OBD2 Tool
http://www.uobdii.com/

Benz E200 check engine light, idle when the engine vibration, slow speed

Symptom

A Mercedes E200 configuration 271EVO engine and 722.9 transmission, mileage of 131670km. The car to replace the oil filter base, 4 days after the engine fault light, and idle engine jitter, the vehicle speed slow.xtool x100 pro

Troubleshooting and troubleshooting

The car replaced the oil filter base, disassembled the intake manifold, according to the initial phenomenon of the fault to determine the following reasons: the intake system in a vacuum tube leak or not installed in place; intake manifold leak ; Throttle does not match well, or is not installed in place; ignition problem; xtool ez500 oil supply problem.Because the car did not change the maintenance of the spark plug, VVDI MB Tool and the last into the store to check the spark plug attached to a lot of coke, and the phenomenon of burning the electrode, first with a new spark plug installed, the car after the engine or jitter. There is no problem with the spark plug connected to the diagnosis of the spark plug. Read the fault code: P0172 mixture (cylinder column 1) is too thick, the signal amplitude is greater than the maximum amplitude. The meaning of the fault code is the mixture is too thick, resulting in mixed gas is too thick because the main reason is too much fuel injection, too little intake or burning is not good. Follow the fault code to guide the actual value of the engine under idling conditions.VVDI Key Tool

The actual value of the rail pressure is 5440kPa (marked value is 4540 ~ 6540kPa), which will remove the problem of high pressure pump. Throttle downstream pressure sensor pressure value of 48.266kPa (standard value of 20 ~ 40kPa), the signal voltage is 1.0V (standard value is 0.5 ~ 0.7V). There are two reasons for its actual value: the sensor and its line problems; air intake system in a part of the leak. According to the circuit diagram to measure the sensor supply voltage of 5V, ground and signal lines are normal. Throttle upstream pressure sensor and the downstream pressure sensor, the two sensors are interchangeable, the actual value of the sensor is still incorrect, indicating that the sensor and its line is no problem. Next check the air intake system where there is no leakage,VVDI Key Tool.

In the first easy after the difficult principle, first check the intake system of each vacuum tube with or without leakage of the place, and then check the throttle, remove the throttle to see the seal is not damaged and crushed place, flap is not issued card , To save the throttle again after the replacement, with a diagnostic instrument to re-learn, taking into account the E-class 212 models in the diagnostic test when the voltage requirements are more stringent, when the battery voltage is lower than 11.6V when some of the elements of learning And the match may not succeed. Connected to the battery charger on the throttle to relearn, start the vehicle, the fault remains the same, remove the throttle problem,VVDI MB Tool.

Then focus on checking the intake manifold, remove the intake manifold to see its seal is intact, no abnormalities, but also in the seal on the sealant, and then installed in accordance with the standard torque intake manifold. Start the car, the engine or jitter, throttle downstream pressure sensor actual value is not normal. Re-order ideas, starting from the air intake step by step careful investigation, see whether the missing part. When the rear of the air filter to check the intake pipe, found that as long as the pull out of the intake pipe connected to the secondary air jet pump hose (below),MB SD C4 the engine does not shake, and the actual value of the throttle downstream pressure sensor Also fell to the normal range. Put the handle near the hose, can obviously feel the warm air blowing, smell like the exhaust gas from the cylinder.This tube is the secondary air jet pump inlet pipe, the secondary air jet pump is usually only in the coolant temperature between 10 ~ 60 ℃, the engine speed is less than 3000r / min, the engine is idle or part of the load. The secondary air jet pump draws fresh air from here and then switches the vacuum control secondary air injection valve from the intake manifold by the air pump changeover valve (Y32). The fresh air enters the row of the cylinder head with the secondary air injection valve Gas and exhaust gas to react, so that the three-way catalytic converter as soon as possible to achieve the working temperature, thus improving the warm-up process of emission performance. According to the working principle of the secondary air injection system, this tube should not be blown out of the air. There are two reasons for this phenomenon: the air pump switching valve (Y32) is always in the normally open state, the air pump switching valve (Y32) has been through the vacuum to open the secondary air injection valve; secondary air injection valve stuck, Open the state. Through the diagnostic device to observe the actual value of the air pump switch valve, has been in a closed state, and then through the diagnostic instrument to activate the open, close are normal, the exclusion is the air pump switch valve (Y32) problem. The following left the second air injection valve, and remove the secondary air injection valve and open and found the diaphragm was coke locked, can not be closed.Since the secondary air injection valve can not be completely closed, the exhaust gas is returned to the intake pipe through the piping of the secondary air injection system so that the pressure of the intake manifold is increased and the exhaust gas is then introduced into the cylinder.Because the entry of the exhaust gas, relatively fresh air will be reduced, so that fuel can not be fully burned, air-fuel ratio is not right, the engine jitter and reported mixed gas too thick fault. The secondary air injection valve carbon deposition clean, re-installed back, the engine running smoothly, the problem solved.The next morning to wash the car ready to pick up the goods, start the vehicle and found the vehicle just off the car immediately, and then start the second time, start time is too long, but after the start of the engine running very smoothly. Then start a few times, everything is normal. Stopped a dozen minutes to start again, the failure appeared. And then use a multimeter to measure the starting voltage of 10V, normal. The low pressure of the fuel system is measured at about 500 kPa (standard value 400 to 670 kPa). Connect the diagnostic device, analyze the actual value of the engine at startup, found that the actual value of the downstream pressure sensor is not normal, its value is 38.6kPa

(Standard value is 20 ~ 40kPa), close to the critical value. Will be the second air pump inlet hose unplugged and found a blown air, turn off after ten minutes and then start the vehicle again, everything is normal. Again remove the secondary air injection valve and find that the diaphragm is jammed again. Remove the coke after careful observation, the diaphragm has been deformed, off lax, it is easy to be coke locked.Replace the new secondary air injection valve after troubleshooting.

Fault summary

In the troubleshooting, we must comprehensively, CGDI MB Benz comprehensively and systematically consider, master the working principle of the engine system, according to the working principle of the possible parts of the failure to exclude one by one, careful analysis of the various failures and the actual value is very important Can help us find ideas and found that difficult to find the point of failure.

Lonsdor K518ISE program Volvo XC60 smart key

Lonsdor K518ISE key programmer is tested able to add Volvo XC60smart key and program new keys when all key lost via OBD. Lonsdor K518ISE will bring professional locksmiths a cost-effective choice comparing with the 4s shops who charge a higher cost.Tools and adapter to prepare:
Lonsdor K518ISE key programmer
RN-01
FS-01 probe boardBefore programming Volvo XC60 key, you need to read the security data of two modules (CEM module and KVM module), then directly add the key or program new keys via OBD.Part 1: Read the security data of two modules:

  1. CEM module (behind the storage box of co-pilot)
  2. KVM module (right side of the trunk)
There are two kinds of smart keys: 5 keys and 6 keys, both are 433MHZ frequency.
For 5 keys, before programming key, dismantle the CEM module and read the security data to backup.
For 6 keys, before programming key, dismantle both the CEM and KVM modules and read the security data to backup.
When we read CEM and KVM security data to backup, we need to use accessories of the adapter, RN-01 and FS-01 probe board.
Note: First time to use the adapter, we need to bind it with K518ISE. Go to the K518ISE home page and choose "Settings -> binding adapter", following the direction to finish binding.
One K518ISE host can bind up to 5 adapters, and the bound adapter cannot be bound to other K518ISE hosts. Once bounded, no need to bind again.Guide: How to read CEM security data
  1. Volvo's CEM are located under the co-pilot airbag on the left, remove the debris box, the new/old CEM box look the same, but with different circuits).
  2. For the old version, when opening the lid, in the back of the circuit board, please pay attention to the black column with blue circles, which are the four positioning points that need to match stably with the white column of RN-01 board.
Read CEM data with RN-01 board:Plug K518ISE host, adapter, and RN-01 board shown as below: Note: The circuit board is coated with insulating glue, it is required to use the washing plate water to wash off the blue area of the insulation coating in the contact point (solder joint) , or power can not go through , if the needle of RN-01 board is broken, it will do to wire in the corresponding locations.For the new version, the circuit is different, which requires to wire to read the anti-theft data, please refer to following guides to wire:

Note
: Connect power to read the data, it is needed to separate RN-01 board to the motherboard to prevent conduction; it is recommended that welding line should not exceed 15cm.How to Read KVM security data:
Volvo's KVM modules are located after the rear box, in the upside of the right rear wheel position(for 16 S60L car, it is recommended to dismantle from the right rear door to the wheel direction);
  1. After opening the module cover, it is firstly needed to use the washing plate water to wash off the blue area of the insulation coating, or power can not go through.

Read KVM data with FS-01 board:The positions in red circle are the 8-pin insertion points of FS-01 board:The connection among the K518ISE host, adapter and FS-01 board:Important Notes:
The reason why a part of the failures in Volvo KVM data reading because the chip model is different, then please do as below:
① Use programmer to read out the data (.bin file);
② Please contact and send the EEPROM data to K518ISE after-sales service, the engineers will convert the data into a dedicated file;
③ Connect K518ISE with computer and put the dedicated file into "file ---> feature_35" folder;
④ Following the operations to select the KVM data from the process.
Tips
  1. For 6 keys, during operation, you need to firstlyinsert the key into the key slot and then operate by following the directions.
  2. For key recognition failure, please make sure the smart key is not locked, as locked key cannot be programmed, the fresh new key generally will not be locked.
  3. K518ISE has identification & unlock functions, which will test and identify whether a key is an unused one or not. If the remote control is invalid after the key is programmed (on condition that the battery is well installed and the remote control frequency is correct), try to import the CEM security data to unlock the key and then program again.
Note: Only the key of this car or corresponding car can be unlock after reading the CEM security data.
4,When installing Volvo battery, please note that the two batteries are placed in an overlap way and separated by a white paper in the middle, so please do not just replace the above one.
Dismantling is also very simple, just remove the metal key, and gently pry with a not so sharp knife in the same place where the metal key lies.
Done.Article from Lonsdor K518ISE Blog site: Lonsdor K518ISE program Volvo XC60 smart key

Launch CRP129 reset Electric Brake on Renault Scenic II

Step-by-step display the procedure of Launch CRP129 reset Electric Brake on Renault Scenic II, I am sure it helps a lot.Connect Launch CRP129 OBD2 scanner with Renault Scenic via car OBD2 port.Insert key card into key slot and do not press the brake pedal.
Then, press the car Start button for 6 seconds.Power on the scanner and choose "Diagnostics".Go to "Replacement".And choose "Reset Brake".Select "Renault" car maker.Follow the tips to turn ignition on.Select "Scenic II" car model.Choose "Release" then turn on ignition and do not run car engine. This action OK!Back to choose "Apply" then turn on ignition and do not run car engine. This action OK!

Done! Launch CRP129 successfully reset Renault Scenic II Electric Brake!
This is what I got Launch CRP129, it is very impressive.

From Launch X431 Tool, post Launch CRP129 reset Electric Brake on Renault Scenic II (Procedure)

XTOOL EZ400 PRO, Xtool EZ400 & Xtool PS90 which is better?

XTOOL EZ400 PRO is different from Xtool EZ400 in the VCI box, XTOOL EZ400/EZ400 Pro is different from Xtool PS90/PS80 in the special functions.More about obd2 tool,pls visit:blog.uobdii.com

  1. Different:
1). XTOOL EZ400 PRO= Xtool EZ400 + VCI box
XTOOL EZ400 PRO is all-in-one machine, no need any more VCI box, so it is 2.64LB lighter than Xtool EZ400, lighter package means less shipping cost and easier to use.Attach Xtool EZ400 VCI boxAttach XTOOL EZ400 PROfull package (without the above Xtool VCI box) 2). XTOOL EZ400 PRO / XTOOL EZ400 functions < Xtool PS90
Xtool PS90 (10inch tablet with wifi and all function):
Full system diagnosis on all makes......confirmed
IMMO......confirmed
Odometer Adjustment ......confirmed
Special functions (Oil Reset/Engine Oil Light Reset, EPB Electrical Parking Brake Adaptation, TPS Throttle Body Adaptation,EPS Electric Power Steering Calibration, Gear Learning, ABS Bleeding , ECU Reset, Tire Pressure Warning Light Reset and Battery Reset.) ......confirmedXTOOL EZ400 PRO 7″ functions:
Full system diagnosis on all makes......confirmed
Special functions works: Oil Reset/Engine Oil Light Reset, EPB Electrical Parking Brake Adaptation, TPS Throttle Body Adaptation ...confirmed Launch X431

3).
XTOOL EZ400 PRO / XTOOL EZ400 is much cheaper than Xtool PS90
Xtool PS90: 1500 dollars to 2900 dollars (google to confirm)
XTOOL EZ400: 554 dollars
XTOOL EZ400 PRO: 479 dollars
SRC: http://www.uobdii.com/wholesale/xtool-ez400-pro.html
  1. Same:
  • Original Xtool products and update on Xtool official site xtooltech.com.
  • Full system diagnosis...... confirmed
  • Both can perform these special functions: Oil Reset/Engine Oil Light Reset, EPB Electrical Parking Brake Adaptation vehicle fix
  • One-year free update, one-click software update via WIFI
  • After-sales technicalsupport (Remote access).

That's all
UOBDII All rights reserved Compare XTOOL EZ400 PRO, Xtool EZ400 & Xtool PS90

XTUNER AM1011 Function List:

XTUNER AM1011 is released by XTUNER company which is a Multi-Language Scan Tool,and here China OBD2 engineer list the functions below:When the code reader boots up, the Home screen opens. This screen shows all applications loaded on the unit.
Following applications are preloaded into the code reader:SKP1000

  • ● OBDII/EOBD - leads to OBDII screens for all 9 generic OBD system tests.
  • ● DTC Lookup - leads to screens for diagnostic trouble code lookup.
  • ● Review Data - leads to screens for access to tested data files.
  • ● Print Data - leads to screens for access to printing function
  • ● About - leads to screen that shows information about the code reader.
  • ● Setup - leads to screens for adjusting default settings to meet your own preference when using the code reader.OBDSTAR
When Diagnostics application is selected from Home screen, the code reader starts to detect the communication protocol automatically. Once the connection has been established, a menu that lists all of the tests available on the identified vehicle displays. Menu options typically include:
  • ● Read Codes
  • ● Freeze Frame Data
  • ● Erase Codes
  • ● Live Data
  • ● I/M Readiness
  • ● O2 Sensor Test
  • ● On-board Monitor Test
  • ● Component Test
  • ● Vehicle Information
  • ● Modules Present
  • ● Unit of measure
  • More info about XTUNER AM1011 Scan Tool,pls visit obd2 website:
http://www.uobdii.com/wholesale/xtuner-am1011-obdii-plus-code-reader.html

Autel TPMS tool TS601 Price Cut Down

Exciting news: Autel TPMS tool TS601 price $495 incl. shipping (on www.uobdii.com), it's really a good price after you compared it with Amazon Aliexpress. It will be sent soon after paid, ship from Hong Kong, 3-5 working days delivery, one year free update on the internet via USB port, some users feedback they can't register with serial number doesn't exist, it is clone. Well www.uobdii.com is the real one, please feel free to use.As known TS601 is the most powerful TPMS tool among Autel TS501, TS601, most users prefer to TS601, for their difference, here a comparison table:

Autel MaxiTPMS TS601 Vs TS501 Vs TS401 Vs PAD Vs MS906TS

Here YouTube Video on, how to use TS601 to test clone create TPM sensor and
program MX-sensor:It will well pack come in a nice box.

Here collect several pieces of Autel TPMS tool TS601 Questions and Answers:
Question:
I have a tpms light on for my front driver side. will this read the possibly faulty sensor and program a new one if need be?
Answer: Edit: Just checked the tool and it describes the procedure for each vehicle. 350Z requires a tool with OBDII connection to load the ID's.
Question: can TS601 tool program the original ID #to the new sensor and relearn thanks
Answer: Can this tool program all car make and model accurate check for all sensor
Question:Is there any way to find out the coverage of cars this unit will work on? Ie. I have 2009 Subaru Outback
Answer:It is a amazing product and it does cover the 09 Subaru
Question:Will this work on a 2012 subaru impreza?
Answer: yes it can

All rights reserved by www.uobdii.com

Article from TPMS Blog: Autel TPMS tool TS601 Price Cut Down

BMW FEM/BDC Programmers: Yanhua, VVDI2 & BMW Explorer

Looking for BMW FEM/ BDC key programmer? Here top 3 ones are highly recommended: Yanhua FEM key programmer adapter, VVDI2,CGDI Prog & BMW Explorer. For which one better, go on reading.

