choose VCI information.
2.Operate according to following prompt:
A."Please match: VCI_888888888888(Bluetooth name)"
b."Connected: VCI_888888888888(Bluetooth name)"
C."Not connected: VCI_888888888888(Bluetooth Name)" Please connect VIC connector to vehicle, X300 DP will connect automatically.WIFI setup
- Set Wi‐Fi on
- Enter main menu screen, choose "Settings" > WLAN
- When the WLAN sign appears blue, , it indicates Wi‐Fi has been activated already.
unattended.
Connect to WLAN
Start WLAN, if X300 DP within range of WLAN, X300 DP can automatically detect and connect to current WLAN, select desired network and input password, then you can surf the internet by WLAN.Diagnosis flowchat
For new users, please follow the operation below to get familiar with and start using X300 DP.
VCI diagnostic connector VCI -> Bluetooth connection (USB connection)->user registration->user login->download or upgrade software->select function or vehicle type->proceed diagnosisUser registration
Click on the "DP" button to enter user registration diagnostic software. Select "the user information" in the "setting" menu, then enter user registrationFill in the information in each field (Items with * must be filled). After inputting, tap "OK"
If you have registered to be a member, click on "the user information" to enter user login pageX300 DP diagnosis software download
Tap "One Key Upgrade" to enter one key upgrade page, as following picture shown:Tap "One Key Upgrade" to start downloading, enter main interface after finishing downloading. (Notes: Ensure internet connection is normal when updating. Besides, because of many software, it may take several minutes, please wait patiently) If need to cancel a software, just tap corresponding Check Box as below:Start Diagnosing
Tap on the main menu screen, and then choose "DP" to enter the function selection and vehicle selection page.Hereinafter, take OBDII for example, to introduce how to start diagnosing.
Tap " OBDII ", and tap "OBDII" icon.To select software versionTo enter diagnostic function menu,To select AUTO SCANRead vehicle informationRead trouble codeClear trouble codeRead data streamNote: there are two versions of x300 dp obdstar in the market:
OBDSTAR X300 DP Standard version= Immobilizer+ Odometer Adjustment+ EEPROM/PIC Adapter + OBDII diagnosis
OBDSTAR X300 DP full version= Immobilizer + odometer adjustment + EEPROM/PIC adapter + OBDII diagnosis + ABS + TPS + SRS reset + TPMS(low tire)reset + Steering angle reset+ CVT learning/Value reset + EPB + Oil/service reset + Battery matching
( it works well in Diagnosis for Japanese and Korean cars.)
https://www.obdstartool.com
From OBDSTAR Tools Technical Official Blog, post OBDSTAR X300 DP PAD OBDII Diagnosis Function Guide
SEC-E9 to cut Toyota TOY43 keys in 2 ways?
Post on how to cut Toyota TOY43 keys with SEC-E9 automatic key cutting machine in 3 steps: Enter the key data, get the key number and cut the key.Guide:
- Enter the key data of Toyota TOY43 in two ways.
Way 1: Select car manufacture, brand and year.
Tap "Automobile" button and "Toyota - Camry - 2006 -[10] to enter the key data.Way 2: Input the key blank number
Tap "Search" button, input "TOY43" and select "Silca" - "TOY43(903) [10] " to enter key data.Tap "Info" button to see the key is aligned by tip. Usually no need to use stopper when fix the key position.
Step 2. Get the key numbers of Toyota TOY43 keys using SEC-E9 in 3 ways.
Way 1:Decoding the original key.
Tap "Decode " button to enter the decoding page.
Select the dark blue icon as sense key location and "Round off".Check if the original key can open the cylinder.Fix the original key on the top level of the clamp. please pay attention to the key position.Tap the "Decode" button to start decoding the original key and get the key numbers.Way 2: search key code.
This is key code for Toyota Camry key.Tap "Code" button and input "55062" to get the key number.Way 3: Input key numbers directly.
Tap "Input" button and input the key numbers you get from other ways, such as cylinder, Lishi tool, or instacode, etc.
Step 3. Cut a new Toyota Camry key.
Tap the "Cut" button to enter the cutting page.Select "NKI-silver" as speed and the most right blue icon as sense key location.Take out the original key and fix a new key blank on the top level of the clamp. Please pay attention to the key position.Tap "cut" button to start cutting a new key. Please remember to close the safe gate.
SEC-E9 Cutting is done. Open the safe gate. Clean the clamp & the new keys.
Take out the new key.The new key is working well.
https://www.uobdii.com/wholesale/sec-e9-cnc-automated-key-cutting-machine.html
https://www.keycuttingmachine.org
SBB Key Programmer Register Nissan Note 2007 Chip Key
This is a Nissan Note 2007 (automatic, right wheel, Intelligent Key).