Top 1: Yanhua FEM key programmer (Newest)

Yanhua FEM key programmer allows offline operation , safe and stable, easy to operate
No need tokens
Online Update: on http://www.autoemaster.com/ (Yanhua official site)Yanhua BMW FEM Key Programmer coverage (Up to 2017 year):
1 Series F20/F21 2011-2017
2 Series F22/F23/F45/F46 2014-2017
3 Series/GT F34/F35 2012-2017
4 Series F30/F31/F32/F33/F36 2014-2017
X5 F15 2014-2017
X6 F16 2015-2017

How to use Yanhua FEM key programmer?
Coming soon...
Top 2:VVDI2 5.0.0(Update next time)
Xhorse vvdi2 5.0.0 in Chinese can generate BMW FEM / BDC keys and reset odometer. For the English version of vvdi2 5.0.0, the function is not available yet, please keep an eye on www.uobdii.com banner or column "News & Notice".

Upload one picture of VVDI2 5.0.0 in Chinese authorized with "Generate BMW FEM / BDC keys" To enable "Generate BMW FEM / BDC keys", you need to pay or use 8000 points. Someone may think why the update need to charge, why not free, because the additional charge is to pay Xhorse engineers' efforts and after-sale service.How to use VVDI 2 5.0.0 to program key on FEM/BDC?
User manual and video will be uploaded here.
Have many BMW cars with FEM? Better own one VVDI2 firstly like this one:
http://www.uobdii.com/wholesale/vvdi2-with-basic-bmw-and-obd-functions.htmlTop 3: BMW explorer program key for BMW FEM /BDC
BMW-Explorer since version 14.05.08 allows users to program ignition key for FEM / BDC
Key programming into FEM / BDC is divided into several stages
1 Preparation of FEM / BDC thru OBD
2 Preparation of FEM / BDC using programmer (Reading BACKUP)
3 Programming FEM / BDC with BMW-Explorer via OBD
4 Write back BACKUP with the programmer
5 Key programming thru OBD
Paragraph 1:
It is necessary to perform a quick test , go to the FEM / BDC and click the "Key learning" button,
The program will check for a supported version of the unit, prepare the unit for the next procedure, and will display the message "Read Eeprom and upload in calc".
Paragraph 2:
Remove the FEM / BDC unit as described HERE. Disassemble the FEM / BDC unit as described in THIS SECTION.
Read 95128/95256 Eeprom (pictured in the upper right corner) using programmer
(Orange Xprog or others that supports Eeprom 95128/95256).
Download Eeprom into BMW-Explorer, and save EEprom and write it back into the FEM / BDC.
Paragraph 3:
Install the unit on the car in the reverse order of removal, and connect BMW-Explorer via OBD.
The car probably will not respond to the key, do not get scared!
Connect to FEM, press "Write keys", Explorer will propose to program the FEM / BDC, agree and wait for the programming to finish.
After successful programming, the program will write to you "Return the saved original Eeprom", then remove FEM again and using programmer, return the previously read contents of EEprom 95128/95256. Then you can install the unit back to the car.
Sometimes it is possible that after the last manipulation the FEM / BDC will stop responding to the diagnostics, then you need to flash this EEprom into the unit and program the unit with Esys or ISTA-P and start the unit preparation from step 1.
P.S: Follow the instructions and save your time.
Paragraph 4:
Connect to the FEM / BDC control unit using the BMW-explorer, press "Extra options" then "Key learning". Key programming window will open and will read the key data we need for programming.
If you have a working key, then you need to bring it to the emergency coil as pictured below and press the "Read crypto key" button.
About successful reading of the "Crypto" BMW-Explorer show "Crypto Ok" message.
If you do not have a working key, then you need to read the ISN from the DME and enter it into the "ISN from DME" window.
You can also enter 8 bytes of the "crypto" manually.
Now you can start to learn keys. To do this we must select a free track for the key and press "Learn key", bring a new key to the emergency coil on the steering column.
Supported ECU FEM:
swfl_0000155e_004_102_030, swfl_0000155e_004_102_040
swfl_0000155e_004_103_030, swfl_0000155e_004_104_040
swfl_0000155e_007_102_010, swfl_0000155e_008_101_030
swfl_0000155e_008_101_050, swfl_0000155e_008_101_070
swfl_0000155e_011_102_020, swfl_0000155e_012_104_010
swfl_0000155e_012_200_030, swfl_0000155e_014_102_040
swfl_0000155e_015_100_020, swfl_0000155e_015_102_020
swfl_0000155e_015_152_030, swfl_0000155e_015_154_010
swfl_0000155e_016_106_030
Supported ECU BDC:
swfl_00002419_005_016_130, swfl_00002419_005_016_140
swfl_00002419_005_017_092, swfl_00002419_005_018_031
swfl_00002419_005_019_040, swfl_00002419_005_019_101
swfl_00002419_005_019_120, swfl_00002419_005_028_060
swfl_00002419_005_028_160, swfl_00002419_005_028_170
swfl_00002419_005_028_245, swfl_00002419_005_031_110
swfl_00002419_005_031_200, swfl_00002419_005_042_030
swfl_00002419_005_042_050, swfl_00002419_005_042_070
swfl_00002419_005_118_030, swfl_00002419_005_118_050
swfl_00002419_005_118_140, swfl_00002419_042_100_040
swfl_00002419_052_010_030, swfl_00002419_052_030_010
swfl_00002419_052_040_010

Article Key Cutting Machine :BMW FEM/BDC Programmers: Yanhua, VVDI2 & BMW Explorer

Launch CRP129 Code Reader Customers Reviews

I have one small auto repair shop and my normal customers would like to drive their car to my shop to do DTC troubleshooting and do some reset things. I was looking for such a cheap and working tool. Then luckily I have Launch CRP129, it can meet all my requirements. I write my objective review on its performance and how it performed. Hope it helps.
Paid $229 free shipping on Launch CRP129, shipping took 3 working days to America.
Launch CRP129 tablet is compact and easy to take, the buttons are designed using fiber so comfortable to touch and rugged. It has 3.5" touch screen and clear to view.Hook it up to the vehicle, CRP129 device was quick to get going from the initial power up and it was also quick to operate. The response in moving through the menus and executing tasks was immediate. Downloading and running updates (which is partly down to internet connection speed) was reasonable.
CRP129 tablet is limited to cover all system, it only access to the basic 4 systems (ABS, ECU, Airbag and Transmission), however it supports 40 car models ( from USA, European and Asia)- it has a improvement comparing CRP123. Besides, I prefer CRP129 tablet to CRP123 because it can perform basic diagnostic function and also some reset maintenance functions incl. reset service maintenance lights, steering angle resets and release electronic parking brake. That fits my daily repair work.Attach here CRP129 tablet Data Stream Graphic Display, I like it, very clear display.CRP129 tablet meet my requirement to print out the diagnostic results. I and my customers can check it anywhere anytime when I use it, it is very good.
The last point I want to mention is it is available with also French and Spanish, so anyone whose mother language is French or Spanish, CRP129 tablet can't be much better to fit you.
You also can get more info from this blog:
http://www.launchx431v.org/

In a word:
I tested not all car brands it claims it can work; my overall impression to CRP129 is it really works great as it described.
From Launch X431 Tool, post LAUNCH CRP129 review - by small repair shop technician

Launch CReader 419 Reviews

I received Launch CReader 419 after 10 days i ordered it at Launch X431 it's small and light, plug and play, portable to use anywhere
http://www.x431tool.com/wholesale/launch-diy-scanner-creader-419.html I confirm the plug is connected well;all buttons are workable;and the port can be used no issuethe screen resolution is good to readand the speed, as the dealer says, fast and smartso far, I have used it for 2 weeks. Worked perfectly.
Read DTCs ...OK
Clear DTCs ...OK
Turns off Malfunction Indicator Light (MIL) ...OK
Read dynamic data streams ...OK
Read readiness status ...OK
Read freeze frame data ...OK
Read pending DTCs ...OK
Read permanent DTCs ...OK
Read vehicle information ...OK
Color and graphical display of data streams ...OK
Query DTCs ...OKI must say it's definitely worth every penny (€30 actually), very useful to for home use / personal use/ DIY users etc. Maybe more languages better for others (now English, Spanish, French, German). But for me, it does what i paid for.If someone is tired of ELM327, handheld CReader 419 launch should a good choice i think.

OBDSTAR X300M reset Benz models odometer via OBD

Exciting news!!!OBDSTAR X300M Odometer correction Tool is tested working to reset odometer on many Mercedes Benz models via OBD. It is a 100% truth, it's already tested by OBDSTAR qualified engineers, no lies.1. K line odometer reset Model (M2) for AUDI/VW/SKODA/SEAT are added.
2. VW Golf 7 models are added.
3. Chassis W169 for BENZ A serial by OBD are added.
4. Chassis W245 for BENZ B serial by OBD are added.
5. Chassis W204 for BENZ C serial by OBD are added.
6. Chassis W209 for BENZ CLK serial by OBD are added.
7. Chassis W207 (E-COUPE) for BENZ CLK serial by OBD are added.
8. Chassis W218 for BENZ CLS serial by OBD are added.
9. Chassis W212 for BENZ E serial by OBD are added.
10. Chassis X204 for BENZ GLK serial by OBD are added.
11. Chassis R197 for BENZ SLC serial by OBD are added.Besides, OBDSTAR X300 PRO3 and X300 DP are working too:

X300 PRO3 key master standard package

OBDSTAR X300 DP Full Package

How to use Launch CRP Touch Pro diagnose Ford Focus

Launch CRP Touch Pro is a great tool that I will show you some features. I have a 2002 Ford Focus, it has rough Idle problems, and I am going to use Launch CRP Touch Pro to diagnose the problem and show its practical actuation.Let's go to see some features we have.
It also has some pad buttons, it is very easy to use with the touch screen which is very incredible quick responsive to move.This is for Ford here.
On this screen, we can do Automatically search, manually select, manually reset service and F-650 / F-750 Test specification
I always find the vehicle by automatically search, which is quick than manually search.
And it's asking for the VIN number.
Read out faults: GEM (Generic Electronic Module) and RCM (Restraint Control Module).
As you can see, we have many systems to read state. And we are going to Powertrain Control Module, and asking Turbo charge = Not equipped.
As you can see, we can read fault codes, there is actually no fault codes because the check engine light isn't on.
Let's going to do some more challenging because we don't have code direction. you can see it can clear the codes, read the data stream.
Let's go to the data stream, and if you watch this previous video, I am hoping this thing how quickly and responsive compare with other tools.
As you can see we do have hundreds of parameters available here.Let's look at this "Throttle Position" and "Intake Air Temperature" and "Fuel Rail Pressure", it is very responsive.
Very important feature here is graphing, all the graphing display in the same page. Here you could click the graph
to see clearly, it is kind of nice.
If you can't understand the meaning, you could click the lower button to check it.
What I want to mention is to choose the below button to google for whatever, so really kind of nice feature.
So start the car, and I can tell it does has rough Idle problem for sure. So what I want to do is go back and read fault code.
There is no fault codes here.
So let's go to read data stream "Engine misfire currently detected"
Go to confirm the definite problem one by one...
Finally, choose "Engine Revolutions Per Minute" and "Fuel Rail Pressure", as you can see, definitely not fuel pump problem.All right,Launch CRP Touch Pro does meet the minimum criteria for the future's require to do the types of diagnostics.
so it is really really good consideration if you want to do some diagnostic. I'll say it is very responsive, very good communication.
And in my impression, Launch is very good Company, I have to say you could also get some support what happened issues.
From Launch X431 Tool, post Launch CRP Touch Pro diagnose Ford Focus 2002 Successfully

How to use KESS V2 read Nissan Pathfinder YD25 ECU

Good news for sharing:
Latest KESS V2 FW 5.017 with token reset button is now tested and released only $199 at China OBD2!
Below tested KESS V2 FW 5.017 to read Nissan Pathfinder YD25 ECU via OBD OK!Connect KESS V2 FW 5.017 ECU Chip Turning Tool with Nissan Pathfinder via theOBD2 port.
Open KESS V2 5.017 Ksuite 2.22 software.
Choose Manufacturer: Nissan, Model: Pathfinder
ECU type: 2005 YD25DDTI DENSO H1Select "ID" to first read Nissan YD25 ECU ID.DENSO NISSAN/MITSUBISHI TDI SH7058/SH7059Name the new ECU data file and choose where to store before ECU reading.
Switch off car dashboard, click OK to continue.
Then choose "READING" and switch on car dashboard. (And check the connection is OK)After communication 100%, click OK and proceed to read ECU.Now KESS V2 Firmware 5.017 read Nissan YD25 ECU Nissan Pathfinder successfully! It takes several minutes to 100% done!UOBDII All rights reserved New KESS V2 FW 5.017 read Nissan Pathfinder YD25 ECU How?

How to diagnose and solve Auto Cylinder Leak

Cylinder leak detection using the cylinder leak detector.The basic principle of the test is to use the compressed air filled into the cylinder, with a pressure gauge to detect the piston at the end of the compression at the end of the cylinder when the Yanhua DR-Key adapter pressure changes, to characterize the entire cylinder group of OBD2 sealing.That is, not only the seal of the piston piston friction, but also to characterize the intake and exhaust valve, cylinder liner, cylinder head and cylinder seal.(1) cylinder leak detector structure and working principleDomestic QLY-1 type cylinder leak detection Diagspeed MB Key device mainly by the pressure reducing valve, intake pressure gauge, measuring table, calibration orifice, rubber hose, quick change pipe fittings and inflatable mouth and other components, as shown in Figure 2-12 The In addition, there must be an external air supply, a pointer to the piston position and a piston positioning plate.The pressure of the external air supply should be equivalent to the cylinder compression pressure, generally should be 600 ~ 900kPa. Compressed air according to the direction of the arrow into the cylinder leak detector, the pressure from the intake pressure gauge display.WithAfter which it enters the cylinder at the end of the compression end through the pressure reducing valve,Fcar FVCI Passthru tool the calibration orifice plate, the rubber hose, the quick change pipe fitting, and the inflatable nozzle. The pressure change in the cylinder is shown by the gauge. The pressure changesThe condition indicates the seal of the cylinder block.Cylinder Leakage Diagnostic Parameter StandardFor the cylinder leak, China has not developed a unified diagnostic parameters. Auto Repair

QLY-1 Cylinder Air Leakage Detector In the instruction manual, for the engine of the domestic truck, when the inlet, the exhaust valve and the cylinder liner are well sealed, the cylinder seal condition (mainly refers to the cylinder piston) Judgments can be dealt with in Table 2-6. When the meter reading is greater than 250kPa,Cylinder piston with sub-sealing conditions meet the requirements, the engine can continue to use; when the meter reading is less than 250kPa, the cylinder plug with the deputy seal does not meet the requirements of the engine cylinder to be ring or boring cylinder. Transportation industry standard JT / T201-1995 "vehicle maintenance process specifications" in the vehicle before the second maintenance of the use of the reference diagnostic parameters of the standard requirements of domestic Dongfeng EQ1090 and the liberation of CA1091 car cylinder leak, When the cylinder piston is placed in the static compression top dead center position, the measured gauge pressure should be ≥ 250kPa.

SKP1000 Key Programmer vs.SuperOBD SKP 900

SKP-1000 price: $479
SuperOBD SKP 900 price: $379SKP-1000 wins in abilities!!!
->SKP900 key programmer supports auto key programming ONLY!
->SKP1000 key programmer supports auto key programming + special functions!SKP 1000 wins in immobilizer!!!->Clear key memory;
->Program keys, proximity keys, smart key, flip keys;
->Program after-market and OEM keys;
->Read keys from immobilizer memory;
(Read immo pin code)
->New mechanical key number programming;
->Vehicle identification key programming;
->Reset ECU & immobilizer;SKP 1000 wins in special functions!!!->OBD mileage adjustment
->remote controller
->oil/service reset
->throttle body adjustment
->EPB
->pin code calculation
->EEPROM chip read
->immobilizer initialization
->EEPROM/PIC adapter
->personalized settingsSKP1000 wins in operation!!->used with a stylus pen/ digital pen to input commands to a screen
->much easier & faster when using2017 SKP1000 wins in update!!-> firmware updatable (not only software)
-> software update available now and in future2017 SKP1000 wins in future cars!!->SKP1000 will be compatibility for future cars
->SKP900 stopped production and never works for new modelsSKP1000 wins in connection!->has USB2.0
->has a better TF card with a readerSKP1000 wins in package list!->has a Haima 7pin adapter
->has a power adapter
->has a stylus pen
->has a TF card with a reader

SKP1000 Blog All rights reserved SKP1000 Key Programmer vs.SuperOBD SKP 900

Launch X431 Pro Mini VS X431 PRO VS X431 V Wifi / Bluetooth scanner

Here a comparison table between Launch X431 Pro Mini and X431 PRO. X431 PRO is available with X431 Pro 7", X431 Pro 8" global version and X431 V 8"Tablet (Exclusive sale on some shops i.e www.x431tool.com)

Appearance Item X431 PRO 7inch X431 V 8 inch X431 Pro 8 inch overseas version Launch X431 Pro Mini

Item No. SP183 SP183-D SP167-B SP291 Price $719 $729 $799 $679 Avalibility out of stock Avalibility Avalibility Avalibility Update one-click update online for 2 years free one-click update online for 2 years free one-click update online for 2 years free one-click update online for 2 years free Automotive Diagnostics √ √ √ √ Remote Diagnosis √ √ √ √ Recording and playback √ √ √ √ special function √ √ √ √ Waveform Display √ √ √ √ VIN Identification √ √ √ √ feedback √ √ √ √ Diagnostic Software LAUNCH Vehicle Coverage Inquiry System: http://qcar.x431.com/ OS Android Android 4.2 Android 4.2 Android 5.1 SIZE 7-inch Tablet,1024X600 8" 1280 x 800 IPS display with 189 ppi 8 inch Tablet 6.9 inch 1280 x 720 CPU Dual core 1GHz Quad core 1.3 GHz quad-core 1.3 GHz Quad core 1.3 GHz RAM 512MB 1 GB 1GB 2GB Capacity (internal / SD card) 2GB 16GB (expandable by up to 32 GB) 16GB 16GB Battery 3000mh, rechargeable polymer lithium battery 4200mh rechargeable polymer lithium battery 4290 mAh 3.7V/3000mh rechargeable polymer lithium battery Pixels : 2 mega rear and 0.3 mega front Front-facing 2 MP camera and rear-facing 5 MP

camera with 1080p HD video recording Front 2 mp / Back 5mp Front-facing 2MP camera + rear-facing 5MP camera Connectivity WIFI/Bluetooth Wi-Fi: WLAN 802.11b/g/n
Bluetooth: Bluetooth 4.0 WiFi/Bluetooth Wi-Fi: WLAN 802.11b/g/n, Bluetooth: Bluetooth 4.1 In conclusion:
Launch X431 Pro Mini is the smallest in size and weight, but perform as the same functions as X431 Pro tools. More importantly, it is cheapest, price only $679.X431 Pro 8 inch overseas version VS X431 V 8 inch tablet: they are the same one and performs as the same functions on same car brands, but labeled with different name ("V" and "Pro"). Recommend you order X431 V 8 inch tablet, it is cheaper than the overseas version.The old X431 PRO 7inch is out of stock and be replaced by the 8inch one.
From Launch X431 Tool, post Launch X431 Pro Mini VS X431 PRO VS X431 V Wifi / Bluetooth scanner

Xhorse VVDI Key Programmer Products Introduce

In this article I will introduce Xhorse VVDI Series products to you.The Xhorse VVDI Key Programmer is famous China Key Programmer.

VVDI MB BGA TooL Benz Key Programmer

1. Support BE key, read password and prepare new key via IR. 2. NEC V051,V057 support on board get password 3. All NEC keys support on board write and erase 4. Password calculate:support BGA keys,NEC keys(include 51,57version)etc.,work fast. 5. Support renew EIS and ELV 6. Support write EIS and ELV 7. Support online generate key file 8. Unlock ELV function will be released soon. 9. Renew other control modules function will support soon
Xhorse VVDI PROG Programmer

The built-in update software allows user to update VVDI Prog firmware timely.
High-speed USB communication interface enable the software automatically connect.
Smart operation mode: the possible causes of error will be listed
Reserve ports: for future update.
The self-test function enable you check if the machine works well.
Can supply power via USB cable, the software will automatically prompt if the external USB power supply is needed.

VVDI2 Commander Key Programmer

1. This VVDI2 Full Package Contains PSA Function, AUDI Generation 5, BMW OBD Fucntion and BMW CAS4+ Functions Already, No Need Other Authorization
2. VVDI2 Full Package Covers All the Functions of VVDI, VVDI 5th IMMO Adapter, BMW Multi Tool & CAS Plus for BMW Multi Tool
3. Support VW, Audi, BMW AND Porsche
4. Update Online Free Lifetime
5. Latest Version: V4.2.5

VVDI Key Tool Remote Key Programmer

1.Latest version: V2.3.9,Firmware Version: 1.1
2.Xhorse VVDI Key Tool remote maker supports most common remote types in the market; it is reliable and easy to use.
3.VVDI key tool remote generator can perform these functions:edit transponder, clone transponder, test frequency, clone Remote, generate remote, generate garage door remote controller, unlock smart card etc.
4.In a word, Xhorse VVDI Key Tool is a device with multi-functions.
5.With VVDI Key Tool Adapters(SK203-F), can renew different kind of original used remote key(The Adapters need to buy separately,not include in the package). If you need VVDI Key Tool with adapters, please choose SK203-B+SK203-F on our site.
6. Specially for America Cars, if you mainly dealing with other vehicles, could choose SK203-B.Here is the french website version
http://www.eobdii.fr/

WinOLS definitely better than ECM TITANUIM(Feedback)

It is clear that a car is best done with WinOLS if you have the give, but if you leave a car to schedule early in the afternoon and pass it to pick up as the limit at the last minute and WinOLS not give for that car. How long do you have to search the map and try to identify and program until it fine?
Which better Winols and ECM TITANIUM

That's the problem WinOLS without we would take forever to locate and map to map and define their similar and it takes longer to modifyWith Ecm Titanium you leave the essential potential maps to make a normalita repro without squeezing the most of the engine, maps advance, correction, singles, boot and other we all know that if you know not to touch them better not make it clear not appear because you can fuck the engine or turbo pump.The problem of ecm titanium is that poorly defines the axes of the maps but for me it is no problem because I edit the driver and change the dimensions of X axis and Y to make it look as real as possible and then apply I conversion factors relevant to Z.Then if I have to look for other important maps that the program does not reflect in their drivers, do you make them yourself, I look in 2D or 3D and is very easy to select the memory location from where it starts to where it ends the map and define their axes as with any other program.My conclusion is that if you know how a map and as I touch it, the two program can go well but WinOLS v1.500 has more advanced options and is more accurate, but I think a change is slower to use when you start with a new ECU do not know.Another thing is when you bring a car and you leave him time to do it well get all the juice to the engine and everything is perfect, things change.So i think that if a person does not know how the parts of an engine and the engine ESN do work and not known as a map, leapfrogging is to have one or another program works.
More Car Diagnostic Software,pls visit China OBD2 website:
http://www.uobdii.com/wholesale/car-diagnostic-software/

Autel DS808 Frequencey Answer And Questions

Here a collection of Autel Maxidas DS808 Full Set Vehicle Diagnostic Tool Questions and Answers, hope it helps.


Question: Will this test the abs module on a 1995 chevy k2500 suburban with the diesel engine or can you recomend one that will?
Answer: on you need older otc
Question: Can you program BMW e63 keys
Answer: Sorry, it can't support to program BMW keys.
Question:Does this scanner do check engine lights abs lights and show live data??
Answer: Yes, DS708 can do it.
Question: Can u set Dist timing on 97 chevy
Answer: Yes you can, it's listed as knock retard in degrees. Set it close to 0 as you can get.
Question:Hi, does it have Australian vehicles?
Answer: only the Australia version DS708 can test Holden vehicle.
Question: Will this do as much as a snap on scanner?
Answer: You can search on YouTube where guys compare the different scanners between Snap On, etc.
Question:Ds708 have any advantage over the 808?
Answer: DS808 is much more advanced than DS708.The hardware of DS808 is more advanced, and DS808 covers more vehicles, and the vehicle software of DS808 has updated to 2016.
Question:What kind of modules can I access with this? Thank you in advance.
Answer: It is ccomprehensive diagnostic scanner, you can use it to access all ECUs and also special functions, like DPF, SAS, EPB, Key matching etc.
Question: What's the difference between ds808 and ms906?
Answer: DS808 is a smaller and stripped down version of MS906. The two models have the same function in software, but different hardware configuration. DS808 is configured with smaller screen and smaller battery, but DS808 is priced about $250 less than MS906.
Question: Can you increase your idle rpm with this scanner?
Answer: Do you mean the idle relearn function? It can be supported. But for some vehicles, the idle can be relearned by manual. So in order to confirm it, it is better you can provide us the detailed vehicle information, like Vehicle, year and Vin No.
Question: Will it diagnose suspension error indications?
Answer: Yes, DS708 can do it. Any other doubts welcome to contact me at any time.More information about Autel DS808,pls visit OBDII:
http://www.uobdii.com/wholesale/autel-maxidas-ds808k-full-set.html

How To Use Launch CReader 419 CR419

Launch CReader 419 Scanner is a car maintenance tool for home use (junior users). It features a full color display, meets all OBDII/EOBD protocols, provides commonly-used diagnostic functions, helps to rectify daily maintenance fault codes and it is cost effective.Here i put part of pitcure,if you want more pics ,visit the Source at end of article.Plug the CR419 Scanner 16pin port into the vehicle diagnostic socket.
Power on Launch X431 CR419.
This is CR419 function menu incl. Diagnose, DTC lookup, Tool setup and Help.Select "Diagnose", click the upper right green icon to enter system.Monitor status.
Select "I/M Readiness"
Back to select "Data stream", then select among "View all items", "Select items" and "View graphic item", press the "Up" & "Down" button to choose what you want to view.
Back to choose "On-board monitoring", some vehicles not support this function.
Back to choose "Vehicle information"
Back to check "DTC lookup"
Reset language among English, French and Spanish.
Check "Help" option.
Done.
In conclusion.
Launch CReader 419 CR419 scanner can't be more suitable for DIYers / Home use / newbie, since it can meet the daily diagnostic need and it is very easy to use. I suggest every car owner has one CR419 in the car, it is very small and suitable for your hand, no need computer or phone to run with. Don't you think?

From Launch X431 Tool, post DIY use Launch CReader 419 CR419 Scanner Review / Test Report

OBDSTAR TP50 TPMS Activator & Reset Tool Reviews

If you have tire pressure to active, reset data and diagnose, and if you are looking for an original handheld device, that is OBDSTAR TP50. OBDSTAR TP50 works on 315MHz and 433MHz Tire Pressure Sensor.OBDSTAR TP50 workable car list:
Generally speaking, OBDSTAR TP50 works on the vehicle brands from Asia, Europe, America and Chinese.
http://www.uobdii.com/upload/pro/obdstar-tp50-supported-car-list.pdfWhy choose OBDSTAR TP50 instead of Autel / Foxwell tools?

  1. OBDSTAR TP50wins price, $210incl. shipping worldwide.
  2. OBDSTAR TP50has more functions (active, reset data and diagnoseTPMS) than Foxwell NT1001 which is only an activator.

OBDSTAR TP50 features:
1.Fast and Stable Operation: CPU: ARM7, it will quickly take you from one page to another page.
2.HD Color Display Screen: The test result will display on TF 320x240
3.Shockproof and Durable Design: it is easy to hold on your palms not easy to slip.
4.Support High Capacity TF CardOBDSTAR TP50 package includes:
1pc x OBDSTAR TP50 main unit
1pc x Main Cable
1pc x SD Card
1pc x SD Card Reader
1pc x TP50 user manual
1pc x Charging power
1pc x Certificate

1pc x annular magnetArticle from OBDSTAR Tech Blog:OBDSTAR TP50 TPMS Activator & Reset Tool Reviews

http://www.uobdii.com/wholesale/obdstar-tp50-intelligent-detection-on-tire-pressure.html


What Is Auto Immobolizer System?

Car theft system refers to the system that prevents the car itself or the items on the car from being stolen. It consists of electronically controlled remote control or key, electronic control circuit,CGDI Prog alarm device and the implementation of institutions and other components.The earliest car door lock is a mechanical door lock, only for car driving to prevent the door automatically open and accident, only the safety of traffic, can not afford the anti-theft effect. With the progress of society, the development of science and technology SKP1000 Programmer and the increasing number of cars, and later the manufacture of cars, trucks doors are equipped with a key lock. The door locks only one door, and the other door is opened or locked by the door lock on the door VVDI Key Tool In order to better play the role of anti-theft, and some cars also equipped with a steering lock. The steering lock is used to lock the steering wheel of the car. The steering lock is locked with the ignition and is installed under the steering wheel, which is controlled by the key X431.That is, the ignition lock cut off the ignition circuit to turn off the engine, the ignition key and then left to the extreme position of the gear, the latch will be extended into the steering shaft slot, the car steering shaft mechanical lock. Even if someone will open the door and start the engine illegally, because the steering wheel is locked, the car can not be turned, it can not drive away, so played a car anti-theft effect Fcar F3-G.Some cars are designed and manufactured without a steering lock, but with another so-called crutches lock the steering wheel, so that the steering wheel can not turn, but also can play an anti-theft effect. Some cars in the transmission with a mechanical lock, the transmission lever is locked, so that the theft can not be linked to the car can not move. Ignition switch is used to turn on or off the engine ignition system circuit, according to a key to open a lock of the truth, but also played a certain anti-theft effect. As the car technology continues to develop, most cars are installed on the central door locks, that is, the car door locks and luggage compartment lock to achieve centralized control.

Launch Easydiag Diagnose Benz Wiht iPhone

Original Launch X431 EasyDiag OBD2 diagnostic tool is packed with no software but order any software you want in the official Launch DBSCAR site. Launch EasyDiag built in not USB cable but plug into the vehicle OBD port and communicate with Android IOS device via Bluetooth. Launch EasyDiag 2.0 PLUS is very easy to setup in the Android & IOS device (iPhone, iPod, iPad).X431 Tool guide on how to setup Launch EasyDiag 2.0 PLUS on Iphone for diagnosing Benz.
Part 1: Install APP for easydiag.
Click "App Store", search "easydiag"
Enter "Diagnose" menu.Click Login, for the first time you use, you need to register, to register the serial number and verification code are shown in the envelope as follows.Download completed. Now you can use the EOBD diagnosis software.
Overview Launch Easydiag vehicle coverage including: North America models, European car models
Select two car models to download: Benz and Euro Ford.
Software select.
Software download.
Part2: plug DBscar to diagnose Benz
Back to select Benz
Plug the bdscar adapter to the OBD port of Benz.
Diagnose benz
You can see we have SRS
Use Launch Easydiag to diagnose SRS
Select Benz, and get message "Bluetooth is not connected, please connect Bluetooth"
Make sure Bluetooth turn on, give some seconds until the Bluetooth is connected.
Click "Benz", Checking SmartBox.
Select vehicle manually
Select 211-E Class (As of 06/2006), then Sedan, then Diesel engine, then "Right-hand steering", then "E320 CDi", then "Control units", then select any of system including (Drive, Chassis, Body, Information and communication, Seats and doors, Air conditioning, here I select "Body",then "AB-Airbag" and click "Ok" when you get message reading "Please select "OBDSCar" Connector! then click "Ok" when it prompts Switch on ignition.Then click "Clear DTCs", you see Launch Easydiag can perform function: Read DTC,
Clear fault memory and read Data Stream. You read out trouble code with definition.
Clear fault memory, switch off ignition.
Launch Easydiag can read Current DTC/ Pending DTC as well as read current DTC with permanent Status.
Click "read Current DTC (Mode $03)" and get P0030 (HO2S Heater Control Circuit Bank 1 Sensor), so we need to go ahead to change sensor.
Click "Creat Word Report" at the left buttom corner. And go to menu and select "My Report"
From Launch X431 Diagnostic Scanner Tech Support, post How to Setup EasyDiag 2.0 Plus and Diagnose Benz with Iphone ?

SKP1000 Multi Function Key Programmer Replace SKP900 Perfectly

SKP1000 Tablet Auto Key Programmer a rebadged CI600 Plus (Chinese version),Perfectly Replaces SKP900 Key Programmer ,with one key upgrade,supports free update online for one year,small and easy to carry.