There
is a working key, customer need to add chip key startup..So this post
show the guide on how to register chip key for Nissan Note 2007 by SBB Key Programmer.(Note: The tutorial is translated from Russian, for educational purpose
only)
Diagnostic device
ABRITES Vehicle Diagnostic Interface ,
when selecting (Nissan Note 2006+) requires a 12-digit PIN code, which is
presumably considered for label located behind the glove compartment (glove
box).
But the car has a sticker, so the chip should be registered with
the device SBB Key Programmer.
How to calculate PIN code for registration key / chip in the car?
PIN will be assumed by the label BCM, with the help of the program AD600 Code Wizard Pro (Demo the Version) , which can be downloaded at this link. Or by hand-held Nissan Pin code reader NSPC001.To perform this procedure, you'll need:
- Net HITAG 2 transponder - PCF7936.
- Wires (jumpers), for supplying power to the ignition contacts.
How to register the vehicle key / chip on Nissan Note using SBB Key Programmer?
1. Insert the device connector SBB v46.02 in OBDII vehicle.2. The instrument select NISSAN JAPAN - the MICRA MARCH 00- - Gasoline
3. Then Insert a key and turn on the console - Insert the key into the lock, and turn the ignition switch on.
4. The instrument choose NATS5 - the PROG. NEW KEYS.5. Without the PIN CODE you CAN not program new keys - Without a PIN, you can not program the new keys.
6. Enter the 4-digit PIN number, counted on the label BCM.
7. Insert keys to be programmed in sequence and turn them on and off for 5 sec respectively. In the end start the engine for some sec. Press any key ... Press - Insert the key to be programmed in sequence, one after the other, on and off the ignition for 5 seconds. After the end of the programming start the engine.8. Once the button is pressed all quickly, without errors:
- LED standard signaling, in the right corner at the windshield starts to blink.
- Turning off the ignition, take out a sting from the ignition.
- We put a thorn in the ignition, turn the ignition.
- Turning off the ignition, take out a sting from the ignition.
- Place the transponder antenna on the ignition.
- Provide the + 12V on wire and KEY IN KEY PUSH (red-blue and red and white, respectively).
- Turning on the ignition by supply of + 12V to the corresponding contacts ignition.
- Turn off the ignition.
- We start the engine.
Article from SBB Key Programmer Blog Site: https://sbb-keyprogrammer.blogspot.com/2017/12/sbb-key-programmer-register-nissan-note.html
OBDSTAR X300DP Adjust Mileage for Cadillac ATSL 2016
OBDSTAR X300 DP PAD
tablet Key Programmer not only play with programming keys but also some
special functions like program ECU , read Pin code, adjust Mileage etc.
Really a higher level diagnostic tool for workshop or dealer.Here is step by step procedure of changing mileage for Cadillac ATSL 2016.Device:
OBDSTAR X300DP PAD Tablet Key ProgrammerVehicle:
-Cadillac ATSL 2016Step1: Prepare
Connect X300DP with vechile and open X300DP
Press on START buttonStep2: Choose vehicle information
Choose "Mileage adjust" option and click on GMChoose GM V30.45 to go onThen choose CadillacChoose ATS2013-Mileage adjustment (correction)It is communicating...Step3: Adjust mileageThe current mileage informationInput the new mileage and press ENTER to continueValue: 3061It is communicating...
The mileage value at presantDone! Successfully change mileage for Cadillac ATSL 2016More info about OBDSTAR X300 DP,pls visit:
https://www.obdstartool.com/wholesale/obdstar-dp-x300-pad-system.html
CARPROG Full ECU Chip Tunning Feedback
This post collects all of available customer feedback on CARPROG Full ECU Chip Tunning. Hope it helps!
- CARPROG works with both solution, odb and welding to read the EPROM.
CARPROG full v7.28 with everything and explained in the software, and it comes with several
connectivity number. As selecting a function that we want to use it tells us what connectors used.
It is even illustrated with photos very nice.Car Key programemr
2.
For me, it's not bad to begin with, the basic equipment (hot air station, flux pen, soldering iron with a fine tip) ismandatory to exploit
3.
Beginners opt for CARPROG.It offers a lot of opportunity, it does not cover all but a good party. Simple handling,intuitive app. it is polivalent dash, immo, radio ..
4.
I used to virginiser of BSI, I also managed to modify a 2002 vehicle en dash (just to test, Idelivered as it was before)
I also managed to lire OF 5p08 (95p08) and write off properties not bad for beginners, less effective than XPROG or UPA but easier to use.
good flash
5.