SKP1000 Multi-Function Key Programmer Function List:

Clear key memory;

Program keys, proximity keys, smart key, flip keys;

Program after-market and OEM keys;

Read keys from immobilizer memory

New mechanical key number programming;

Vehicle identification key programming;

Reset ECU& Reset immobilizer;

New remote controller programming;

Immo PINCODE reader for many vehicles and no need pincode when programming keys for many vehicles

Mileage adjustment via OBD;

With full and strong database for the most important vehicle makes;

Remote assistance

EEPROM chip read and immobilizer initialization;

EPB(Electric park brake);

Oil/Service reset;

EEPROM/PIC adapter

SKP1000 Key Programmer Car List:

BAIC, BENZ, BESTURN, BMW, BRILLIANE, BYD, CHANGAN, CHANGHE, CHERY, CHRYSLER(CHRYSLER/DODGE/JEEP), DFFENGSHEN, DFPV, FAW, FIAT,

FORD/LINCOLN, GEELY/HUAPU/SQYL,

GM(BUICK/CADILLAC/CHEVROLET/GMC/HUMMER), GREATWALL, HAFEI, HAWTAI, HIMIKO, HNMAZDA, HONDA/ACURA, HONGQI, HYUNDAI, ISUZU, JAC, JAGUAR, KIA, LANDROVER, LIEBAO, LIFAN, LUFENG, LUXGEN, MASERATI, MAZDA, MITSUBISHI, NISSAN/INFINITI, OPEL, PEUGEOT/CITROEN, PORSCHE, PROTON, QQROS, RENAULT, ROEWE/MG, SGMW, SMART, SSANGYONG, SUBARU, SUZUKI, TJFAW, TOYOTA/LEXUS, VW/AUDI/SKODA/SEAT, YOUNGLOTUS, ZZMAZDA, ZZNISSAN, ZOTYE;

More information about SKP1000,pls visit:

http://www.uobdii.com/wholesale/skp1000-tablet-auto-key-programmer.html

Automobile Power System Key working principle

The electrical power used in automotive electrical equipment is a DC power source, which comes from batteries or generators. The electrical system, which is connected by batteries, generators, regulators, charging status indicating devices, switches and wires, is called a power supply system (referred to as a power supply system).UCANDAS VDM2

The work of the automotive power systemThe battery and the generator in the MB SD Connect C4 power supply system are working in parallel. When the engine is in normal operation, the generator is powered by the generator and charged to the battery. At the time of starting, the battery supplies power to the starter. As the generator is driven by the engine through the drive rotation, when the engine speed changes, the generator output voltage will change. To meet the requirements of automotive electrical VAS5054A equipment and battery charging constant voltage, the power system are set within the voltage regulator to ensure that the generator output voltage stability in a certain range, to prevent the voltage fluctuation is too large and burn the electrical equipment. The charging state indicating means indicates the charge / discharge condition of the battery.The layout of automotive power systems VVDI2
At present, the power system on the car can be divided into 12V power system and 24V power system, and the general use of alternator and electronic regulator.Key Programmer
According to the electronic regulator installed in different ways, the power system layout can be divided into separate and integral two.key cutting machine
The distinctive features of the integral alternator power supply system are:
There is no longer a wire connection between the alternator and the voltage regulator. The system line is greatly simplified and the failure rate is greatly reduced. But the system failure can not quickly diagnose the failure of the car parts
CK100 Key Programmer
In recent years, with the people riding comfort, fuel economy, environmental protection requirements of the increasing, new electrical installations in the car has been widely used, the proportion of automotive electronic accessories increased significantly, such as a variety of Electronic control system (electronic control jet, electronic control automatic transmission, electronic control suspension), cruise control, car computer network.Diatronik OBD Tool

Some electromagnetic or electric actuators have also gradually replaced the hydraulic drive and pneumatic actuator, which greatly increases the load on the electrical system, which requires the car's power system to provide higher power.
http://www.car-auto-repair.com/

Magenta Pump Leakage Coolant Failure Case

Vehicle Information

Model: MAGOTAN 1.8T

Symptom:

MAGOTAN 1.8T new car more than 4,000 kilometers of water pump leakage of coolant, replace the pump after driving more than 1,000 kilometers, the pump once again leak antifreeze.Launch X431 Tool

Fault analysis and maintenance process Vpecker E4

1. When the vehicle travels 4011km, the station checks the leakage antifreeze. After checking the water tank, it leaks the antifreeze, removes the water pump and finds that the temperature inside the side outlet of the thermostat is damaged.Fcar F502

2. Replace the pump after the vehicle and travel about 1000km, once again complained about the antifreeze and leakage, check or water leakage at the pump antifreeze. Remove the pump to find the pump or in the side of the thermostat side of the outlet is damaged, the damage is the same as the first, (as shown below)

Professional DPF+EGR Remover 3.0

3. Because this vehicle is a new car and the damage location of the two pumps is roughly the same, analysis and pump quality problems caused by the probability is not that there should be other aspects of the problem, resulting in a series of damage to the pump.OBDSTAR TP50

On the form of damage to the pump, there are several possibilities:

1, the quality of the pump itself is a problem

2, the installation location of the pump problem

3, the installation of the pump cylinder surface protruding

4, there are external forces lead

4 because the water has been continuously damaged two pumps, analysis of the pump itself is unlikely to cause the problem; the new pump smear sealant, check the location of the pump installation; the engine block and the pump surface of the flatness of the inspection, Check the flatness normal.

5. In the process of inspection SBB Key Programmer found in the 2-cylinder, 3-cylinder injector at the bottom of a large number of yellow gasoline residue traces (as shown below), combined with the customer response sometimes in the cab can smell the smell of gasoline. Analysis of the traces should be leaking out of the gasoline traces, but the leakage of gasoline and water pump damage is it?

6. Further inspection VVDI found that the pump seal some swelling (see below), originally thought that the pump shell damage after the shell elongated, and now look at the petrol bedroom seal, resulting in swelling, and thus bulging the shell Body, causing leakage.

7. From the oil point of view 2 cylinder 3 cylinder position traces of gasoline traces more serious, remove the 2 cylinder, 3 cylinder nozzle, can be observed in the 3-cylinder fuel injector plug with gasoline, the surface of the gasoline flow trace. To determine the fault is caused by the 2-cylinder, 3-cylinder injector oil spill. The results replaced the 2-cylinder, 3-cylinder injector, and replaced the 1-cylinder, 4-cylinder nozzle seal.

8. After the vehicle is shipped, it is tracked, the next day the customer feedback feels good. And after a few days of customer feedback, in the cab and smell the smell of gasoline. Immediately about customers to check.skp900 programmer

9. Vehicles came to the service station, open the engine compartment, you can smell the smell of gasoline. Because the car's fuel injector installed in the lower part of the inlet, the eyes can not look directly to, in order to be able to accurately find the leakage point, learn the first two training lessons, in no hurry to disassemble and repair. The engine was in a state of fire, carefully observed in the bottom of the 4-cylinder injector formed gasoline droplets, check found in the top of the 4-cylinder injector, from the rails to leaking gasoline.

10. After removing the rails, observe that the guide rail has a vertical groove at the installation of the 4-cylinder injector. Sealed the place, put the rails up, into the gasoline, after a period of time, can be observed from the vertical at the vertical leakage of gasoline. (Pictured)

Failure analysis:

Because the 4-cylinder fuel rails have cracks, resulting in gasoline leakage, leaking out of the gasoline gradually immersed in the pump seal, the ring erosion swelling, resulting in damage to the pump, leakage antifreeze,

Troubleshooting:

Replacement of oil rails and pumps

Special tools / equipment: T10133 torque wrench VAS6150B OBD2

Maintenance Summary:

Water pump leakage is a more common fault, but the new car in the short term continuous damage we first met. The second maintenance, although checked out of the gasoline leak, led to the pump seal inflated, but did not find the root cause of the problem. On the one hand is the main location of the fuel injector installed in the lower part of the inlet, the naked eye can not be observed; the other hand, our inspection work is not enough detail. Need to sum up lessons learned. Do a good job of technical work, to study the investigation, root cause.

XTUNER Products Introduction:E3,X500,T1 and CVD9

Here comes the introduction of XTUNER products.Currently,XTUNER products include:XTUNER X500,XTUNER E3,XTUNER T1 and newest released XTUNER CVD9.

1.XTUNER X500 Special Function Diagnostic Tool1. Special Diagnostic Tool for Senior Maintenance Technician and owners
2. Powerful multiple functions like OBD2 Diagnosis,Oil Reset+DPF+Battery+ABS+EPB+TPMS+ IMMO+Injector
3. Program Keys by OBD2
4. Work with Android Mobile Phone, Easy to use2.XTUNER E3 OBDII Diagnostic ToolXTUNTER E3 OBDII Full Diagnostic Tool, replacement of Vpecker easydiag, covers more than 73 vehicles makes from US domestic, Europe, Asia, Australia and China. Communicate via WIFI. Compatible with Windows XP/7/8/10. 23 languages are available. Update online.1. Languages avaliable: Supporting 23 languages
2. Complete function including live data, ECU programming and so many others. 3. Unparalleled OBDII functionalities-support ALL 5 OBDII protocols and ALL 10 test modes. 4. Update: Automatically Wi-Fi update available in new software. 5. Can check out the year and model of the vehicles automatically and quickly. 6. Work stably and smoothly in high and low temperature environment. 7. OS: compatible with Windows XP/7/8/10. 8. With easy-to-use touch-screen and intuitive windows. 9. With brand-new design, the hardware features in stability and anti-interference.
10.Extensive vehicle coverage for more than 73 vehicles.3.XTUNER T1 Heavy Duty Trucks Diagnostic ToolXTUNER T1 Heavy Duty Trucks Auto Intelligent Diagnostic Tool is new professional Diesel scan tool released by TDINLTEL Tech. Xtuner T1 is with professional design, the hardware features in stability and anti-interference. The built-in over-voltage protection module is able to protect scanner and vehicle against accidental damage during checking.XTUNER T1 support both USB and WIFI connection for the VCI, provide you great convenient in diagnosing Heavy duty trucks. Free update online.1.Extensive vehicle coverage for heavy-duty trucks.
2.Complete function including DTC, DTC freeze Info, Live data, Actuation test and Special function.
3.Support standard protocol J1939, J1708 and J1587.
4.Communication: USB or WIFI connection for the VCI.
5.XTUNER T1 Update: New software update on the internet www.tdintel.com.
6.Supply OBDII and other 10 connector.
7.With brand-new design, the hardware features in stability and anti-interference.
8.The built-in overvoltage protection module is able to protect scanner and vehicle against accidental damage during checking.
9.Work stably and smoothlyin high and low temperature environment..
10.OS: Windows XP, Windows 7, Windows 8, Windows 10, which allows for more stable performance, better compatibility and expandability.4.XTUNER CVD-9 Commercial Vehicle Diagnostic Adapter
The Bluetooth XTUNER CVD-9 is the China' first commercial vehicle diagnostic adapter based on Android. CVD-9 is an electronic device that connects to the on-board ECU computers of truck, fire engine and motorhome, then transmits information via Bluetooth to the XTUNER CVD application. The CVD-9 adapter works with Class 3 - 8 heavy duty trucks with 9-pin/6-pin Dutch diagnostic port.1.Xtuner CVD-9 is the China first commercial vehicle diagnostic adapter based on Android, is a high-end and new style commercial vehicle diagnostic adapter developed by TDIntel.2.CVD-9 is an electronic device that connects to the on-board ECU computers of truck, fire engine and motorhome, then transmits information via Bluetooth to the XTUNER CVD application.3.The CVD-9 adapter works with Class 3 - 8 heavy duty trucks with 9-pin/6-pin Dutch diagnostic port. Workable Brands includes: Allison, Bendix, Caterpillar, Cummins, Detroit Diesel, Freightliner, Fuller, Haldex, International, John Deere, Mack, Mack 4, Mercedes Benz, Paccar, Pi, Psi, Takata, Volvo, Wabco, ZFMeritor, etc.4.XTUNER CVD-9 Adapter is made of industrial grade materials, is strong and durable.5.With Intelligent two-color lights, the color of CVD is not the same in different communication status, which can facilitate the customer to determine the communication status of CVD-9.More information about XTUNER products,pls visit OBD2 site:http://www.uobdii.com

XTUNER Products Introduction:E3,X500,T1 and CVD9

Here are Carprog FULL V9.31 FAQs and user feedbacks as a collection for you reference. Hope it helps.

Brief Introduction about Carprog
Carprog with all 21 items Adapters is a tool designed specifically to come to your rescue when you need to know the code of a car radio, a board or an immobilizer but not all. With Carprog you can make appointments for keys, change odometer, airbag reset but also others.

Frequently Asked Questions when buying Carprog FULL V9.31
Q: Is Carprog V9.31 the latest version Carprog Full? How can you send it to Russian?
A: Yes, Carprog V9.31 is 2014- latest Carprog diagnostic tool, and we can send it to via EMS or HK post.Q: I interesting in this programmer, my question is whether it can b e used to only correct odometers and few could change via OBDII, how long take to get to Mexico and what the cost of shipping.
A: The odometer correction function is not very good, this tool is professional in read and write ECU. About the different country shipping cost, you can evaluate it by yourself.

Frequently Asked Questions when using Carprog ECU Chip Tuning Tool
Q: Carprog FULL V9.31 is equipped with all Software's activated?
A: V9.31 Carprog comes with all Software's activated and all 21 items Adapters, Carprog Full V9.31 can do EEPROM and microcontroller programming.Q: I've an older version (8.21) but some functions are locked and need to connect to the official website for purchase and update.
A: The newest Carprog v9.31 has the same hardware version with V8.21, only upgrade the software to V9.31. and the machine may be locked. If you need newest software V9.31, please read here:
http://blog.uobdii.com/full-carprog-v9-31-software-free-download/

Q: My Carprog is locked what can I do to unlock it?
A: hello, pls tell us your order number? Do you update the main unit or use the others version?Q: Can Carprog Full Newest Version support Airbag Reset function?
A: Yes, Carprog support Airbag Reset function well, if you want to get more details about Airbag Reset cover models, you can visit here:
http://www.uobdii.com/wholesale/Carprog-Full.html

User Feedback:

  1. Highly recommend this product. I install it on Windows XP. The software is great. It's very easy to operate.
  2. I have used it to do airbag reset on my Renault, so convenient, I will Recommend it to my friends.
  3. Low cost with powerful function. Car radios, dashboards, immobilizers repair, it's awesome.
  4. I use Carprog ECU Chip Tuning Tool to read Cayenne PIN code quickly, and it needle sweeps and tests a lot of instrument clusters, if you into dash repairs.
Article from OBD2 Site: http://blog.uobdii.com/newest-version-v9-31-carprog-full-faqs-and-feedback/

How to detect Auto GND badness?

01 starter operation, if the battery grounding wire temperature is too high, even at the end of the phenomenon of red on the ground, indicating that the battery grounding wire contact bad.X431 Tool

02 in the case of non-charged measurement of the resistance value of the ground point, that is, with a multimeter of a table pen reliably connected to the wire, Yanhua Digimaster 3 another pen and metal parts of the body connected to measure the resistance between them, if there is resistance, The VXSCAN EL-50588

03 using simulated vibration method. For the suspected parts, you can in the vertical direction and horizontal direction gently shaking the line, to simulate the state of TOYO KEY OBD II vibration when driving the car, while observing the reaction of the relevant parts to determine whether the ground with Weld, loose, poor contact or wire break phenomenon.Autel MS906 If you shake a ground line when the fault reproduction or failure disappeared, indicating that the bad place where the ground here.04 When the circuit is energized, the voltage drop of the tapping point is measured with a multimeter. The reading should be as low as possible (close to 0). The method is to start the engine,Xhorse Condor XC-002 the use of multimeter DC voltage block, the red pen touch the generator output, black pen touch the engine body, measured a voltage value; and then the red pen touch the output of the generator, black pen contact The metal part of the frame, and then measured a voltage value. Under normal circumstances, these two voltage values ​​should be consistent. If the Autel MS908P former value is large, the latter value is small, a difference of 0.5V or more, indicating the existence of more than 0.5V voltage drop, it is by the engine body and the frame caused by bad grounding.
Detection of a point of the situation, it should be measured at the point of the power supply voltage, try not to measure the point of the negative resistance of the power supply, this is because the multimeter itself has a certain internal resistance, measured the resistance value of the larger error.

Launch X431 iCarScan and Vepcker Easydiag Test Report

Launch iScan accept a lot added options on that car again vpecker, for archetype on engine it can alone Launch X431 Diagun IVapprehend few ambit and it can apprehend and bright agitation codes thats it annihilation abroad on engine not even dpf regeneration, idiag accept added to action for that car, i activated on few added cars. I anticipate what it can do added with appropriate functions is for Toyota,Honda,Scion. But back it is aboriginal interface and software amount is ok for it (cost $210).Launch X431 Pro3

So for now vpecker OBD2 scanner is acceptable because it is even abundant faster than barrage and aboriginal for acceptable amount ($159), but not even abutting to Delphi or Barrage because of the functions that it cannot do.Launch X431 Pro3

Update
VPECKER Esaydiag and iScan accountability cipher clairvoyant are adapted online via Win XP~Win 10 system. Actual actual simple to update. So they can plan for all cars until 2015.Launch X431 Pad2
Language
Vpecker does bigger in accent compatibility, accoutrement 25 capital languages worldwide; while Barrage seems less, with 9 languages only. So if languages depend on customers, Vpecker will awning more.Launch X431 PAD 2

1. Full Diagnose Function:Launch X431 Diagun IV X431 diagun iv can diagnose the electronic control system of prevailing vehicle models covering Asian, European, American and China. Full range car models and full car system diagnose make it a professional automotive diagnostic tool. Diagnosis functions include: Read DTCs, Clear DTCs, Read datastream, Special functions etc; Ps. Vpecker language:
Italian, Chinese (Simplified), English, Chinese (Traditional), Japanese, German, Russian, French, Spanish, Portuguese, Polish,Turkish,
Dutch, Hungarian, Korean, Czech, Arabic, Indonesian, Persian, Thai, Vietnamese, Finnish, Swedish, Romanian, Bosnian, etc.
Launch language:
English, French, Russian, Japanese, German, Spanish, Italian, Portuguese, Chinese
That's it. I should say, anniversary one has its own claim and demerits, but both VPECKER Esaydiag and Barrage X431 iCarScan plan ok until now. A acknowledged acquirement from China.

How to solve Foxwell NT510 can not register?

UOBD2 customer service feedback: although most NT510 Scanner users operation no issure, he received a message saying "I am not able to register mine Foxwell NT510 OBD2 Scanner. The web site says my Serial Number does not exist. I went to the Update page, and this product does not exist. Only after going to the Product page was I able to find this scanner and I downloaded the foxwell Tools. I am not able to use this either because of "Network Error". And... There was some mysterious USB drive included in the package that also does not work. I'm pretty sure I just installed Putin's Democrat hacking software."First, please make sure the serial number and registered password are correct. Please pay special attention to letter "O" and number "0" and letter "I" and number "1" also. Even though there is a serial number on the back label, please always use the one you found by selecting Setup>About. What's more,please pay much attention to the model number,the model number is BMW_MINI_Scanner_14020SCH,which should Consistent with serial number.Solved:
Foxwell writes "Please click the link below to download and install the latest version Foxscanner 7.60 from our website: http://www.foxwelltech.com/product/item-169.htmlUp and running.
The newest version is required then is connects right away.
Put the sd card from the scanner into the USB adapter and plug into the PC. The Foxwell software will display what updates are available then updates the sd card. Put the sd card back in the scanner.More information about Foxwell NT510 OBD2 scanner,visit website:http://www.uobdii.com/wholesale/foxwell-nt510-multi-system-scanner.html

Smart CN900 Mini Updater V1.8 Free download

Recently,Smart CN900 Mini key programmer update to v1.8,and now uobd2 enginner share its Updater file to you.And upgrade your Smart CN 900 MINI,it wiil be echanced better performance.OBD2Free download CN900 Mini Updater V1.8
Operating system: Windows 7/Windows 8/Windows 10

Different between Smart CN900 MINI and CN900:

  1. ND900 is the China version CN900 car key copy machine. They perform same functions, differ in outlook. (PS, they use different 4D, 46 cloner box when copy 4D/46 chip). So Mini versionCN900 is aboard version and mini nd900 is domestic version instead.VDM UCANDAS
  2. CN900 mini inherited most of CN900's feature but mini one make car key copy more easierwithout connecting with 4D,46,G Decoder Cloner Box.
  3. Mini CN900 comes with built-in battery, do not need to attached to the power adapter.
  4. CN900 Mini support WiFi,Bluetooth and internet connection. The big size one do not support.
  5. CN900/ND900 Mini will replace big CN900 in the near feature.Vida Dice

Article from CN900 Mini:http://cn900-mini.blogspot.com/2017/04/smart-cn900-mini-updater-v18-free.html

Launch X431 V Update Guide

Launch X431 V (X431 Pro)/X431 PRO3 V+ wifi/bluetooth abounding Arrangement Automotive Diagnostic browse apparatus is the absolutely substitutes X431 IV and X431 Diagun III. Both X431 V and X431 V additional abutment one-click amend which makes your amend job abundant easier. Here is the apprenticeship on amend the software.Launch X431 Pad2
Step 1 Uninstall Launch X431 V+/Launch X431 V client X431 Pro Mini


Two means uninstall X431 V+ client
1) Bang red box apparent "1" above. Columnist on X431 V+ figure and advance it up to the debris bin. X431 Pro Mini
2) Bang "Settings" >> baddest Manage Apps>> X431 V+ >>Uninstall
Step 2 Delete Files XTOOL HD900
This is X431 V client.
Find out "FileManager" in the Application
Click Memory Phone
Delete all files in this folder, columnist on the files and Delete figure will appear.
Step 3 Download Newest X431V / V+ Client
Browse Launch website www.dbscar.com.
Click Category Product, baddest Launch V or V+.
Click "Download for Android" beneath X431 V angel to alpha download client.
Downloading, amuse delay patiently, book about 19MB.
Launch X431 Diagun IV
Double bang X431_V.apk
Click "Installation Package" afterwards complete download.
Click "Install"
Click "OK" if the arrangement prompts to update
Click "Cancel", because I haven't login.
Step 4 Login
Login with your CC amount and password
Read Claim, bang "Read"X431 Diagun IV
Select Bluetooth Serial Number
Enter into action menu. Note: Customer Management is for users to add friends, mechanics and engineers etc to babble and fix abstruse problem.Step 5 Download software
Click "Download", this is old software version.
Select the cars you wish to download. Note: the software downloaded from official website is the newest version
Click "following"
Click "Download"
After complete download, no car software found, back its old version, avenue the BDScar site, and login afresh to update.Launch M-diag

Step 6: Amend one car archetypal software
Login www.dbscar.com, accessible X431 V, it prompts to update, bang OK
Do not bang Cancel, let it download affairs automatically, it will yield beneath than 20minutes.
Click "Installation Package" afterwards complete download.
Click "OK" to alter old appliance and the above advice will be saved
Click "Install"
After complete download, the car models will display
Note: bigger not bang "One Key Update" to update
Click "Association" to brace Bluetooth
Click "following"X431 Pro
Click "Download"
After complete download, no car software found, back its old version, avenue the BDScar site, and login afresh to update.Step 6: Amend one car archetypal software Easydiag
Login www.dbscar.com, accessible X431 V, it prompts to update, bang OK
Do not bang Cancel, let it download affairs automatically, it will yield beneath than 20minutes.
Click "Installation Package" afterwards complete download.
Click "OK" to alter old appliance and the above advice will be saved
Click "Install"
After complete download, the car models will display
Note: bigger not bang "One Key Update" to update
Click "Association" to brace Bluetooth
Select the car models and software adaptation you wish to update.
Check software

Autel PowerScan PS100 Electrical System Diagnosis Tool

Autel PowerScan PS100 ebay / Amazon price over $70, and you could google and find many shops stock is unavailable. So pay less on a 10-year old famous shop www.uobdii.com is a reasonable choice.Pros to have Autel PowerScan PS100 on uobdii.com:

  • Stock Available
  • $69 only
  • 1 year warranty
  • Free after-sale tech support
  • Same functions to perform as you buy from ebay/ amazon.

Autel PowerScan PS100 capabilities (confirmed):
Performs every type of service including power injection, measurement, ground testing, polarity checks, continuity testing and components activation
Easy to read AVOmeter allows you to read voltage, current and resistance at the fingertip
With a flip of the power switch, you have an instant hot/ground lead for powering up electrical components like cooling fans, relays, etc.
Simultaneously uses the hot lead and the ground lead to activate components right in your hand
Instantly identifies positive, negative and open circuits
Tests for bad ground contacts instantly, allowing you to follow and locate shorts fast without wasting fuses
Instantly checks continuity of switches, relays and diodes.Autel DS808
Circuit breaker protected
Built-in Flashlight enables you to work in the dark
Audio tone indicator allows for no-look menu scrolling once users are familiar with menu tone assignment
20ft (extendable) cable provides excellent accessibility to test along the vehicle
Extremely easy to use and highly reliable

OBD All rights reserved $69 Autel PowerScan PS100 Electrical System Diagnosis Tool (in Stock)

How to clear the Auto engine carbon deposition

First, the risk of carbon deposition OBD2

(1) pre-combustion chamber to start the nozzle hole with carbon deposition will plug the nozzle make the engine start difficult;
(2) fuel injectors gather carbon easy to stuck fuel injectors cause the engine to stop the cylinder run or suddenly turn off;Carprog
(3) the top of the piston carbon deposition will form a lot of hot surface cause premature combustion and deflagration shorten the engine life;X431 TOOL
(4) Cylinder head with carbon deposition will reduce the engine cooling effect the engine's power and economy are greatly reduced;5054A
(5) spark plug too much carbon in the fuel after the wet equivalent to the spark plug between the electrode shunt resistance caused by spark plug leakage can not work;Autel DS808
(6) piston ring groove carbon deposition will make the piston ring backlash, backlash smaller _ even no gap; cause the piston ring cement loss of elasticity even breaking the piston ring and pull the cylinder;PS100
(7) valve duct and valve stem carbon deposition will accelerate the valve stem and valve duct wear and tear will even cause the valve stem in the valve tube within the hair astringent and stuck;
(8) valve and its seat on the working surface of the accumulation of carbon will cause the valve closed lax and leakage _ engine difficult to start, work weakness and easy to burn the valve and other undesirable phenomena.automobile repair guide  Second, the formation of glial and carbon depositionFuel in the storage, transportation process _ prone to oxidation reaction _ the formation of colloidal substances. These colloidal substances according to the solubility of gasoline can be divided into: soluble and insoluble in the gum.Auto key program

The insoluble gel, also known as the sediment _ it joins the fuel tank with the fuel tank _ will be attached to the fuel filter _ plug the filter medium _ to reduce the amount of oil _ to make oil shortage _ fuel atomization bad _ Resulting in flammable mixture dilution _ engine power and economic decline.The sol-gel enters the combustion chamber and the gasoline together. After burning, it will form many hard deposits on the intake valve, the piston top, the piston ring groove, the combustion chamber, the spark plug and other parts. Acceleration is not smooth _ idle instability _ stall, jitter, knock and a series of failures.When the engine is working, it is not possible to burn 100% of the oil that is fueled or flipped into the combustion chamber. The unburned part of the oil forms hydrochloric acid and resinous colloids under the catalysis of high temperature and oxygen. Adhesive to the surface of the part. The role of high temperature and further MASTER MST-500 concentrated asphaltene and oil coke and other complex mixture of the so-called carbon. Vehicle driving _ because the fuel in the glial and combustion after the formation of carbon deposition caused by the failure is more common _ great.Third, how to remove gum and carbon deposition Benz IR Key Program
In order to eliminate these failures, it is necessary to remove the coke from carbon and gasoline. However, many of the current methods used in the garage are to be cleaned and then cleaned. This method is not only time consuming and costly. It is not ideal, and it is not possible to remove the glial from the tank and the tank. It is also not suitable for today's car engines because today's car engines are assembled according to stringent process requirements in a clean, dustproof and ultra-quiet environment. After cleaning and re-assembly _ its power, sealing performance can not be compared with the original performance.It is no longer necessary to worry about this because it is only necessary to add a certain percentage of the fuel system in the fuel tank cleaning agent _ can solve the problems caused by carbon deposition. Fuel system cleaning protectors are gasoline and diesel general products , Designed specifically for the EFI car design, there are gasoline engine dedicated _ in the car can automatically remove the hard carbon deposition _ the engine's performance back to normal _ no longer by the disintegration of the pain _ can completely remove the carbon _ Reloading driving pleasure.After using this product to clean the coke, you should replace the petrol filter, because the jelly and tubing in the glial material and sediment are gathered in this _ if not timely replacement _ may cause poor fuel supply.

Launch EasyDiag 2.0 Plus Review

I love Launch EasyDiag 2.0 Plus smartphone diagnostic kit; it does everything you really need without spending $1000+ for a real scanner. This EasyDiag 2.0 came within 7 days. all is good, very happy with this kit a good investment.
Back to the Launch EasyDiag 2.0 PLUS Diagnostic Tool ($49.99 incl. shipping)
EasyDiag 2.0 Plus + OBD2 16Pin Male to Female cable ($54.99 incl. shipping)

Pros:
- Bluetooth
- allow me to use it on either android or iphone
- It has the obvious generic code reader/scanner but it also does engine, ABS, SRS, transmission and also does live date and color graphing. It will show you fuel trims etc.- Obvious ability to clear codes on all vehicle systems, interface is really easy to use too.
- reset the airbag light on my BMW X3, after I register successfully, I can choose BMW car brand software (to diagnose ALL systems), anyway the software is pretty easy to set up, and within about 10 minutes i was in the car and managed to find a problem was a seat sensor which i had replaced and then cleared the codes. The airbag light & message is now gone from the dash.
- The ABS light on my Jetta was illuminated and now it is clear (thanks to this kit and a new ABS sensor).
- Diagnosed a check engine light in my Audi (it needed an O2 sensor) and the ABS light in my Mercedes E Class (needed an ABS sensor).
- Very impressed with the vehicle coverage and what it can do.

More information aboout Easydiag pls visit OBD2 or X431 Tool website.

Mercedes-Benz S400 car ECO function can not be used

A driving distance of about 75,000 km, equipped with 276 twin-turbo engine Mercedes-Benz S400 sedan. Customer Response: The vehicle ECO function can't be used.mb sd connect compact 4
Fault diagnosis: after the car to start the car, no alarm on the instrument, connect the MB SD C5 diagnostic computer for rapid testing, the control unit are no fault code. And the customer road test to verify the fault phenomenon, found that the ECO indicator on the instrument has been yellow, driving for a long time will not turn green.5054A

Using the diagnostic computer into the engine control unit (ME) in the ECO state actual value, found that the actual value is normal, as shown in Figure 1.Foxwell NT510 Scanner

As the actual value shows normal, can not determine the fault range, try to engine control unit, transmission control unit, ESP control unit, before the SAM and after the SAM control unit are upgraded, the fault remains the same. Then after the throttle cleaning and 10min power failure, the fault still did not improve.OBD2
First look at the ECO start / stop function How it works: When the vehicle is at rest, the ECO start / stop function automatically turns off the engine and starts the engine as soon as the driver wants to start. Turning the engine off when the vehicle is stationary can reduce fuel consumption emission. The engine control unit continually performs system diagnostics and evaluates the system status of the ECO start / stop function. All systems involved in the ECO start / stop function continually check their status and send this status to the powertrain control unit (N127) and send them to the ME control unit via the CAN C1 (drive system area network). If the functional requirements are met, the "ECO" symbol in the dashboard is green to inform the driver that the ECO start / stop function is ready.Autel PS100
The function sequence of the engine auto stop is: If the following functional requirements are met, the ME control unit will shut down the engine. ECO start / stop function button lights up (that the system is fault-free and ECO start / stop function enabled); speed is 0; coolant temperature between 60 ~ 115 ℃; transmission oil temperature between 10 ~ 120 ℃ ; The engine speed is within the specified range; the range is at "D" or "flash"; the accelerator pedal is not operating; the running brake has been actuated until the vehicle is stopped; the brake booster has sufficient vacuum; the air suspension system , The auxiliary brake system and the distance control system do not perform the operation intervention function; the hood is closed: no collision signal; the steering wheel angular velocity is within the specified value range; the vehicle electrical system is in normal condition; the driver's door is closed and the driver's seat belt The temperature inside the car has been adjusted.http://www.x431tool.com/

OBDSTAR X300 DP VS XTOOL X100 PAD2 allegory table

In acclimation to accomplish you bright the aberration amid new accession OBDSTAR X300 DP and XTOOL X100 PAD2, actuality uobdii.com accord you a allegory table as below:
OBDSTAR X300 DP
XTOOL X100 PAD2OBDSTAR X300 DPXTOOL X-100 PAD 2
Operating SystemAndroid 5.1Android 4.4
CPUSamsung Exynos4418 A9 industrial-grade processor.X300M