Question: You have a merchant recommend? a Chinese version is it the case?
Reply:https://www.uobdii.com/wholesale/carprog-full.html
They are well and have a very proper customer relationshipQuestion: You mean the clone or the original? Because the budget is not the same ... And the clone functionality level, we can estimate how many percent compared to the original (if quantifiable)? Gadget or good tool to start?Reply: It is 40% of the original on the radio codes ok but the dashboard there is not any lack of image the rest is a very fragile CARPROG use it after several silliness more communication with the interface, it must be used with a PC without internet with a stable and xp ca va ...
Super good tools began frankly I'm very happy easy to use but it's still the lolll brol as a tool that makes
https://blog.uobdii.com
several operations:
-airbag
-code radio
-Immo
-counter
-ecu opel
-some ePROM
-some mcu
(A tool that helps you one day is priceless ...)This article from:https://carprog-carprog.blogspot.com
Lonsdor K518ISE & VW 4th immo 35xx all keys lost
Tutorial: How to use Lonsdor K518ISE Engineering Mode for VW 4th immo 35xx all keys lost
Lonsdor K518ISE Engineering Mode:
Read data, make a dealer keym, learn key, unlock key
Way 1:
Step 1: Select 4th immo
Step 2: Select Engineering Mode
Step 3: Go to Lonsdor K518ISE Engineering Mode to read data
Step 4: Read data via OBD:
1 all data (incl. all keys lost) will be saved under CUSTOMEFILE of K518 main unit
2 the data will be sent to professionals to calculate immo data
3 the immo data can be used for dealer-key making
Step 5: Enter a file name and save data
Step 6: Send the data for calculation
Step 7: Data location
Step 8: Make a dealer key
Step 9: this function allows loading data to make a dealer key or OEM key (copy original ID), then lean key
1 put immo data (BIN file) under CUSTOMEFILE
2 make a key with the immo data
3 learn key and re-match all keys
Step 10: Select calculated data
Step 11: Immo data type, cs code, pin code
Step 12: Make an OEM key
Step 13: Select VW
Step 14: Select key 1
Step 15: Put the blank key into K518 slot
Step 16: Made a dealer key successfully
The generated chip doesn't need learn key on the car; it's ok to use it directly.
Electronic ID48 chip cannot be generated into an OEM key
Change it into ID48 chip
Remote generation completes
Way 2: (NOT recommend)
You aren't
advised to go for Way 2, because it may kill your car when you go to 4S
chop to change immobilizer component(s) or delete some settings online.
But it's good those have lost a key and wanna delete key info
Learn key then match the key, then change all key locks or teeth to satisfy customers
Step 1 - Step 11: the same
Step 12: select: Make a dealer keyProgram 4th immo keys successfully.
Tested and it's working.
Job's done.
Happy with Lonsdor K518ISE
Article from Lonsdor K518 blog site:https://lonsdor-k518.blogspot.com/2017/12/lonsdor-k518ise-vw-4th-immo-35xx-all.html
What Devices Support VW MQB System Programming
Here are 3 programmers that can support VW MQB system programming:OBDSTAR X300 DP PAD,OBDSTAR X300M and Xhorse VVDI2.
OBDSTAR X300 DP PAD
X300 DP PAD not only support VW MQB programming,but also work on BMW FEM/BDC system programming.OBDSTAR X300 DP is the first tablet of OBDSTAR, which has reached a
higher level in key programming and diagnosis. Inheriting from OBDSTAR
professional auto programming and advanced diagnosing technology, X300
DP is characterized by covering wide range of vehicles, featuring
powerful function, and providing superior quality.
OBDSTAR X300M
OBDSTAR X300M is the most professional device for odemeter
adjustment,which coverage conprehensive car model.Main unit system of
OBDSTAR X300M adopts ARM high speed chip to keet it running stable,fast
and anti-jamming.This product can support VW MQB system odometer correction.
Xhorse VVDI2
VVDI2 Full Version comes with Basic Function + VW + BMW + Porsche+PSA+
AUDI Generation 5 Function+BMW OBD Fucntion+BMW CAS4+ Functions +Tango +
J2534, No Need to buy other Authorization.VVDI2 Covers All the
Functions of VVDI, VVDI 5th IMMO Adapter, BMW Multi Tool,CAS4 Adapter,
Tango & J2534.
Top 3 Mercedes Benz Key Programmer
Here I share Top Mercedes Benz Key Programmer to improve work efficiency.All of them can save you much time.Time is money!
https://www.launchx431v.org
Xhorse V3.6.0 VVDI MB BGA TooL
Xhorse VVDI MB BGA TOOL Function Introduction:1. Support BE key, read password and prepare new key via IR.
2. NEC V051,V057 support on board get password
3. All NEC keys support on board write and erase
4. Password calculate:support BGA keys,NEC keys(include 51,57version)etc.,work fast.
5. Support renew EIS and ELV
6. Support write EIS and ELV
7. Support online generate key file
8. Unlock ELV function will be released soon.
9. Renew other control modules function will support soon
CGDI MB Prog Mercedes Benz Key Programmer
1.Support fastest Benz Car key add: collection time 1'50s, password
calculation time 40s, 99% get password for one time calculator, it is
the fastest key programming tool to calculate the password at present.
2.Support MB all key lost: support models including 211,209,204,207,212,166,246,197,172,164 +, 216
3.CGDI Prog MB can calculate the password twice free each day.
4. Free Update Online on official website
https://www.cgprogcar.com/?langid=en, when you receive the device, please
download software on official website too.
1. Match and support function "Keyless Go" of Benz Infrared Key;
2. Support Benz Infrared keys lock and unlock for EIS+ESL+ESM , the leading technology all over the world;
3. Support Directly reading EEPROM for BENZ DAS( 1995-1998 )via OBD,
able to unlock DAS when you lost all keys and DAS is locked;
4. Read and write the ESL of E/Class and C/Class via K_line, no need remove ESL;
5. Support Benz ECU's flash(29F400 and 29F800) generating key data. Need to use STAR 2000 to do ECU coding.
6. No need to choose the MCU type of EIS. When load EIS file, recognise
EIS file, and generate key file. If your MCU is HC705, software will
automatically suggest "load next EIS file of HC705"
Article from:https://www.keycuttingmachine.org
How to solve MB SD C4 Insert Batteryi and Initialization Failed
Mercedes Benz MB SD Connect Compact 4 MB Star diagnostic system "Please
insert batteries" and"Initialization of diagnosis multiplexer failed" solution
are provided.MB SD C5
Problem:
One of the Mercedes MB SD
Connect C4 user has the problem when using the star C4 diagnostic
system.
Error 1: Please insert batteries.Error 2: Initialization of diagnosis multiplexer
failed
Possible reason:
He has not got the MB SD C4 connected with Dell D630 laptop to build
communication.
Mercedes Benz EIS Trouble Repair Guide
Solution:
Check the SD Connect C4 icon on the bottom of the toolbar, power on the
SDConnect and connect the diagnostic scanner with computer, if the #21 device
displays in "x" status,it indicates the C4 multiplexer is not well connected or
well configured,how to tell:
1.Open laptop Local Network Connection->SD C4 WLAN,disconnect then connect
to check if network connection has changed. If the network remains
unchanged,change another laptop and do the same setting.
2.If network status did not change on any laptops,then change a new LAN cable.If still no changes,you have to
send back your SD C4 main unit for repair.
Autel MS908P repair BMW 328xi E90 window regulator
The story is that: a 2006 BMW 328xi E90 rear right window was not
working, replaced window regulator but it was stuck not all the way up
and down. Used Autel MS908P to repair window regulator OK! So share this success case here.
How Autel MS908P initialize BMW window regulator, reset BMW auto window?
Plug the J2534 ECU Programming Device into car OBD port. Then you can use it to connect Autel MaxiSys Pro MS908P with car via Wi-Fi.
Click "Diagnostics" and choose "BMW.Autel DS808K
Or you can directly click the VIN button at left upper corner, choose
"Auto detect" and it will read VIN automatically and show vehicle
information.Now you need to connect car with power charger over 12V. Then put remote key into key slot and press car Start button.
Then go to "Hot Function".Choose "Window, door and roof" then "Initialize window regulators" function.Follow the tips "Switch on terminal 15 (ignition)", keep remote key
in key slot and do not press the brake pedal, press car Start button to
turn ignition to terminal 15.
Choose to initialize the "Passenger's side, rear" window regulator.BMW Trouble Repair
The rear right window will automatically open and close.
After that you can roll up and down that window normally.
Autel MS908 Pro successfully initialize BMW 328xi E90 rear right window regulator! BMW auto window reset OK!
UOBDII All rights reserved How to repair BMW 328xi E90 window regulator by Autel MS908P?
Volvo Tech Tool PTT 2.05.20 Free Download
Here you can free download Volvo PTT 2.05.20 in mega! Link is tested working. Check below:
Free download Volvo Premium Tech Tool 2.05.20:
https://mega.nz/#!WZ4GRRYR!EBvasNyBwXJEo6CkMSWCmHTkxVV92FNk70vlxBllzzE
Totally 1.97GB may cost a while depending on your network condition.