Rockchip civil-grade processor
Storage spaceFLASH 16GFLASH 16G
RAM2G1G
Battery7400mAh4000mAh
Resolution1280*8001024*768
Screen size7 inch8 inch
HDMIAvailableAvailable
CommunicationWire/BluetoothOnly wire available
WIFIAvailableAvailable
Dimension215*147*30240*177*24
ShellThree proofing and industrial-grade carapace with elastic coatingCivil-grade
One key upgradeAvailableAvailable
One key enterAvailableNone
DatabaseBuilt-in databaseOptional, pay extra
Technical supportExpert account teamPincode inquiry7*24 hours automated analysis is accessible for a lot of pin codeManual inquiry
Fault diagnosisAll systems analysis are includedOnly basal disgnosis for four system。OBDSTAR RFID
Conclusion:
OBDSTAR X300 DP is above to XTOOL X100 PAD 2 in abounding aspects, such as faster CPU, bigger RAM, continued abiding array and college resolution.
OBDSTAR X300 DP has Bluetooth and One Key Enter functions while XTOOL X100 PAD 2 cannot support.
For OBDSTAR X300 DP it's no charge to analysis pin code, but XTOOL X100 PAD 2 charge analysis manually.OBDSTAR F102
And a lot of important is that XTOOL X100 PAD 2 can alone acquiesce you to analyze the basal four systems, but with OBDSTAR X300 DP you can analyze all systems!
OBDSTAR X300 DP abounding package
Immobilizer+ odometer adjustment+ EEPROM/PIC adapter+ OBDII+ ABS+ TPS+ SRS reset+ TPMS(low tire)reset+ Steering bend reset+ CVT learning/Value reset+ EPB+ Oil/service reset+ Array matching+ Analysis for Japanese and Korean serials (extra benefit function)
Article anatomy OBDSTAR Blog : OBDSTAR X300 DP VS XTOOL X100 PAD2 allegory table

Launch X431PRO & PRO3 Firmware Repair Guide

Step -by -step procedure on how to fix X431 PRO & X431 PRO3 Firmware.The software should try and do this automatically after an update, when you go to diagnose a vehicle. If the DBS connector fails to connect to the tablet, or you need to manually do a "firmware fix" then follow these instructions to ensure the latest version of firmware is currently installed on the DBS connector;Open the" Launch X431″ app

Tap the top left "three white lines" icon to open the side menu
Click on the Profile tab and then "Firmware Fix"
Firmware Fix screen will prompt instructions
Make sure DBS connector is connected to a vehicle with sufficient battery power
Firmware fix should have completed successfully.OBD2

If firmware fix did not finish or complete successfully, this means you already have the latest version of firmware, or you can try restarting the tablet and running through the "firmware fix" again.

Article from: Launch X431 Blog

How to solve auto air conditioning abnormal

Automobile air conditioning abnormal sound phenomenon (Daewoo car as an example) OBD2
Failure phenomenon for the lack of cooling, open the engine cover, run air conditioning and refrigeration systems, air conditioning compressor abnormal sound, and sometimes accompanied by significant vibration.Launch X431cause of issue
The circuit connection is loose, causing the clutch 4 to be jammed
Clutch line is quiet Launch X431 V 8
Clutch clearance is too large
The belt is loose
One of the two belts is broken at the same time
The compressor base is loose or worn Launch X431 V8
The compressor bracket is loose or
Compressor bearing is damaged
Tension wheel is damaged or lack of oil
Excessive refrigerant, causing liquid blow
Frozen oil too much, causing liquid hit
Compressor inside the internal (usually valve damage)Maintenance method
Connect the circuit as required
Replace the clutch coil
Adjust the gap to 0.4 ~ 0.8mm Reactor bearing damage Replace the clutch bearing
Tension belt
Replace two belts
Tighten the compressor base or replace the base
Fasten or replace the compressor bracket
Replace the compressor alone
Replace the tension wheel assembly or bearing
Emissions or recycling of refrigerants or refilling
Release the frozen oil
Repair or replace the compressor.

Mercedes-Benz S400 car ECO function can not be used

A driving distance of about 75,000 km, equipped with 276 twin-turbo engine Mercedes-Benz S400 sedan. Customer Response: The vehicle ECO function can't be used.mb sd connect compact 4
Fault diagnosis: after the car to start the car, no alarm on the instrument, connect the diagnostic computer for rapid testing, the control unit are no fault code. And the customer road test to verify the fault phenomenon, found that the ECO indicator on the instrument has been yellow, driving for a long time will not turn green.5054A
Using the diagnostic computer into the engine control unit (ME) in the ECO state actual value, found that the actual value is normal, as shown in Figure 1.Foxwell NT510 ScannerAs the actual value shows normal, can not determine the fault range, try to engine control unit, transmission control unit, ESP control unit, before the SAM and after the SAM control unit are upgraded, the fault remains the same. Then after the throttle cleaning and 10min power failure, the fault still did not improve.OBD2
First look at the ECO start / stop function How it works: When the vehicle is at rest, the ECO start / stop function automatically turns off the engine and starts the engine as soon as the driver wants to start. Turning the engine off when the vehicle is stationary can reduce fuel consumption emission. The engine control unit continually performs system diagnostics and evaluates the system status of the ECO start / stop function. All systems involved in the ECO start / stop function continually check their status and send this status to the powertrain control unit (N127) and send them to the ME control unit via the CAN C1 (drive system area network). If the functional requirements are met, the "ECO" symbol in the dashboard is green to inform the driver that the ECO start / stop function is ready.Autel PS100
The function sequence of the engine auto stop is: If the following functional requirements are met, the ME control unit will shut down the engine. ECO start / stop function button lights up (that the system is fault-free and ECO start / stop function enabled); speed is 0; coolant temperature between 60 ~ 115 ℃; transmission oil temperature between 10 ~ 120 ℃ ; The engine speed is within the specified range; the range is at "D" or "flash"; the accelerator pedal is not operating; the running brake has been actuated until the vehicle is stopped; the brake booster has sufficient vacuum; the air suspension system , The auxiliary brake system and the distance control system do not perform the operation intervention function; the hood is closed: no collision signal; the steering wheel angular velocity is within the specified value range; the vehicle electrical system is in normal condition; the driver's door is closed and the driver's seat belt The temperature inside the car has been adjusted.http://www.x431tool.com/

How to use Autel Autolink AL619 to read code

AutoLink AL619 is built to help you determine why the Malfunction Indicator Light or the ABS / SRS warning light is on. Featuring ABS/SRS system auto diagnosis, TFT color display, built-in speaker, troubleshooter code tips, the tool is truly ultimate in power and affordability. And in this article i wil share you how to use Autel Autolink AL619 to read code on your vehicle.1) Use UP/DOWN scroll button to select Read Codes from
Diagnostic Menu and press OK button. (Figure 5.3 )2) Use the UP/DOWN scroll button to select Stored Codes,
Pending Codes or Permanent Codes from the Read Codes
menu and press the OK button. (Figure 5.4 )If there is not any Diagnostic Trouble Code, the display indicates
"No (pending) codes are stored in the module!" Wait a few
seconds or press any key to return to previous screen.
NOTE: Permanent Codes function is available for merely
vehicles supporting the CAN protocols.
3) View DTCs and their definitions on screen.
4) If more than one DTC is found, use the UP/DOWN scroll
button to check all the codes.If retrieved DTCs contain any manufacturer specific or enhanced.(http://www.car-auto-repair.com)
codes, a "Manufacturer specific codes are found! Press any key
to select vehicle make!" message comes up prompting you to
select vehicle manufacturer to view DTC definitions. Use
UP/DOWN scroll button to select manufacturer and then press
OK button to confirm.If the manufacturer of your vehicle is not listed, use the
UP/DOWN scroll button to select Other and press the OK
button.More info about Autel Autolink AL619:http://www.uobdii.com/wholesale/next-generation-obdii-can-scan-tool-autolink-al619.html Article from OBD2 BLOG:How to use Autel Autolink AL619 to read code

VVDI Key Tool Programmer Function List

VVDI KEY Tool is a efficleancy device, imaple and easy for getting your work. Xhorse VVDI Key Tool supports nearly all common remote types that can be generated in the market. it can replace hand baby and CN900 Mini. VVDI Key Tool also add more transponders and function.Xhorse VVDI Key Tool Car Transponder Programmer VVDI Key Tool Replace Hand Babay and CN900 MINI


VVDI KEY TOOL Function List:

Transponder Generation:

Write most common transponder available in the market including 36, 46, 47, 60, 70

Transponder cloning:

Support 46 42 11 12 4D

Frequency & power tester:

Frequency test of 27-900 MHZ

Power test 300-450 MHZ

Remote cloning:

Rolling code & Fixed code

Generate remote:

More than 400 FCC ID types

Generate Garage door remote:

More than 100 types

Unlock OEM remotes:

NXP keyless & Prox Remotes
VVDI Key Tool Adapters, can renew different kind of used original remote key[The Adapters need to buy separately,not include in the package]

MB SD Connect C4 V2017.05 for offline programming

The offline programming has been switched off on DAS auto diagnostic tool beginning from DAS 012010. So now when you want to program a control unit for whatever reason you will need to go online to after sales platform which of course will require a dealer login and a password and only then you will be allowed to program the control unit. And this will be possible only if your control unit contains the software version older than the software version available. If the software inside the control unit is the already latest one and you still need to program it you will get a message saying that "No newer software was found". (Soon there will be a solution how to avoid this message).OBD2Here, we will tell you the offline-programming version.
The best version X431 Tool
Permanent version
Free versions This is the one highly recommend although the version is kind of old.
The package V2017.05 MB SD Connect C4 with DELL D630 laptop and preinstalled software is very convenient for users who do not ha ve DELL D630 laptop or do not want to install software. Besides, you need to buy additional setting up offline mode in old DAS software.
But you need set up WIFI and Lan cable connection by yourself if you want to do online programming. This package also includes the offline programming activation software.V2017.05 or the latest software for online programming:
NOTE: if you want to do online programming, you need the new software v2015.05 or the latest software. Our v2012.11 only support offline programming. If you want to do both online and offline programming, you are advised to have both v2012.11 software and v2015.05 or the latest software.

How to do offline programming V2012.11 software?Xhorese VVDI

Original super mb star c3 (not limited software version) do offline programming permanently XTOOL SHOP
Super mb star c3 is the most ideal version to do offline programming no matter which software version. But please enable the offline-programming function before use, then you can update it online and to use the newest star software for diagnosis.Offline programming for free-2015.05 star diagnostic software
Offline-programming function is available and free for all V2015.05 star diagnostic software incl. star c3, sd connect c4.Autel diagnostic tool

UOBDII All rights reserved (Best) MB SD Connect C4 V2012.11 for offline programming

CK100 auto key programmer V45.09 vs. V46.06 vs. V99.99

There are several versions of CK100 auto key programmers on the aftermarket: CK100 V45.09, V45.06 and V99.99.
NOTE: CK100 V45.02 auto key programmer is out off production in OBD2.

How to tell different CK100 auto key programmers? Here is the comparison table:

Item CK100 V45.09 key programmer CK100 V45.06 key programmer CK100 V99.99 key programmer Item No SK117-D SK117-C SK117-B Function key programming & pin code reading for some vehicle models Key programming Key programming Quality Clone best quality Clone high quality Clone good quality Update Can not be updated Token 2014 tokens, buy AT89C51CC03U NXP Fix Chip with 1024 Tokens Model year Till 2014.09 Till 2014.04 - Language English/ Italian/ Dutch/ French/ Spanish/ Portuguese/ Turkish Add vehicle model Adds vehicle 2014.04-2014.09 Ford, Honda and Toyota etc - Price US$ 139 US$134 US$95 In conclusion:

1. CK100 OBD2 auto key programmer V45.09 adds pin code reading function for some models, but V45.06 and V99.99 can not.
2. CK100 V99.99 enjoys cheapest price comparing with the other two.
3. According to customer's feedback, CK100 V45.09 and V45.06 have better quality than CK100 V99.99 auto key programmer.
Newest CK100 V45.06 pin code reading vehicle list:
1) For HYUNDAI PIN CODE
2) For KIA PIN CODE
3) For NISSAN BCM CODE
4) VAG PIN CODE SYSTEM1 (SYSTEM2,KOSTAL,MEGAMOS/DELPHI)
5) VAG 7-4 PIN CONV (PIN7,DEALER,IMPORTATORE,PIN4,DATA(00/00/2000),EXIT)
6) For GM PIN CODE ECM TYPE 1 (ECM TYPE 2,ECM TYPE 3,ECM TYPE 4,ECM TYPE 5,ECM TYPE 6
7) For CHRYSLER FOBIKCODE
8) For FORD KEYLESS ECODE (KEYLESS ENTRY CODE1,KEYLESS ENTRY CODE2)

http://www.uobdii.com/wholesale/ck100-key-programmer.html

VAS 5054A ODIS 4.0.0 PostSetup 30.0.10 free download

Newest ODIS 4.0.0 PostSetup 30.0.10 is verified working fine on VAS5054A interface (Chinese). The new release brings many new functions, fix bugs and many new VAG models.
Free download ODIS 4.0.0 PostSetup 30.0.10 torrent:
https://mega.nz/#!kkxEAaib!gXrR7d_nX7WpRv6X1YkRBiRoqp7F-VYKodnTP0ErtbM (100% works)Works on:

  • Windows 7 32bit works, other OS, try at your own luck
  • Works on VAS5054A interfaces:
Item No. SP33-BO, Bluetooth and OKI chip, $74.99 (OK)
VXDIAG VCX NANO VAS 5054, WIFI, $65.99 (OK)
Item No. SP33-B, Bluetooth, $59.99 (OK)
Item No. SP33-E, Bluetooth (AMB 2300), $99 (OK)
Item No. SP33-C (Fail)
Item No. SP33 (Under testing)
Item No. SP33-D (Under testing)
ODIS 4.0.0 PostSetup 30.0.10 installation easily with Youtube video:
Works on WIN7 32bitTwo testing picturesoverview: Release ODIS 4.0.0 PostSetup 30.0.10 upgrade content
New functions
  • Support for Windows 10 operating system
  • Performance optimization in the diagnostic entry
  • Detection of the VAS 6154 via subnets
  • Support for non-converging measurements in the GFF
  • Integration of the brand Bugatti
Bugfixes
  • Deviation in the EcuCom job for "ECU coding" KWP2000
  • ODIS installation error message - Could not call proc - Actia PDU API
  • Flashing with large data container, flash session is not started
  • Fuel system can not be vented // Level not readable
  • Flash abort ERROR PROGRAMMING at Audi A1 Bremse (TPI 2033217/3)
  • ODIS crashed when switching from USB to Bluetooth
  • Bluetooth connection type: No new connection was established after the diagnostic test was again within range of the VAS5054A.
  • Crash at application start
  • Update to 3.0.2 fails with ODS4010E: UpdateProcess failed with 11
  • Query error memory hangs: "Read control units (33%)"
  • Connection setup when changing from Bluetooth to USB takes too long
  • Authentication problem in WLAN infrastructure mode with RADIUS server
  • VAS 6154 is searched for on the wrong interface after completion of the diagnostic session
  • ODIS service SingleBuild installation, setup message "Runtime Error" for recovered testers
  • DA_14 in the AU48X DSD not possible
  • VCI 5054 Connection termination for Windows user change
  • ODIS Interface texts: German texts have been deleted from the XML files (vaudas.texts)
  • ODIS Service does not display the version of the diagnostic data for MAN in the correct format.
  • Calibration instruction must be adjusted
  • Buttons are displayed partially in the wrong language (German instead of English).
  • The symbol of the status icon changes with the ODIS close
  • Buttons to start the JRC and choose your own exam is missing
  • The date in disclaimer with EN-US language is not displayed correctly
  • In the installation dialog, the language en_US is displayed twice
  • Speech caseback leads to corrupt feedback file (invalides XML)
  • Vehicle project VW VIN can not be opened // ODS8003E Execution in system state PROJECT_OPENED not possible.
  • VCI-Number on DISS-protocol
Vehicle restrictions
  • For brand AUDI, the Flash mode is supported.
  • For brand Volkswagen PKW, the Flash mode is only partly supported. The usage is only allowed if described in TPI.
  • For all other brands, Flash mode is restricted.
Supported Vehicles
All supported vehicles are listed below.
Supported AUDI-Models
  • All AUDI-Models are supported.
Supported Volkswagen-Models
  • All Volkswagen-Models are supported.
Supported Volkswagen Nutzfahrzeuge-Models
  • All Volkswagen Nutzfahrzeuge-Models are supported.
  • Only immobilizer components in LT2 vehicles can be diagnosed.
Supported Seat-Models
  • All Seat-Models are supported.
Supported Skoda-Models
  • All Skoda-Models are supported.
Supported Bentley-Models
  • All Bentley-Models are supported.
Supported Lamborghini-Models
  • Only the following Lamborghini vehicle models are supported:
o Gallardo from MY09-MY14 (only for Immobilizer and Radio Pin)
o Aventador

o Huracán

OBD2 All rights reserved ODIS 4.0.0 PostSetup 30.0.10 torrent free download & installation on WIN7

EL50448 relearn Chevry Cruze TPMS

EL-50448 TPMS Reset Tool is special for GM Series vehicle.This article is the EL-50448 instructions on how to use EL50448 reset Chevry Cruze tire pressure monitor sensors. Tools you need: EL-50448 GM TPMS reset tool.
First,you need to get in car TPMS learn mode. 1.Set parking brake.
2. Turn ignition to ON/RUN (engine off)
3. Use the MENU button to select the VEHICLE INFORMATION menu in the DRIVER INFORMATION CENTER (DIC).
4. Use thumbwheel to scroll to the Tire Pressure menu item screen.
5. Press the SET/CLR button to begin sensor matching process. A message requesting acceptance of the process should display.
6. Press the SET/CLR button again to confirm selection. Second,use el50448 to close each valve stem. Note: Beginning with the left front tire, Once the sensor has been activated, the horn will chirp and the right front turn signal will be illuminated. You can then turn the vehicle off to exit "learn mode." (Starting with Left Front tire -> Right Front -> Right Rear -> Left Rear) Article form:https://uobdii.quora.com/EL50448-relearn-Chevry-Cruze-TPMS

VVDI MB Tool Power adapter data acquisition only 18 minutes

Good news! The newest VVDI MB Power adapter is designed to connect VVDI MB BGA toolfor W204 W207 W216 W164 data acquisition, aiming to save much time and take convenience.VVDI MB Tool Power adapter features:

  1. VVDI MB tool power adapter working on FBS3 type all key lost and gateway emulation, support C class, E class, CL, CLK, ML, GL, GLK types etc.
  2. VVDI MB Tool power adapter for W216,W164 2009- all key lost data acquisition, no need to re-plug IR adapter many times, without this adapter need to replug IR adapter 500 times.
  3. VVDI MB Tool power adapter support gateway emulation function, without real gateway you can use this adapter directly OBD communication with W164,164 2009-,W209,W211 (require special connection cables)
1.VVDI MB Tool power adapter only need 18 minutes to data acquisition for W204, W207 all key lost; without this adapter it will cost 150 minutes for data acquisition, save nearly 2 hours
  1. VVDI MB data acquisition adpater will keep updating more features.
How does VVDI MB Tool Power adapter work?
OBD2  All rights reserved
How to use VVDI MB Tool Power adapter for W204 W207 W216 W164 data acquisition?

VAS 5054A ODIS 4.0.0 PostSetup 30.0.10 free download

Newest ODIS 4.0.0 PostSetup 30.0.10 is verified working fine on VAS5054A interface (Chinese). The new release brings many new functions, fix bugs and many new VAG models.

Free download ODIS 4.0.0 PostSetup 30.0.10 torrent:
https://mega.nz/#!kkxEAaib!gXrR7d_nX7WpRv6X1YkRBiRoqp7F-VYKodnTP0ErtbM (100% works)Works on:
  • Windows 7 32bit works, other OS, try at your own luck
  • Works on VAS5054A interfaces:
Item No. SP33-BO, Bluetooth and OKI chip, $74.99 (OK)
VXDIAG VCX NANO VAS 5054, WIFI, $65.99 (OK)
Item No. SP33-B, Bluetooth, $59.99 (OK)
Item No. SP33-E, Bluetooth (AMB 2300), $99 (OK)
Item No. SP33-C (Fail)
Item No. SP33 (Under testing)
Item No. SP33-D (Under testing)
ODIS 4.0.0 PostSetup 30.0.10 installation easily with Youtube video:
Works on WIN7 32bitTwo testing picturesoverview: Release ODIS 4.0.0 PostSetup 30.0.10 upgrade content
New functions
  • Support for Windows 10 operating system
  • Performance optimization in the diagnostic entry
  • Detection of the VAS 6154 via subnets
  • Support for non-converging measurements in the GFF
  • Integration of the brand Bugatti
Bugfixes
  • Deviation in the EcuCom job for "ECU coding" KWP2000
  • ODIS installation error message - Could not call proc - Actia PDU API
  • Flashing with large data container, flash session is not started
  • Fuel system can not be vented // Level not readable
  • Flash abort ERROR PROGRAMMING at Audi A1 Bremse (TPI 2033217/3)
  • ODIS crashed when switching from USB to Bluetooth
  • Bluetooth connection type: No new connection was established after the diagnostic test was again within range of the VAS5054A.
  • Crash at application start
  • Update to 3.0.2 fails with ODS4010E: UpdateProcess failed with 11
  • Query error memory hangs: "Read control units (33%)"
  • Connection setup when changing from Bluetooth to USB takes too long
  • Authentication problem in WLAN infrastructure mode with RADIUS server
  • VAS 6154 is searched for on the wrong interface after completion of the diagnostic session
  • ODIS service SingleBuild installation, setup message "Runtime Error" for recovered testers
  • DA_14 in the AU48X DSD not possible
  • VCI 5054 Connection termination for Windows user change
  • ODIS Interface texts: German texts have been deleted from the XML files (vaudas.texts)
  • ODIS Service does not display the version of the diagnostic data for MAN in the correct format.
  • Calibration instruction must be adjusted
  • Buttons are displayed partially in the wrong language (German instead of English).
  • The symbol of the status icon changes with the ODIS close
  • Buttons to start the JRC and choose your own exam is missing
  • The date in disclaimer with EN-US language is not displayed correctly
  • In the installation dialog, the language en_US is displayed twice
  • Speech caseback leads to corrupt feedback file (invalides XML)
  • Vehicle project VW VIN can not be opened // ODS8003E Execution in system state PROJECT_OPENED not possible.
  • VCI-Number on DISS-protocol
Vehicle restrictions
  • For brand AUDI, the Flash mode is supported.
  • For brand Volkswagen PKW, the Flash mode is only partly supported. The usage is only allowed if described in TPI.
  • For all other brands, Flash mode is restricted.
Supported Vehicles
All supported vehicles are listed below.
Supported AUDI-Models
  • All AUDI-Models are supported.
Supported Volkswagen-Models
  • All Volkswagen-Models are supported.
Supported Volkswagen Nutzfahrzeuge-Models
  • All Volkswagen Nutzfahrzeuge-Models are supported.
  • Only immobilizer components in LT2 vehicles can be diagnosed.
Supported Seat-Models
  • All Seat-Models are supported.
Supported Skoda-Models
  • All Skoda-Models are supported.
Supported Bentley-Models
  • All Bentley-Models are supported.
Supported Lamborghini-Models
  • Only the following Lamborghini vehicle models are supported:
o Gallardo from MY09-MY14 (only for Immobilizer and Radio Pin)
o Aventador

o HuracánOBD2 All rights reserved ODIS 4.0.0 PostSetup 30.0.10 torrent free download & installation on WIN7

SKP900 review Honda Nissan Toyota Mazda Chevy OK

Here is 03.2017 SKP900 Key Programmer tested OK review for sharing:
SKP900 successfully program keys for Honda Nissan Toyota Mazda Chevy... Car list as below!Autel auto scanner
03.2017
SKP-900 Key Programmer car list update (Tested)

Chevy Equinox 2007 IMMO3 Launch X431

Chevy Silverado 2011 IMMO3
Chevy Silverado 2014 Camero 12 New Structure
Chevy Impala LS 2006-2007 IMMO3
Chevy Monte Carlo 2007 IMMO3
Chevy Cruz 11-15 - Camero 12 New Structure
Dodge Charger 2008 IMMO1 ADD KEY
Dodge Charger 2016 IMMO (RFH) ADD Key Need Pin
Dodge RAM 1500 2012 - Add Key
Dodge Grand Caravan 2005 - NO AKL NEED PIN
Ford Fiesta H94 2014 all key lost works
Ford Fusion 2010-2012 - Mustang Key - Add Key
Honda Accord 2000 - IMMO1 ALK
Honda Accord 04-07 IMMO1 ALK NONPIN
Honda Civic 2006 IMMO2 AKL
Honda Civic 2010 - IMMO3 AKL Xhorse VVDI
Honda Accord 2011 ALK IMMO3
Honda Accord 2014 - Keyless2
Hyundai Azura 2007 - IMMO4.2
Infinite i30 SYSTEM-OLD-IMMO-NATS5.0
Jaguar S-Type 2003
Infiniti QX56 2007 - NS > Key1
IMMO1>IMMO>SYS>AKL (2 Keys)
Jaguar S-Type 2006 IMMO3 AKL XTOOL Diagnostic Tool
Jaguar XF - 09-12 Add Key
Jeep GC 2001-2004 - IMMO (KEY)
Lexus GS300 2006 SmartKey2 > Reset Key > Add Key
Dodge Durango 2012 pulled PIN
Mazda CX-7 2007 - CX7 Menu
Mazda RX8 2004 - Mazda 8 IMMO
Nissan Altima 2006 - NS > Key1 - Key Adapt (Need Pin)
Nissan Altima - SmartKey 13- Read BCM - Adapt Keyless
Nissan Maxima 2003 - OS > IMMO > NATS5.0
Nissan Rogue 2011 all key lost new structure key 2 add keys works
Nissan Titan 2008 - NS >Key2>Key Program
Toyota Scion TC 2007 - IMMO1 AKL
Toyota Solara 2005 - IMMO 1 ALK
VW JETTA 03 - (SYS4 PINCODE) Key Match SYS1 or 2Note: SKP900 now is only $399! Lowest price at uobdii.com!
http://www.uobdii.com/wholesale/superobd-skp-900-key-programmer.html

BMW E-sys ENET Cable Reflash ZGM(solved)

I have successfully reflashed my 2001 F11 BMW ZGM system by using E-Sys from OBD2 and ENET cable from China. The total cost is very cheap. Here I would like to share is a quick guide on remaping the system.car repairI bought the BMW ENET Cable from a Chinese seller, no problem hooking it up to my car and laptop. The E-Sys software I first download is with 3.23.4 version, but got an error when using this version - my first attempt is to flash ZGM failed initially with the following

error:Code:

MCDDiagService id=240900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgMode, service=RC_GAC - Routine Control Get ActualConfig, description=error: timeout, link=Physical request to ECU with address 0×10>I found a few other threads mentioning possible solutions which are
Solution1
Use direct connection via gateway URL instead of via VIN to tcp://ip address of your car:6801 eg tcp://169.254.30.100:6801
Solution2

In Tal Processing ' Parameters uncheck "Switch gateway(s) to programming mode"In my case both options did not work with E-Sys 3.23.4. I then tried E-Sys 3.22.5 and was able to flash ZGM at the first attempt.If you want to download BMW E-sys click this article:BMW E-sys Free download

Notice!

I inform you that I am no expert on the subject and I am not stating or encouraging you make any modifications to your car by yourself. The information provided here are for information only as they were all taken at random sites on the internet and can be accessed publicly. You should be aware that I have no responsibility for what may happen to your car and any change to be held occur solely at your own risk.Hope this helps anyone.
UOBDII All rights reserved BMW E-sys ENET Cable Reflash ZGM(solved)

VXSCAN Ford TPMS Activation Tool Car List

Ford TPMS Sensor Training Tool Activation tool (8C2Z 1A203-A) as used by Ford to train the TPMS sensors on new vehicles or after a tire rotation. Use this tool to train OEM sensors so the TPMS warning light is not illuminated.

VXSCAN Ford TPMS Activation Tool Car List:2007-2014 Ford F-150
2008-2015 Ford F-250 F-350 F-450 F-550 Super Duty
2007-2015 Ford Mustang
2007-2014 Ford Edge
2006-2015 Ford Escape
2008-2015 Ford Expedition
2006-2016 Ford Explorer
2008-2015 Ford Flex
2008-2015 Ford Taurus
2008-2015 Ford E-150 E-250 E-350 E-450 Econoline Vans
2008-2015 Ford Fiesta
2008-2015 Ford Focus
2008-2015 Ford Fusion
2008-2011 Ford Crown Victoria
2011-2015 Ford Transit Connect
2006-2011 Ford Ranger
2007-2015 Lincoln MKX
2007-2015 Lincoln MKT
2008-2015 Lincoln MKZ
2008-2015 Lincoln MKS
2008-2015 Lincoln Navigator
2008-2011 Lincoln Town Car
2007-2008 Lincoln Mark LT
2006-2010 Mercury Mountaineer
2006-2010 Mercury Monterey
2006-2011 Mercury Mariner
2006-2011 Mercuy Grand Marquis
2006-2011 Mercury Milan More information:http://www.uobdii.com/wholesale/tpms-sensor-training-tool-for-ford.html

Multi Diag Access J2534 Pass-Thru Car List

ACTIA MULLER Multi-Diag ACCESS J2534 XS is high performance equipment, il diagnoses all major brands, and is a user-friendly software that will quickly make you a "Pro Diag"!


Multi diag ACCESS J2534 Car List:On more than 45 brands:
Alfa-Romeo, Audi, Autobianchi, BMW, Cadillac, Chevrolet, Chrysler, Citroën, Dacia, Daewoo, Daihatsu, Fiat, Ford, Honda, Hyundai, Jaguar, Kia, Lada, Lancia, Land Rover, Lexus, Maybach, Mazda, Mercedes, MG, Mini, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Proton, Renault, Rover, Saab, Seat, Skoda, Smart, SSangyong, Subaru, Suzuki-Santana, Toyota, Volkswagen, Volvo, Zastava... More info about Multi Diag ACCESS J2534: http://www.uobdii.com/wholesale/multi-diag-access-j2534-pass-thru-obd2-device-latest-version.html

Free download BMW Rheingold ISTA 4.03.21 ISTA-D for BMW ICOM

Here uobdii.com offer you free download links of newest BMW Rheingold ISTA 4.03.21 Standalone+ +SQLiteDBs + Delta Database. Hope it helps and also try on your own risk!BMW Diagnostic Tool

Free download BMW Rheingold ISTA+ 4.03.21 Standalone +SQLiteDBs +language package:
https://mega.nz/#F!4Msz2RgL!jvZdlqN3SF75Z5rIRnWnYgBMW ISTA 4.03.21.18572.msi (NO SQLiteDBs)
BMW_ISPI_ISTA-APP_4.03.21.18572
https://mega.nz/#!YxVAwAaL!vglnpcrLzUR5GZnejxOEoes4-HC13f3FUBlOqc1C-DoFree download BMW ISTA 4.03.21 Delta Database:
(EN-DE-Global-Meta)
BMW_ISPI_ISTA-DATA_DELTA_4.03.21.istapackage 121MB
https://mega.nz/#!nJ8XyZZB!iZ7tn_6-geNMICmudHBTjeAJ4yuVhbj3B8cqPRXFWH0BMW_ISPI_ISTA-DATA_DELTA_en-GB_4.03.21.istapackage 378kb
https://mega.nz/#!3ZcVzDxB!pg97aDWK3jY6yCDTW3n3Se1KXK7Ovnz3i1ZkRbHsFnABMW_ISPI_ISTA-DATA_DELTA_de-DE_4.03.21.istapackage
https://mega.nz/#!74FHFACC!vXaMcWJjma8E01YFaf0YBuObIeF9s2WoccNSWZe2PSwBMW_ISPI_ISTA-META_4.03.22.xml 17kb
https://mega.nz/#!6NUS0bQI!aCxykkVKs3F6WxzMWrt6Cnezy7vwHmLP-H7PLhk998sRequired interfaces of BMW ISTA Rheingold 4.03.21:
BMW Rheingold BMW ICOM A2
BMW Rheingold 4.03.21+BMW ICOM A3
BMW Rheingold 4.03.21+BMW ICOM Next
BMW Rheingold 4.03.21+BMW INPA K+DCAN USB interface
BMW Rheingold 4.03.21+BMW ENET cableSoftware details of BMW ISTA Rheingold 4.03.21:
Module (ECU) errors reading and clearing
Gearbox (transmission) and engine adaptations erasing
Fuel injectors control, correction amount real time viewing, injector registering
Engine mountings testing
Mass air flow (MAF) testing and registering. Whole air system testing
EGR system control and testing
Turbocharger and related components control and testing
Diesel particulate filter regeneration (DPF)
Battery replacement
Oil change and service interval reset
Wiring diagrams, live data, repair instructions, technical documents etc
Programming, vehicle retrofit, mirror coding, FSC codes adding or updating etc
And many more other functionsOperating system of BMW ISTA Rheingold 4.03.21:
Windows 7 (32-bit or 64-bit)
Windows 8 or 8.1 (32-bit or 64-bit)
Windows 10 (32-bit or 64-bit)Hardware requirements of BMW ISTA Rheingold 4.03.21:
Processor (CPU): min 2.2 GHz Dual Core or 4.4 GHz Single Core CPU (Summary of Cores or Threads should be more than 4.4 GHz)
Memory (RAM): min 4 GB
Hard drive (HDD): min 250 GB free space on disk C: before installation
UOBDII All rights reserved Free download BMW Rheingold ISTA 4.03.21 ISTA-D for BMW ICOM

VXSCAN Ford TPMS Activation Tool Car List

Ford TPMS Sensor Training Tool Activation tool (8C2Z 1A203-A) as used by Ford to train the TPMS sensors on new vehicles or after a tire rotation. Use this tool to train OEM sensors so the TPMS warning light is not illuminated.