Volvo PTT All version download here:
Volvo PTT Premium Tech Tool Free Download
Note: Volvo PTT 2.05.20 download source comes from internet, so enjoy on your own risk!
Which PTT version is tested OK and working 100%?
Here you go: Volvo PTT 2.04.87Why choose this version?
You can directly get the answer from below Volvo PTT 2.04.87 software list:
- Dev2tool (for programming parameters version 2 - older trucks)
- Developer tool Plus(Acpi+) (for programming parameters version 3 and 4 - newer trucks)
- Visfeed + Xml Editor
- Volvo/ IS File Encryptor/Decryptor
- Volvo Traing Files (Flash, PDF,Video) 3GB
Volvo VOCOM 88890300
VOCOM VCADS
UOBDII All rights reserved Volvo Tech Tool PTT 2.05.20 Free Download in Mega
OBDSTAR H110 VAG-I+C Immobilizer Car List
OBDSTAR H110 is first released device in china specially for MQB. Equipped with RFID ADAPTER, OBDSTAR H110
provides users with good solution to 4th and 5th generation of VW. With
combining immobilizer and cluster calibrate, it can be widely applied
to after market, auto repair shops, auto technicians, individuals.
OBDSTAR H110 VAG-I+C Immobilizer Car List:
(1)2 - 3.5 Generation Immo 17 Dashboard
17 Dashboard
25 Immobiliser(2)4 Generation Immo
Audi A1:NEC+24C64 2013, 2014.6-
Audi A3/TT/R8(CDC+24C32/3217/3297)
Audi A4 RB4 Audi A4 RB8
Audi Q3: NEC+24C64 2013 Models, 2014.06-
Audi Q7/A6L(C6): 9S12DT(G)128, 9S12DT256
VW/SKODA/SEAT: CDC+24C32
VW/SKODA/SEAT: NEC+24C32
VW/SKODA/SEAT: 2013 Johnson
VW/SKODA/SEAT: Motorola 9S12XHZ512
VW/SKODA/SEAT: NEC +24C64
VW/SKODA/SEAT: NEC+95320
VW/SKODA/SEAT: NEC+35XX
VW/SKODA/SEAT: Magotan/CC(3)5 Generation Immo Audi A4L/A5/Q5 Audi A6/A7/A8
VW New Touareg(4)REMOTE
09 Central control
B5 Central door lock(KWP1281)
46 Central comfort module(kwp1281) 46 Central comfort module(Canbus)
(5)Read PIN
17 Dashboard Jetta Passat Bora
Golf Sharan Polo Lavida 3.5
Sagitar 3.5 2007-, 2006
Touran 3.5
Caddy 3.5
VW 2007-
25 Immobiliser
01 Engine
Article from OBDSTAR Blog site: OBDSTAR H110 VAG-I+C Immobilizer Car List
Your Title
Recently,some customers sent email to OBD2 review on product Launch Easydiag.Here I put part of their reviews below,hope it will give your a understand in-depth.
If you find Launch Easydiag is out of stock,you can try some replacement products,such as Launch EZcheck,Launch M-daig....
I love Launch EasyDiag 2.0 Plus smartphone diagnostic kit; it does everything you really need without spending $1000+ for a real scanner.
This EasyDiag 2.0 came within 7 days. all is good, very happy with this kit a good investment.
Pros:
- Bluetooth
- allow me to use it on either android or iphone
My Ford Fiesta had a check engine warning light, and I used the EasyDiag 2.0 PLUS kit to find out that the MAP sensor needed to be changed.
I spent £15 on the new part and now the car runs great and the engine
light was deleted in seconds. The reason I went for this instead of a
Ford iCarsoft kit is so that when I change my car in future, all I need
to do is buy the software for my next car instead of buying a brand new
diagnostic kit.
- I used the EasyDiag 2.0 PLUS kit to clear an engine light from my C Class and was very impressed with the service.The only thing I noticed that it really does not do is bi-directional
reading but if you need that then you're a professional mechanic working
in a shop.Article from OBD2 Blog site: https://blog.uobdii.com/49-99-hot-launch-easydiag-2-0-plus-review-pros-and-cons/
This is a blog post with images
Images add a perfect touch to your blog posts and attract readers to open them. The first image from your content will be automatically used as a blog post thumbnail, so the right opening image can increase the attractiveness of your article.
Blog post with formatting tips for you
The introductory paragraph gives readers the main idea of what they can expect. It can be also used as a short preview in the blog post list. Different formatting will help it stand out from the rest of the texts. Read further to see how can you format your blog posts.