VXSCAN Ford TPMS Activation Tool Car List:2007-2014 Ford F-150
2008-2015 Ford F-250 F-350 F-450 F-550 Super Duty
2007-2015 Ford Mustang
2007-2014 Ford Edge
2006-2015 Ford Escape
2008-2015 Ford Expedition
2006-2016 Ford Explorer
2008-2015 Ford Flex
2008-2015 Ford Taurus
2008-2015 Ford E-150 E-250 E-350 E-450 Econoline Vans
2008-2015 Ford Fiesta
2008-2015 Ford Focus
2008-2015 Ford Fusion
2008-2011 Ford Crown Victoria
2011-2015 Ford Transit Connect
2006-2011 Ford Ranger
2007-2015 Lincoln MKX
2007-2015 Lincoln MKT
2008-2015 Lincoln MKZ
2008-2015 Lincoln MKS
2008-2015 Lincoln Navigator
2008-2011 Lincoln Town Car
2007-2008 Lincoln Mark LT
2006-2010 Mercury Mountaineer
2006-2010 Mercury Monterey
2006-2011 Mercury Mariner
2006-2011 Mercuy Grand Marquis
2006-2011 Mercury Milan More information:http://www.uobdii.com/wholesale/tpms-sensor-training-tool-for-ford.html

Free download BMW Rheingold ISTA 4.03.21 ISTA-D for BMW ICOM

Here uobdii.com offer you free download links of newest BMW Rheingold ISTA 4.03.21 Standalone+ +SQLiteDBs + Delta Database. Hope it helps and also try on your own risk!BMW Diagnostic Tool

Free download BMW Rheingold ISTA+ 4.03.21 Standalone +SQLiteDBs +language package:
https://mega.nz/#F!4Msz2RgL!jvZdlqN3SF75Z5rIRnWnYgBMW ISTA 4.03.21.18572.msi (NO SQLiteDBs)
BMW_ISPI_ISTA-APP_4.03.21.18572
https://mega.nz/#!YxVAwAaL!vglnpcrLzUR5GZnejxOEoes4-HC13f3FUBlOqc1C-DoFree download BMW ISTA 4.03.21 Delta Database:
(EN-DE-Global-Meta)
BMW_ISPI_ISTA-DATA_DELTA_4.03.21.istapackage 121MB
https://mega.nz/#!nJ8XyZZB!iZ7tn_6-geNMICmudHBTjeAJ4yuVhbj3B8cqPRXFWH0BMW_ISPI_ISTA-DATA_DELTA_en-GB_4.03.21.istapackage 378kb
https://mega.nz/#!3ZcVzDxB!pg97aDWK3jY6yCDTW3n3Se1KXK7Ovnz3i1ZkRbHsFnABMW_ISPI_ISTA-DATA_DELTA_de-DE_4.03.21.istapackage
https://mega.nz/#!74FHFACC!vXaMcWJjma8E01YFaf0YBuObIeF9s2WoccNSWZe2PSwBMW_ISPI_ISTA-META_4.03.22.xml 17kb
https://mega.nz/#!6NUS0bQI!aCxykkVKs3F6WxzMWrt6Cnezy7vwHmLP-H7PLhk998s

Required interfaces of BMW ISTA Rheingold 4.03.21:
BMW Rheingold BMW ICOM A2
BMW Rheingold 4.03.21+BMW ICOM A3
BMW Rheingold 4.03.21+BMW ICOM Next
BMW Rheingold 4.03.21+BMW INPA K+DCAN USB interface
BMW Rheingold 4.03.21+BMW ENET cableSoftware details of BMW ISTA Rheingold 4.03.21:
Module (ECU) errors reading and clearing
Gearbox (transmission) and engine adaptations erasing
Fuel injectors control, correction amount real time viewing, injector registering
Engine mountings testing
Mass air flow (MAF) testing and registering. Whole air system testing
EGR system control and testing
Turbocharger and related components control and testing
Diesel particulate filter regeneration (DPF)
Battery replacement
Oil change and service interval reset
Wiring diagrams, live data, repair instructions, technical documents etc
Programming, vehicle retrofit, mirror coding, FSC codes adding or updating etc
And many more other functions

Operating system of BMW ISTA Rheingold 4.03.21:
Windows 7 (32-bit or 64-bit)
Windows 8 or 8.1 (32-bit or 64-bit)
Windows 10 (32-bit or 64-bit)

Hardware requirements of BMW ISTA Rheingold 4.03.21:
Processor (CPU): min 2.2 GHz Dual Core or 4.4 GHz Single Core CPU (Summary of Cores or Threads should be more than 4.4 GHz)
Memory (RAM): min 4 GB
Hard drive (HDD): min 250 GB free space on disk C: before installation
UOBDII All rights reserved Free download BMW Rheingold ISTA 4.03.21 ISTA-D for BMW ICOM

OBDSTAR X300M and UPA Correct Mileage for New Fords

To correct mileage on new fords, if via OBD OBDSTAR X300M Mileage Programmer is the best option, if via eeprom UPA is working OK.


  1. Mileage correction on new fords via OBD by OBDSTAR X300M
OBDSTAR X300M costs 269USD and works fine, tested it ok on:
Ford Tourneo 2015 H9S12EXQ384
Read ori Value ok
Focus 2013 OK
Ford fiesta 2012 2016 OKHere attach a testable list that OBDSTAR engineer test ok and users can find in the function menu:
FORD
Ford
Crown Victoria
2005-
C-MAX
2012
E250
2008-2009
E350
2008-2009
E450
2008-2009
Ecosport
Type 1
Type 2
Edge
2015-
Small color meter
Big color meter
Escape
2008-2012
Expedition
2007-2010
2011
Explorer
2007-2010
2004
F150
2006-2007
F250
2006-2007
F350
2006-2007
F450
2006-2007
F500
2006-2007
F550
2006-2008
Fiesta
2013-
Type 1
Type 2
-2012
Five Hundred(500)
Flex
2008-2012
Focus
2013-
2009-(Multifunctional screen)
//-2008(Smaller screens)
2005-2008
Freestar
2006-
Freestyle
2005-
Kuga
2010
2012
2012-
Color meter
Monochrome meter
Merc Mariner
2008-
Mondeo
2011-2013
Monochrome screen meter
2 pointer color meter
2007-2010
Monochrome screen meter
4 pointer color meter
Navigator
2007-2010
2011
New Mondeo
Small color meter
Big color meter
Monochrome screen meter
S-MAX
2007-2010
Monochrome screen meter
4 pointer color meter
Town car
2005-
Taurus
2015-(Big color meter)
2008-2009
2004
Lincoln
MKZ
2015-(Big color meter)
  1. If you are skilled and not correct mileage by OBD, any Ford is a very simple job, direct to eeprom or micro with for example UPA. It will take about 20 minutes maximum for any of them.

UOBDII Odometer Adjustment Tool All rights reserved OBDSTAR X300M and UPA Correct Mileage for New Fords

Which one VAS5054A is suitable for you?

Enter subtitle here

There are 5 kinds of VAS5054A, therefore some first-time users may be confused...they all seem the same, not sure if there is a difference, which one is best...... In order help them to sort them out, OBD2 engineer make a comparison table as follows. SP33 SP33-B(Cheapest) SP33-BO SP33-C(Best) SP33-D(Newest) Supported Protocol K line (ISO9141-2)
High-speed CAN (ISO 11898-2)
Low-speed CAN (ISO 11898-3)
J1850 (SAE J1850)UDS K line (ISO9141-2) High-speed CAN (ISO 11898-2)
Low-speed CAN (ISO 11898-3)
J1850 (SAE J1850)
UDS
PWM Protocol (they are equipped with OKI chip) Workable Car Models Support most Volkswagen group car models including: VW, AUDI, SKODA, SEAT Bentley and Lamborghini Workable Car Years Generally, cover from 1996 - 2013 year Function All VAS 5054A share the same function. As a universal diagnostic interface, VAS 5054A can read and erase ECU fault codes, including Check Engine, ABS, SRS, transmission system, Radio, heating, etc. Turn the check engine light off. Bluetooth All VAS 5054A support Bluetooth, the Bluetooth interface connects the vehicle with a notebook, desktop PC or test system. The range of the wireless Bluetooth connection is 2 to 5 meters, depending on the environment and the type of Bluetooth adapter used on the PC side. Language English, Japanese, Portuguese, Romanian, Korean, Dutch, Polish, Turkish, Spanish, French, Italian, Croatian, Danish, German, Swedish, Finnish, Slovenian, Czech, Russian, Greek, Chinese Upgrade When the newest software is available, contact us to send you download link or CD. OS Requirement Windows XP(xp2/xp3) Conclusion: l Another important difference is their price, range from $54 to $99.
l Most users prefer to choose the best quality one Item No. SP33-C
l Item No. SP33-D is the newest one, but an increasing number of users buy it
l Item No.SP33-B is the cheapest one.
In a word, which one VAS5054A to buy, it depends on your budget and requirement. UOBDII Auto Diagnostic Tool All rights reserved Which one VAS5054A to buy?

MB SD Connect 4 local and administration parameter settings

Most users have problem with MB SD connect4 local area connections settings and configuration settings. In the following parts, I will show you how to do these settings.

Step one: set SD connect 4 local area connection Internet Protocol (TCP/IP) Properties Launch X431
IP address as: 172.29.127.119
subnet mask: 255.255.0.0

Step two: SD connect4 configuration change
Click "configuration" then a windows named "Warning" apears, says "Caution! Changing the configuration can impair the fault-free functioning of the system. Do you want to change the configuration? Xhorse VVDI
Select "Yes"

Step three: SD connect4 MUX register configure setting
Click "MUX" button, then in the multiple choice box, please click "Register/Configure"

Step four: Select the name for SDCONNECT
Select the name for SDCONNECT as 4 XTOOL

Step five: SD connect4 WLAN parameter road setting
Set WLAN parameters, Road including: ID address, Network screen, SSID (network name), Encryption, key/
ID address: 192.168.2.200
Network screen: 255.255.255.0
SSID (network name): Road24h
Encryption: WEP/Hex
key:aaaaaaaaaaaaaaaaaaaaaaaaaa

Step six: Sdconnect toolkit device configuration
SDconnect Toolkit administration information conclusion including:
General information, WLAN conficuration, LAN configuration Autel Tool

Watch video on MB SD Connect Compact 4 local area connection and administration parameter settings at:
http://www.youtube.com/watch?v=Zo2jpewQSYIOr directly browse
http://www.uobdii.com/wholesale/mb-sd-connect-compact-4-star-diagnosis.html
then selects column "Video" to watch how to set SDconnect 4 local area connection and administration parameter.
Article from:https://mrcutfish.tumblr.com/post/159212103466/mb-sd-connect-4-local-and-administration-parameter

XTOOL X100 PAD2 Oil Reset Functions Introduction

X-100 PAD2 is the first tablet key programmer in the world! It not only provides customers with professional key programming, but also the most needed special functions for workshop.

XTOOL X-100 PAD2 Oil Reset Functions Features:

Innovative one-click oil reset for VW, Audi, BMW, Mercedes Seat, Skoda, Volvo, etc.
Support engine oil, spark plugs, front brake pads, back brake pads, air conditioner, brake liquid, coolant liquid, vehicle checking , etc. resetting for BMW. And the supported BMW models are F01/F02/F03/F04/F07/F10/F11/F12/F13/F18/F20/F30, etc.
Support Mercedes Benz new C Class, E Class models and Mercedes Benz VITO/VIANO/SPINTER.
Support the lifespan percentage resetting of engine oil for Buick, Cadillac etc.
Support Porsche Cayenne, Panamera till 2012
Support maintenance light reset for Volvo, Land Rover.

Xtool x100 pad2 detail info:http://www.uobdii.com/wholesale/xtool-x-100-pad-2.html

Launch X431 V 8″ Lenovo Tablet Vs Cracked Autocom/Delphi Ds150e

Launch X431 V professional universal diagnostic tool with newest database and many special functions are covered. Autocom/Delphi Ds150e Clone is PC-based with normal function and little special function. More detailed comparison as below.OBD2 tool

Comparison Content:
1) Launch X431 V 8″ is compatible with Android tablet and` phone, it is handheld and no bother installing driver and program.Xhorse VVDI
Cracked Autocom/Delphi Ds150e is windows-based and need to install driver.

2) About function (Special function):
Autocom/Delphi Ds150e Clone is with normal function, A LOT OF SPECIAL function DOES NOT EXIST OR DOES NOT WORK.
Launch X431 V 8″ covers full range car models and perform full car system diagnosis include: Read DTCs, Clear DTCs, Read data stream.
X431 V 8 inch includes more special functions incl. Oil Reset Service, Steering Angle Calibration, Electronic Parking Brake Reset, Battery Register / Battery Maintenance, ABS Bleeding, Electronic Throttle Position Reset / Learn, Diesel Particulate Filter (DPF) Regeneration, Tire Pressure Monitor System Reset, specifically, BMW idle study, BMW injection rate adjustment, BMW battery replacement, Nissan matching key, Renault - airbags coding ON/OFF, like on Clip tool.
Programming: some models support online programming.Lanuch X431

3) About database:

In short I suggest buy original launch X431 V 8 inch for 799$ and you will have best solution because of the price of what you pay.
The only way that you have that big database and functions is to buy original software from Delphi, autocom or wurth, because there is no new version than 2014.03V.
And Launch X431 V haves far more than Delphi and others because launch you can have with 2016 database and even 2017 database for Ford and Mazda incl. Escape, MKC, Fusion, MKZ, Expedition, Navigator, Transit Connect, Explorer, Transit Connect, Super Duty, F150 etc. and believe me it is big difference.
Autel Scanner
3) About vehicle coverage:
X431 V is much better in model coverage for old Asia (10+ years, basicly Autocom/Delphi will never support this models good+Asia adapters was never developed) and sometime better functions for new Asia (younger than 10 years, this models are included in AC/D). About European brands are both tools perfect.
http://blog.uobdii.com/launch-x431-v-8inch-tablet-tested-vehicle-list-89-diagnostic-software-in-total/ this is X431 V vehicle coverage3) About after-sale service
Launch X431 V 8″: Tap the "Remote Diagnosis" option and through CC number no need TV, you could gain instant messaging and remote diagnosis.
Autocom/Delphi users usually use Team viewer (TV) to get remote assistance by supplier.XTOOL TOOL
4) About Update:
Launch X431 V 8″ update is free for the first two years and upgrade every one month.
Autocom/Delphi Ds150e Clone is no new version than 2014.03V for long time.5) About Legal:
If you want it legal, then you can buy Launch X431 V 8 inch, it has the same functions like X431 V 7", run faster than 7″ since it has better configuration.6) About language available
Launch X431 V 8″ language available: English, German, Japanese, Russian, French, Korea, Arabic, Spanish, Italy, Portuguese, Polish, Turkish, Dutch, Greek, Hungarian, Arabic, Danish, Persian, Romanian, Serbian, Finnish, Swedish and Czech.
Autocom/Delphi Ds150e Clone language available: English, Spanish, French, Italian, Portuguese, Czech, Dansk, German, Turkish, Greek, Dutch, Hungarian, Norwegian, Polish, Romanian, Russian, Serbian, Swedish.UOBDII All rights reserved Launch X431 V 8″ Lenovo Tablet Vs Cracked Autocom/Delphi Ds150e